Probabilistic characterization of wind turbine blades via aeroelasticity and spinning finite element formulation

2012 ◽  
Author(s):  
Antonio Velazquez ◽  
R. Andrew Swartz
Keyword(s):  
Finite Element ◽  
Wind Turbine ◽  
Turbine Blades ◽  
Finite Element Formulation ◽  
Element Formulation ◽  
Wind Turbine Blades ◽  
Probabilistic Characterization

Design and Optimization of Composite Offshore Wind Turbine Blades

2019 ◽  
Vol 141 (5) ◽  
Author(s):  
M. Tarfaoui ◽  
O. R. Shah ◽  
M. Nachtane
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Turbine Blades ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Skin Thickness ◽  
Wind Turbine Blades ◽  
Element Analysis

In order to obtain an optimal design of composite offshore wind turbine blade, take into account all the structural properties and the limiting conditions applied as close as possible to real cases. This work is divided into two stages: the aerodynamic design and the structural design. The optimal blade structural configuration was determined through a parametric study by using a finite element method. The skin thickness, thickness and width of the spar flange, and thickness, location, and length of the front and rear spar web were varied until design criteria were satisfied. The purpose of this article is to provide the designer with all the tools required to model and optimize the blades. The aerodynamic performance has been covered in this study using blade element momentum (BEM) method to calculate the loads applied to the turbine blade during service and extreme stormy conditions, and the finite element analysis was performed by using abaqus code to predict the most critical damage behavior and to apprehend and obtain knowledge of the complex structural behavior of wind turbine blades. The approach developed based on the nonlinear finite element analysis using mean values for the material properties and the failure criteria of Hashin to predict failure modes in large structures and to identify the sensitive zones.

scholarly journals Evaluation of Basalt Fibers on Wind Turbine Blades through Finite Element Analysis

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
V. García ◽  
L. Vargas ◽  
A. Acuña ◽  
J. B. Sosa ◽  
E. Durazo ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Wind Turbine ◽  
Material Properties ◽  
Turbine Blades ◽  
Operating Conditions ◽  
Basalt Fibers ◽  
Wind Turbine Blades ◽  
Element Analysis ◽  
Structural Requirements

Here we use finite element analysis to determine the suitability of basalt fiber as a substitute for E-glass in structural applications, which would improve the cost effectiveness of small wind turbine blades. Five NACA (National Advisory Committee for Aeronautics) profiles were evaluated to select the optimum shape for the wind operation conditions. To obtain the wind load pressure distribution over the blade, a computational aerodynamic analysis by CFD (computational fluid dynamics) was performed based on the blade’s design and operating conditions. Material properties and mechanical tests were carried out to obtain the fiber volume fraction, density, Young’s modulus, shear modulus, and Poisson relation of polymeric matrix composites made using basalt and fiberglass. The obtained wind loads and material properties were used on a FEM (finite element model) analysis to evaluate the structural behavior of the blade under normal and critical operating conditions. Both fibers meet the structural requirements under normal operating conditions. We detected a reduction of 4% in the blade stress when basalt fibers are used instead of glass fibers, and a reduction of 68% in the total deformation for a critical load case of 40 m/s was obtained when using basalt fibers, which met the structural requirements and maximum power generation required for this wind turbine design.

Sign in / Sign up

Export Citation Format

Share Document