PS InSAR processing methodologies in the detection of ground surface deformation: a case study of Nantong City

2011 ◽  
Author(s):  
Ruya Xiao ◽  
Xiufeng He ◽  
Min He
Keyword(s):  
Surface Deformation ◽  
Ground Surface

Survey and cause analyses of ground surface deformation near a foundation pit slope: a case study in the Three Gorges area, China

2014 ◽  
Vol 75 (1) ◽  
pp. 13-31 ◽  
Author(s):  
Guangcheng Zhang ◽  
Ni Xie ◽  
Huiming Tang ◽  
Lu Zhang ◽  
Jiangpeng Wu
Keyword(s):  
Surface Deformation ◽  
Ground Surface ◽  
Three Gorges ◽  
Foundation Pit ◽  
Three Gorges Area ◽  
The Three Gorges

scholarly journals Imaging ground surface deformations in post-disaster settings via small UAVs

2021 ◽  
Vol 8 (1) ◽  
Author(s):  
Richard L. Ybañez ◽  
Audrei Anne B. Ybañez ◽  
Alfredo Mahar Francisco A. Lagmay ◽  
Mario A. Aurelio
Keyword(s):  
Surface Deformation ◽  
Ground Surface ◽  
Point Clouds ◽  
Lateral Spreading ◽  
Fault Movement ◽  
Field Surveys ◽  
3D Point Clouds ◽  
Vertical Displacements ◽  
Resolution Imaging ◽  
Post Disaster

AbstractSmall unmanned aerial vehicles have been seeing increased deployment in field surveys in recent years. Their portability, maneuverability, and high-resolution imaging are useful in mapping surface features that satellite- and plane-mounted imaging systems could not access. In this study, we develop and apply a workplan for implementing UAV surveys in post-disaster settings to optimize the flights for the needs of the scientific team and first responders. Three disasters caused by geophysical hazards and their associated surface deformation impacts were studied implementing this workplan and was optimized based on the target features and environmental conditions. An earthquake that caused lateral spreading and damaged houses and roads near riverine areas were observed in drone images to have lengths of up to 40 m and vertical displacements of 60 cm. Drone surveys captured 2D aerial raster images and 3D point clouds leading to the preservation of these features in soft-sedimentary ground which were found to be tilled over after only 3 months. The point cloud provided a stored 3D environment where further analysis of the mechanisms leading to these fissures is possible. In another earthquake-devastated locale, areas hypothesized to contain the suspected source fault zone necessitated low-altitude UAV imaging below the treeline capturing Riedel shears with centimetric accuracy that supported the existence of extensional surface deformation due to fault movement. In the aftermath of a phreatomagmatic eruption and the formation of sub-metric fissures in nearby towns, high-altitude flights allowed for the identification of the location and dominant NE–SW trend of these fissures suggesting horst-and-graben structures. The workplan implemented and refined during these deployments will prove useful in surveying other post-disaster settings around the world, optimizing data collection while minimizing risk to the drone and the drone operators.

Seismic solutions utilizing existing in-mine infrastructure for mineral exploration: A case study from Maseve platinum mine, South Africa

2022 ◽  
Vol 41 (1) ◽  
pp. 54-61
Author(s):  
Moyagabo K. Rapetsoa ◽  
Musa S. D. Manzi ◽  
Mpofana Sihoyiya ◽  
Michael Westgate ◽  
Phumlani Kubeka ◽  
...  
Keyword(s):  
South Africa ◽  
Seismic Data ◽  
Mineral Exploration ◽  
Ground Surface ◽  
Seismic Survey ◽  
Noisy Environment ◽  
Borehole Data ◽  
Passive Seismic ◽  
Below Ground

We demonstrate the application of seismic methods using in-mine infrastructure such as exploration tunnels to image platinum deposits and geologic structures using different acquisition configurations. In 2020, seismic experiments were conducted underground at the Maseve platinum mine in the Bushveld Complex of South Africa. These seismic experiments were part of the Advanced Orebody Knowledge project titled “Developing technologies that will be used to obtain information ahead of the mine face.” In these experiments, we recorded active and passive seismic data using surface nodal arrays and an in-mine seismic land streamer. We focus on analyzing only the in-mine active seismic portion of the survey. The tunnel seismic survey consisted of seven 2D profiles in exploration tunnels, located approximately 550 m below ground surface and a few meters above known platinum deposits. A careful data-processing approach was adopted to enhance high-quality reflections and suppress infrastructure-generated noise. Despite challenges presented by the in-mine noisy environment, we successfully imaged the platinum deposits with the aid of borehole data and geologic models. The results open opportunities to adapt surface-based geophysical instruments to address challenging in-mine environments for mineral exploration.

3D Visual Technology of Geo-Deformation Disasters Induced by Mining Subsidence Based on ArcGIS Engine

2012 ◽  
Vol 500 ◽  
pp. 428-436 ◽  
Author(s):  
Ke Ming Yang ◽  
Jun Ting Ma ◽  
Bo Pang ◽  
Yi Bin Wang ◽  
Ran Wang ◽  
...  
Keyword(s):  
Coal Mining ◽  
Surface Deformation ◽  
Ground Deformation ◽  
Ground Surface ◽  
Horizontal Displacement ◽  
Mining Subsidence ◽  
Underground Coal Mining ◽  
Vertical Movements ◽  
Probability Integral Method ◽  
Arcgis Engine

Mining subsidence often produces significant horizontal and vertical movements at the ground surface, the surface deformation induced by underground coal mining can be predicted by probability integral method, and the surface geo-deformation disasters can be visualized based on GIS components. A three dimensional (3D) visualizing system of surface geo-deformation information is designed and developed with ArcGIS Engine and C# in the study. According to the surface deformation-predicted data induced by underground coal mining in Guobei Coalmine of Huaibei mine field, the extents and degrees of ground deformation disasters are visualized in 3D views for surface vertical subsidence, slope, curvature, horizontal displacement and horizontal strain based on the GIS-developed application platform.

scholarly journals Quantitative data analysis of ESAR data

2013 ◽  
Vol 11 ◽  
pp. 291-295
Author(s):  
N. Phruksahiran ◽  
M. Chandra
Keyword(s):  
Ground Surface ◽  
Quantitative Information ◽  
Polarization Property ◽  
Data Sets ◽  
Program Code ◽  
Quantitative Data Analysis ◽  
Linear Depolarization Ratio ◽  
German Aerospace ◽  
Differential Reflectivity

Abstract. A synthetic aperture radar (SAR) data processing uses the backscattered electromagnetic wave to map radar reflectivity of the ground surface. The polarization property in radar remote sensing was used successfully in many applications, especially in target decomposition. This paper presents a case study to the experiments which are performed on ESAR L-Band full polarized data sets from German Aerospace Center (DLR) to demonstrate the potential of coherent target decomposition and the possibility of using the weather radar measurement parameter, such as the differential reflectivity and the linear depolarization ratio to obtain the quantitative information of the ground surface. The raw data of ESAR has been processed by the SAR simulator developed using MATLAB program code with Range-Doppler algorithm.

Sign in / Sign up

Export Citation Format

Share Document