Sensor performance improvements for high-quality low-cost imaging systems in ophthalmic applications

2011 ◽  
Author(s):  
Andrei Plaian ◽  
Marco D'Aguanno ◽  
Paola Griggio
Keyword(s):  
Low Cost ◽  
Imaging Systems ◽  
High Quality ◽  
Performance Improvements ◽  
Sensor Performance

Evaluation of stereo imaging capabilities and parameters when using personal computers: Defining a low-cost high-quality system

1992 ◽  
Vol 50 (2) ◽  
pp. 1048-1049
Author(s):  
John M. Mackenzie
Keyword(s):  
Low Cost ◽  
Evaluation Criteria ◽  
Imaging Systems ◽  
Personal Computers ◽  
Stereo Imaging ◽  
High Quality ◽  
Display Devices ◽  
The One ◽  
The Cost

Over the past several years the capabilities of personal computers have advanced at a staggering rate. At the same time, the cost of the hardware has dropped to such a degree that one wonders whether such inexpensive hardware can perform adequately.The purpose of this discussion is to look at the minimum hardware necessary to do quality stereo imaging on CRT display devices and to discuss several important evaluation criteria in producing these stereo images.The most important criteria for producing high quality stereo pairs lies in the quality of the digitization of the image. Most TV rate imaging systems even after multiple frames are averaged are quite distorted and lack sufficient image detail. Slow scan imaging systems such as the one developed in this laboratory which use a gated integrator and can digitize at over one thousand pixels square with 256 gray levels produce images which are extremely close to photographic quality.

scholarly journals Urban Air Quality Modeling Using Low-Cost Sensor Network and Data Assimilation in the Aburrá Valley, Colombia

Atmosphere ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 91
Author(s):  
Santiago Lopez-Restrepo ◽  
Andres Yarce ◽  
Nicolás Pinel ◽  
O.L. Quintero ◽  
Arjo Segers ◽  
...  
Keyword(s):  
Air Quality ◽  
Data Assimilation ◽  
Transport Model ◽  
Cost Model ◽  
Low Cost ◽  
Model Performance ◽  
Monitoring Network ◽  
Correlation Factor ◽  
Chemical Transport Model ◽  
High Quality

The use of low air quality networks has been increasing in recent years to study urban pollution dynamics. Here we show the evaluation of the operational Aburrá Valley’s low-cost network against the official monitoring network. The results show that the PM2.5 low-cost measurements are very close to those observed by the official network. Additionally, the low-cost allows a higher spatial representation of the concentrations across the valley. We integrate low-cost observations with the chemical transport model Long Term Ozone Simulation-European Operational Smog (LOTOS-EUROS) using data assimilation. Two different configurations of the low-cost network were assimilated: using the whole low-cost network (255 sensors), and a high-quality selection using just the sensors with a correlation factor greater than 0.8 with respect to the official network (115 sensors). The official stations were also assimilated to compare the more dense low-cost network’s impact on the model performance. Both simulations assimilating the low-cost model outperform the model without assimilation and assimilating the official network. The capability to issue warnings for pollution events is also improved by assimilating the low-cost network with respect to the other simulations. Finally, the simulation using the high-quality configuration has lower error values than using the complete low-cost network, showing that it is essential to consider the quality and location and not just the total number of sensors. Our results suggest that with the current advance in low-cost sensors, it is possible to improve model performance with low-cost network data assimilation.

scholarly journals Linum usitatisimum L. is the most important crop in Russia for the production of high-quality oil with low cost (review)

2021 ◽  
Vol 640 (4) ◽  
pp. 042014
Author(s):  
E N Turin ◽  
A N Susskiy ◽  
R S Stukalov ◽  
M V Shestopalov ◽  
E L Turina ◽  
...  
Keyword(s):  
Low Cost ◽  
High Quality ◽  
Important Crop

Teledermatology Can Produce High-Quality Care at Low Cost

2003 ◽  
Vol 11 (4) ◽  
pp. 209-215 ◽  
Author(s):  
Keng Chen ◽  
Stephen Shumack ◽  
Richard Wootton
Keyword(s):  
Low Cost ◽  
Quality Care ◽  
High Quality ◽  
High Quality Care

The Preparation of High Quality CIS Films by Spraying Citrate-Capped Cu11In9 Alloy Nanoparticles Ink and RTP Process

2013 ◽  
Vol 787 ◽  
pp. 382-387
Author(s):  
Li Zhou ◽  
Yuan Kui Ding ◽  
Pai Feng Luo
Keyword(s):  
Raw Materials ◽  
Low Cost ◽  
Chalcopyrite Structure ◽  
Alloy Nanoparticles ◽  
System Research ◽  
Spherical Nanoparticles ◽  
Particle Agglomeration ◽  
Energy Band Gap ◽  
High Quality ◽  
Selenization Process

A facile low-cost non-vacuum process for fabrication of high quality CuInSe2(CIS) films is described, which indicates a promising way for the application in thin film solar cells. First, citrate-capped Cu11In9alloy nanoparticles are synthesized by hot-injection method after a system research on the different reaction time and Cu-In ratio of the raw materials. From the TEM and XRD results, we can see that uniform spherical nanoparticles with dominant Cu11In9phase and less particle-to-particle agglomeration are successfully achieved in this study. Then, employing spray and RTP selenization process, high quality CIS films with dense and big grains are obtained, which show the single chalcopyrite structure and the preferred (112) orientation. An energy band gap about 1.01 eV is measured through the absorption spectroscopy measurement in our work.

X-Ray Microanalysis of Art Glass Surfaces

2010 ◽  
Vol 18 (5) ◽  
pp. 28-31
Author(s):  
R.B. Simmons
Keyword(s):  
Heavy Metals ◽  
Low Cost ◽  
Metallic Surfaces ◽  
High Quality ◽  
X Ray ◽  
Skin Contact ◽  
Work Area ◽  
The World ◽  
Glass Surfaces ◽  
Glass Workers

In recent years there has been a virtual explosion in the world of art glass. New glass formulations have brought a host of new colors into the marketplace, and the availability of low-cost, high-quality torches and other tools has brought art glass to the hobbyist. In addition to burn risks and possible cutting injury, there are a number of less obvious hazards that should be known to novice glass workers. One of these is the presence of heavy metals in or on glass surfaces and possibly in the atmosphere immediately surrounding the work area, presenting both potential skin contact and inhalation hazards. This study examines the metallic surfaces generated on five glass colors commonly used in art glass jewelry.

Sign in / Sign up

Export Citation Format

Share Document