Experimental investigation of active rib stitch knitted architecture for flow control applications

2010 ◽  
Author(s):  
Julianna M. Abel ◽  
Poorna Mane ◽  
Benjamin Pascoe ◽  
Jonathan Luntz ◽  
Diann Brei
Keyword(s):  
Experimental Investigation ◽  
Flow Control ◽  
Control Applications

Comparative Evaluation of Dielectric Materials for Plasma Actuators Active Flow Control and Heat Transfer Applications

2021 ◽  
Author(s):  
F. F. Rodrigues ◽  
J. Nunes-Pereira ◽  
M. Abdollahzadeh ◽  
J. Pascoa ◽  
S. Lanceros-Mendez
Keyword(s):  
Heat Transfer ◽  
Flow Control ◽  
Dielectric Layer ◽  
Active Flow Control ◽  
Thermal Power ◽  
Dielectric Materials ◽  
Plasma Actuators ◽  
Dbd Plasma ◽  
Control Applications ◽  
Active Flow

Abstract Dielectric Barrier Discharge (DBD) plasma actuators are simple devices with great potential for active flow control applications. Further, it has been recently proven their ability for applications in the area of heat transfer, such as film cooling of turbine blades or ice removal. The dielectric material used in the fabrication of these devices is essential in determining the device performance. However, the variety of dielectric materials studied in the literature is very limited and the majority of the authors only use Kapton, Teflon, Macor ceramic or poly(methyl methacrylate) (PMMA). Furthermore, several authors reported difficulties in the durability of the dielectric layer when the actuators operate at high voltage and frequency. Also, it has been reported that, after long operation time, the dielectric layer suffers degradation due to its exposure to plasma discharge, degradation that may lead to the failure of the device. Considering the need of durable and robust actuators, as well as the need of higher flow control efficiencies, it is highly important to develop new dielectric materials which may be used for plasma actuator fabrication. In this context, the present study reports on the experimental testing of dielectric materials which can be used for DBD plasma actuators fabrication. Plasma actuators fabricated of poly(vinylidene fluoride) (PVDF) and polystyrene (PS) have been fabricated and evaluated. Although these dielectric materials are not commonly used as dielectric layer of plasma actuators, their interesting electrical and dielectric properties and the possibility of being used as sensors, indicate their suitability as potential alternatives to the standard used materials. The plasma actuators produced with these nonstandard dielectric materials were analyzed in terms of electrical characteristics, generated flow velocity and mechanical efficiency, and the obtained results were compared with a standard actuator made of Kapton. An innovative calorimetric method was implemented in order to estimate the thermal power transferred by these devices to an adjacent flow. These results allowed to discuss the ability of these new dielectric materials not only for flow control applications but also for heat transfer applications.

Novel Hierarchical Modular Control Methodology for Closed-Loop-Flow Control Applications

2005 ◽  
Vol 42 (5) ◽  
pp. 1099-1108 ◽  
Author(s):  
Mehul P. Patel ◽  
Richard M. Kolacinski ◽  
Troy S. Prince ◽  
T. Terry Ng ◽  
James H. Myatt
Keyword(s):  
Flow Control ◽  
Closed Loop ◽  
Control Applications ◽  
Modular Control ◽  
Control Methodology

Experimental investigation of dynamic stall flow control for wind turbine airfoils using a plasma actuator

Energy ◽  
2019 ◽  
Vol 185 ◽  
pp. 90-101 ◽  
Author(s):  
Li Guoqiang ◽  
Zhang Weiguo ◽  
Jiang Yubiao ◽  
Yang Pengyu
Keyword(s):  
Experimental Investigation ◽  
Flow Control ◽  
Wind Turbine ◽  
Plasma Actuator ◽  
Dynamic Stall ◽  
Turbine Airfoils

Two-Step Electroplating Process in Fabrication of Thermal Bimorph Cantilever Actuator for Flow Control Application

2012 ◽  
Vol 225 ◽  
pp. 367-371 ◽  
Author(s):  
Alongkorn Pimpin ◽  
Eakayoot Wongweerayoot ◽  
Werayut Srituravanich
Keyword(s):  
Flow Control ◽  
Large Deflection ◽  
Fast Response ◽  
Fabrication Process ◽  
Total Thickness ◽  
Control Applications ◽  
Nickel Copper ◽  
Electroplating Process ◽  
Control Application

This work proposes a novel and simple fabrication process of a nickel-copper thermal bimorph actuator. This new fabrication process employs only two-step electroplating technique that is easy, cheap and compatible for various materials. In this study, the total thickness of fabricated cantilever actuator is around 80 μm, i.e. 30±10 and 50±10 μm for nickel and copper, respectively, and its length is equal to 22.5 mm. For actuator’s width, it is varied as 258±7, 351±7 and 447±7 μm. After heating by applying current through the actuator’s structure, the actuator bends up due to the elongation mismatch between copper and nickel elements. It is found that the deflection becomes larger for a narrower actuator. From the experiments, the deflection at current of 2.5A for 258±7 μm wide actuator is approximately equal to 4 mm. In addition, the response of all actuators is faster than 1 Hz. With obtained large deflection and fast response, the fabricated actuators are viable to employ for flow control applications.

Sign in / Sign up

Export Citation Format

Share Document