Identification of two-phase flow regime based on electrical capacitance tomography and soft-sensing technique

2008 ◽  
Author(s):  
Lifeng Zhang ◽  
Huaxiang Wang
Keyword(s):  
Flow Regime ◽  
Two Phase Flow ◽  
Electrical Capacitance Tomography ◽  
Phase Flow ◽  
Electrical Capacitance ◽  
Two Phase ◽  
Soft Sensing ◽  
Capacitance Tomography

Horizontal Two Phase Flow Regime Identification: Comparison of Pressure Signature, Electrical Capacitance Tomography (ECT) and High Speed Visualization

2012 ◽  
Author(s):  
Paul J. Kreitzer ◽  
Michael Hanchak ◽  
Larry Byrd
Keyword(s):  
Flow Regime ◽  
High Speed ◽  
Two Phase Flow ◽  
Flow Regimes ◽  
Electrical Capacitance Tomography ◽  
Phase Flow ◽  
Electrical Capacitance ◽  
Flow Conditions ◽  
Two Phase ◽  
Capacitance Tomography

Understanding the behavior of transient two phase refrigerant flow is an important aspect of implementing vapor compression systems in future aerospace applications. Pressure drop and heat transfer coefficient are important parameters that guide the design process, and are influenced by flow regime. Published two phase flow models rely heavily on a priori knowledge of the current two phase flow conditions including flow regime. Additional complications arise when applying published correlations to a range of systems because each correlation is based on a specific set of experimental conditions, including working fluid, flow orientation, channel size, and channel shape. Non-intrusive measurement techniques provide important advantages while measuring the behavior of two phase flow systems. A two phase flow experimental test rig has been developed at the Air Force Research Laboratory, providing a closed loop refrigeration system capable of producing flow regimes from bubbly through annular flow. Two phase flow is produced by pumping subcooled R134a through a heat exchanger with 40 minichannels into an adiabatic transparent fused quartz observation channel with a hydraulic diameter of 7 mm. Refrigerant mass flux is varied from 100–400 kg/m2s with a heat flux from 0–15.5 W/cm2. Temperatures ranged from 18–25 °C and pressures between 550–750 kPa. The data from high speed pressure transducers were analyzed using standard signal processing techniques to identify the different flow regimes. Initial results indicate that different flow regimes can be identified from their pressure signature. In addition, real-time void fraction measurements were taken using Electrical Capacitance Tomography (ECT). This paper describes the process behind ECT systems used to measure two phase flow conditions. Comparisons with high speed video assess the accuracy of ECT measurements in identifying various two phase flow conditions. Results indicate variations between ECT and high speed images, however, enough information is provided to create flow pattern maps and regime identification for different superficial vapor and liquid velocities.

scholarly journals Investigating the Characteristics of Two-Phase Flow Using Electrical Capacitance Tomography (ECT) for Three Pipe Orientations

Processes ◽  
2020 ◽  
Vol 8 (1) ◽  
pp. 51 ◽  
Author(s):  
Zeyad Almutairi ◽  
Fayez M. Al-Alweet ◽  
Yusif A. Alghamdi ◽  
Omar A. Almisned ◽  
Othman Y. Alothman
Keyword(s):  
High Speed ◽  
Two Phase Flow ◽  
Flow Patterns ◽  
Electrical Capacitance Tomography ◽  
Experimental Measurements ◽  
Phase Flow ◽  
Electrical Capacitance ◽  
Liquid Holdup ◽  
Two Phase ◽  
Capacitance Tomography

Experiments of gas–liquid flow in a circular pipe for horizontal and inclined positions (upward/downward) are reported. The characteristics of two-phase flow in terms of liquid holdup (ε(L)) and induced flow patterns are studied using three experimental techniques; time-averaged ε(L) from permittivity profiles using electrical capacitance tomography (ECT), instantaneous ε(L) using two fast-closing valves (TFCV), and high-speed camera images (HSCI) to capture/identify the formed flow patterns. Thus, this experimental setup enables the development of more well-defined flow patterns in gas–liquid two-phase flow and allows for multi-technique verification of the results. Taken from experimental measurements, a model is proposed to predict ε(L) for high and low situations. The correlations are a function of the hydrodynamic dimensionless quantities which provide hydrodynamic similarity. Regarding different pipe orientations, ε(L) predictions are comparable to ε(L) from experimental measurements with accepted accuracy: 88% of the predictions are within ±5–15% and 98% are below ±20%. The correlations also were validated by reported results and against correlations available in the literature and show higher prediction accuracy. It is confirmed that the kinematic similarity which is achieved by the gas–liquid velocity ratios and the inertial forces influence the flow pattern and the liquid holdup.

scholarly journals Experimental Comparison Between Wire Mesh and Electrical Capacitance Tomography Sensors to Predict a Two-Phase Flow Behaviour and Patterns in Inclined Pipe

2021 ◽  
Vol 3 (5) ◽  
pp. 49-63
Author(s):  
Ali I. Hameed ◽  
Lokman A. Abdulkareem ◽  
Raid A. Mahmood
Keyword(s):  
Two Phase Flow ◽  
Flow Behaviour ◽  
Wire Mesh ◽  
Electrical Capacitance Tomography ◽  
Phase Flow ◽  
Electrical Capacitance ◽  
Two Phase ◽  
Inclined Pipe ◽  
Capacitance Tomography ◽  
Oil Gas

Two-phase flow behaviour and its flow patterns have a significant effect in many applications in industry. Oil-gas is one of the two-phase flow types that have many applications in petroleum and power stations. An oil-gas two-phase flow behaviour and flow patterns have been investigated in an inclined pipe using two different tomography sensors: Wire Mesh sensor (WMS) and Electrical Capacitance Tomography (ECT). A special experimental facility was designed and built to operate the tow-phase flow application in the inclined pipe with the various angle of inclination. A set of experimental data were collected using operating conditions which covered a two-phase flow range of superficial velocity of gas (Usl) from 0.05 to 0.52 m/s and superficial velocity of liquid (Usg) from 0.05 to 4.7 m/s at atmospheric pressure and room temperature. Three inclined angles to change the pipe’s inclination 45, 60, and 80-degree were applied in the experiments. The Comparison between the Wire Mesh Sensor (WMS) and Electrical Capacitance Tomography (ECT) was completed experimentally. The results revealed that there is a good agreement between the two sensors, however; the WMS had a higher frequency which was calculated 1000 frames per second compared with the ECT which worked at 200 frames per second.

Sign in / Sign up

Export Citation Format

Share Document