Dynamic strain-field hysteresis model for ferromagnetic shape memory Ni-Mn-Ga

2008 ◽  
Author(s):  
Neelesh N. Sarawate ◽  
Marcelo J. Dapino
Keyword(s):  
Shape Memory ◽  
Strain Field ◽  
Dynamic Strain ◽  
Hysteresis Model ◽  
Ferromagnetic Shape Memory

Magnetic properties of ferromagnetic shape memory alloys Ni _{2-x} Cu _{x} MnGa

2005 ◽  
Vol 21 (3-4) ◽  
pp. 151-157 ◽  
Author(s):  
Takeshi Kanomata ◽  
Takuji Nozawa ◽  
Daisuke Kikuchi ◽  
Hironori Nishihara ◽  
Keiichi Koyama ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Shape Memory Alloys ◽  
Shape Memory ◽  
Ferromagnetic Shape Memory Alloys ◽  
Ferromagnetic Shape Memory

Magnetic, magneto-optical, and transport properties of ferromagnetic shape-memory Ni2MnGa alloy

2003 ◽  
Vol 93 (10) ◽  
pp. 6975-6977 ◽  
Author(s):  
S. J. Lee ◽  
Y. P. Lee ◽  
Y. H. Hyun ◽  
Y. V. Kudryavtsev
Keyword(s):  
Shape Memory ◽  
Transport Properties ◽  
Ferromagnetic Shape Memory

Effects of Annealing on Microstructure and Martensitic Transition of Ni-Mn-Co-In Ferromagnetic Shape Memory Alloys

2011 ◽  
Vol 674 ◽  
pp. 171-175
Author(s):  
Katarzyna Bałdys ◽  
Grzegorz Dercz ◽  
Łukasz Madej
Keyword(s):  
Electron Microscopy ◽  
Shape Memory Alloys ◽  
Shape Memory ◽  
Smart Materials ◽  
Martensitic Transition ◽  
Magnetic Shape Memory ◽  
Ferromagnetic Shape Memory Alloys ◽  
Initial State ◽  
X Ray ◽  
Ferromagnetic Shape Memory

The ferromagnetic shape memory alloys (FSMA) are relatively the brand new smart materials group. The most interesting issue connected with FSMA is magnetic shape memory, which gives a possibility to achieve relatively high strain (over 8%) caused by magnetic field. In this paper the effect of annealing on the microstructure and martensitic transition on Ni-Mn-Co-In ferromagnetic shape memory alloy has been studied. The alloy was prepared by melting of 99,98% pure Ni, 99,98% pure Mn, 99,98% pure Co, 99,99% pure In. The chemical composition, its homogeneity and the alloy microstructure were characterized using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The phase composition was also studied by X-ray analysis. The transformation course and characteristic temperatures were determined by the use of differential scanning calorimetry (DSC) and magnetic balance techniques. The results show that Tc of the annealed sample was found to decrease with increasing the annealing temperature. The Ms and Af increases with increasing annealing temperatures and showed best results in 1173K. The studied alloy exhibits a martensitic transformation from a L21 austenite to a martensite phase with a 7-layer (14M) and 5-layer (10M) modulated structure. The lattice constants of the L21 (a0) structure determined by TEM and X-ray analysis in this alloy were a0=0,4866. The TEM observation exhibit that the studied alloy in initial state has bigger accumulations of 10M and 14M structures as opposed from the annealed state.

Microscopic considerations for models of ferromagnetic shape memory actuation

2002 ◽  
Author(s):  
Robert C. O'Handley ◽  
David I. Paul ◽  
Miguel A. Marioni ◽  
Christopher P. Henry ◽  
Marc Richard ◽  
...  
Keyword(s):  
Shape Memory ◽  
Ferromagnetic Shape Memory

Rapid-Solidified Metallic Actuator Materials Developed by Electromagnetic Nozzleless Melt Spinning Method

1999 ◽  
Vol 604 ◽  
Author(s):  
Y. Furuya
Keyword(s):  
Shape Memory ◽  
Rapid Solidification ◽  
Melt Spinning ◽  
Material Design ◽  
Thin Plates ◽  
Molten Metals ◽  
Short Fibers ◽  
Crystal Anisotropy ◽  
Electro Magnetic ◽  
Ferromagnetic Shape Memory

AbstractElectro-magnetic nozzleless melt-spinning method was developed by combining the control of the flow down of the molten metals after electromagnetic float-melting(i.e. levitation) with rapid solidification by rotating roll. The metallurgical grain microstructures can be changed by rotating roll speed. It was confinned that the produced, intermetallic TiNi and NiAl system alloy thin plates showed the strong crystal anisotropy, higher shape memory functional properties than those of the conventionally processed melt-worked samples having its same origin. As new SMAs by using this method, ferromagnetic shape memory, FePd alloy having very large magnetostriction and super high temperature shape memory, RuTa alloy having the transformation over 1000°C were developed. Moreover, our recent study on the advanced rapid-solidification machine to produce many kinds of short fibers as well as ribbons is introduced. Finally, harmonic material design for sensor/actuator stacking composite system, namely “Smart Board” for aircraft structures will be introduced.

Sign in / Sign up

Export Citation Format

Share Document