Thermomechanical characterization of a TiPdNi high temperature SMA under tension

2007 ◽  
Author(s):  
Parikshith K. Kumar ◽  
Dimitris C. Lagoudas
Keyword(s):  
High Temperature ◽  
Thermomechanical Characterization

Thermomechanical characterization of high temperature SMA actuators

2006 ◽  
Author(s):  
Parikshith K. Kumar ◽  
Dimitris C. Lagoudas ◽  
Kevin J. Zanca ◽  
Magdalini Z. Lagoudas
Keyword(s):  
High Temperature ◽  
Sma Actuators ◽  
Thermomechanical Characterization

Thermomechanical characterization of a fire clay refractory made of algerian kaolin

2012 ◽  
Vol 37 (2-4) ◽  
pp. 71-84 ◽  
Author(s):  
Mostafa Kolli ◽  
Mohamed Hamidouche ◽  
Noureddine Bouaouadja ◽  
Gilbert Fantozzi
Keyword(s):  
Fire Clay ◽  
Thermomechanical Characterization

scholarly journals Fabrication and Characterization of Quinary High Entropy-Ultra-High Temperature Diborides

Ceramics ◽  
2021 ◽  
Vol 4 (2) ◽  
pp. 108-120
Author(s):  
Simone Barbarossa ◽  
Roberto Orrù ◽  
Valeria Cannillo ◽  
Antonio Iacomini ◽  
Sebastiano Garroni ◽  
...  
Keyword(s):  
High Temperature ◽  
Single Phase ◽  
Nominal Composition ◽  
High Entropy ◽  
Chemical Complexity ◽  
Alternative Processing ◽  
Plasma Sintering ◽  
High Temperature Synthesis ◽  
Spark Plasma

Due to their inherent chemical complexity and their refractory nature, the obtainment of highly dense and single-phase high entropy (HE) diborides represents a very hard target to achieve. In this framework, homogeneous (Hf0.2Nb0.2Ta0.2Mo0.2Ti0.2)B2, (Hf0.2Zr0.2Ta0.2Mo0.2Ti0.2)B2, and (Hf0.2Zr0.2Nb0.2Mo0.2Ti0.2)B2 ceramics with high relative densities (97.4, 96.5, and 98.2%, respectively) were successfully produced by spark plasma sintering (SPS) using powders prepared by self-propagating high-temperature synthesis (SHS). Although the latter technique did not lead to the complete conversion of initial precursors into the prescribed HE phases, such a goal was fully reached after SPS (1950 °C/20 min/20 MPa). The three HE products showed similar and, in some cases, even better mechanical properties compared to ceramics with the same nominal composition attained using alternative processing methods. Superior Vickers hardness and elastic modulus values were found for the (Hf0.2Nb0.2Ta0.2Mo0.2Ti0.2)B2 and the (Hf0.2Zr0.2Ta0.2Mo0.2Ti0.2)B2 systems, i.e., 28.1 GPa/538.5 GPa and 28.08 GPa/498.1 GPa, respectively, in spite of the correspondingly higher residual porosities (1.2 and 2.2 vol.%, respectively). In contrast, the third ceramic, not containing tantalum, displayed lower values of these two properties (25.1 GPa/404.5 GPa). However, the corresponding fracture toughness (8.84 MPa m1/2) was relatively higher. This fact can be likely ascribed to the smaller residual porosity (0.3 vol.%) of the sintered material.

scholarly journals Multianvil High-Pressure/High-Temperature Synthesis and Characterization of multiferroic HP-Co3TeO6

2021 ◽  
Author(s):  
Gunter Heymann ◽  
Elisabeth Selb ◽  
Toni Buttlar ◽  
Oliver Janka ◽  
Martina Tribus ◽  
...  
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Type Structure ◽  
Synthesis And Characterization ◽  
Temperature Synthesis ◽  
Space Group ◽  
Crystal System ◽  
High Temperature Synthesis ◽  
High Pressure High Temperature

By high-pressure/high-temperature multianvil synthesis a new high-pressure (HP) phase of Co3TeO6 was obtained. The compound crystallizes in the acentric trigonal crystal system of the Ni3TeO6-type structure with space group R3...

Sign in / Sign up

Export Citation Format

Share Document