Research on sampling method for three-dimensional flow field reconstruction of incomplete data

2006 ◽  
Author(s):  
Hongbing Yao ◽  
Xia Ye ◽  
Jun Zhou ◽  
Guilin Ding ◽  
Anzhi He
Keyword(s):  
Flow Field ◽  
Incomplete Data ◽  
Sampling Method ◽  
Three Dimensional ◽  
Three Dimensional Flow ◽  
Field Reconstruction ◽  
Dimensional Flow ◽  
Flow Field Reconstruction

Simulation of Three-Dimensional Flow Field Around Unconventional Bridge Piers

2017 ◽  
Author(s):  
Adnan Ismael ◽  
Hamid Hussein ◽  
Mohammed Tareq ◽  
Mustafa Gunal
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Bridge Piers ◽  
Three Dimensional Flow ◽  
Dimensional Flow

Experimental investigation on the three-dimensional flow field from a meltblowing slot die

e-Polymers ◽  
2020 ◽  
Vol 20 (1) ◽  
pp. 724-732
Author(s):  
Changchun Ji ◽  
Yudong Wang
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Great Influence ◽  
Distribution Characteristics ◽  
Air Velocity ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Airflow Distribution ◽  
Slot Die ◽  
Center Area

AbstractTo investigate the distribution characteristics of the three-dimensional flow field under the slot die, an online measurement of the airflow velocity was performed using a hot wire anemometer. The experimental results show that the air-slot end faces have a great influence on the airflow distribution in its vicinity. Compared with the air velocity in the center area, the velocity below the slot end face is much lower. The distribution characteristics of the three-dimensional flow field under the slot die would cause the fibers at different positions to bear inconsistent air force. The air velocity of the spinning centerline is higher than that around it, which is more conducive to fiber diameter attenuation. The violent fluctuation of the instantaneous velocity of the airflow could easily cause the meltblowing fiber to whip in the area close to the die.

scholarly journals Transient Three-Dimensional Flow Field Measurements by Means of 3D µPTV in Drying Poly(Vinyl Acetate)-Methanol Thin Films Subject to Short-Scale Marangoni Instabilities

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1223
Author(s):  
Max Tönsmann ◽  
Philip Scharfer ◽  
Wilhelm Schabel
Keyword(s):  
Flow Field ◽  
Vinyl Acetate ◽  
Three Dimensional ◽  
Field Measurements ◽  
Initial Assessment ◽  
Ambient Conditions ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Short Scale ◽  
Dry Film

Convective Marangoni instabilities in drying polymer films may induce surface deformations, which persist in the dry film, deteriorating product performance. While theoretic stability analyses are abundantly available, experimental data are scarce. We report transient three-dimensional flow field measurements in thin poly(vinyl acetate)-methanol films, drying under ambient conditions with several films exhibiting short-scale Marangoni convection cells. An initial assessment of the upper limit of thermal and solutal Marangoni numbers reveals that the solutal effect is likely to be the dominant cause for the observed instabilities.

Study of Flow Field in Compact Spinning with Pneumatic Groove

2011 ◽  
Vol 332-334 ◽  
pp. 260-263
Author(s):  
Shi Rui Liu
Keyword(s):  
Flow Field ◽  
Negative Pressure ◽  
Static Pressure ◽  
Three Dimensional ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Compact Zone ◽  
Air Flows ◽  
Compact Spinning

In the paper the structure of the compact spinning with pneumatic groove is introduced and the characteristics of three-dimensional flow field of the compact spinning with pneumatic groove are also investigated. Results from this research confirmed that In the compact zone, the air flows to the groove and enters the inner hollow of the slot-roller through the round holes, and the air on both sides of the groove condenses to the center of it and flows to the round holes; It is beneficial to compact the fiber and make the fiber slip to the bottom of the groove with shrink shape; the velocity and negative pressure are both not homogeneous, as the round holes are not continual, and the gradient of static pressure and velocity in compact zones are also perceptible.

The Influence of Endwall Contouring on the Performance of a Turbine Nozzle Guide Vane

1998 ◽  
Author(s):  
Vincenzo Dossena ◽  
Antonio Perdichizzi ◽  
Marco Savini
Keyword(s):  
Flow Field ◽  
Gas Turbine ◽  
Guide Vane ◽  
Three Dimensional ◽  
Angle Distribution ◽  
Secondary Effects ◽  
Three Dimensional Flow ◽  
Nozzle Height ◽  
Dimensional Flow ◽  
Endwall Contouring

The paper presents the results of a detailed investigation of the flow field in a gas turbine linear cascade. A comparison between a contoured and a planar configuration of the same cascade has been performed, and differences in the three-dimensional flow field are here analyzed and discussed. The flow evolution downstream of the trailing edge was surveyed by means of probe traversing while a 3-D Navier-Stokes solver was employed to obtain information on flow structures inside the vaned passages. The experimental measurements and the numerical simulation of the three-dimensional flow field has been performed for two cascades; one with planar endwalls, and the other with one planar and one profiled endwall, so as to present a reduction of the nozzle height. The investigation was carried out at an isentropic downstream Mach number of 0.6. Airfoils of both cascades were scaled from the same high pressure gas turbine inlet guide vane. Measurements of the three-dimensional flow field have been performed on five planes downstream of the cascades by means of a miniaturized five-hole pressure probe. The presence of endwall contouring strongly influences the secondary effects; the vortex generation and their development is inhibited by the stronger acceleration taking place throughout the cascade. The results show that the secondary effects on the contoured side of the passage are confined in the endwall region, while on the flat side the secondary vortices display characteristics similar to the ones occurring downstream of the planar cascade. The spanwise outlet angle distribution presents a linear variation for most of the nozzle height, with quite low values approaching the contoured endwall. The analysis of mass averaged losses shows a significant performance improvement in the contoured cascade. This has to be ascribed not only to lower secondary losses but also to a reduction of the profile losses.

scholarly journals The Three-dimensional Flow Field around Planets on Eccentric Orbits

2021 ◽  
Vol 915 (2) ◽  
pp. 113
Author(s):  
Avery Bailey ◽  
James M. Stone ◽  
Jeffrey Fung
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Eccentric Orbits
Sign in / Sign up

Export Citation Format

Share Document