Optimal design parameters research for novel monolithically integrated non-linear all-optical loop mirror for signal regeneration

2006 ◽  
Author(s):  
E. Moll ◽  
K. A. Williams ◽  
R. V. Penty ◽  
I. H. White
Keyword(s):  
Optimal Design ◽  
Design Parameters ◽  
Monolithically Integrated ◽  
Signal Regeneration ◽  
All Optical ◽  
Non Linear ◽  
Loop Mirror

scholarly journals Optimal Design of Earthquake-Resistant Buildings Based on Neural Network Inversion

2021 ◽  
Vol 11 (10) ◽  
pp. 4654
Author(s):  
Carlo Calledda ◽  
Augusto Montisci ◽  
Maria Cristina Porcu
Keyword(s):  
Neural Network ◽  
Optimal Design ◽  
Seismic Analysis ◽  
Three Dimensional ◽  
Structural Response ◽  
Time History ◽  
Optimal Choice ◽  
Design Parameters ◽  
Earthquake Resistant ◽  
Non Linear

An effective seismic design entails many issues related to the capacity-based assessment of the non-linear structural response under strong earthquakes. While very powerful structural calculation programs are available to assist the designer in the code-based seismic analysis, an optimal choice of the design parameters leading to the best performance at the lowest cost is not always assured. The present paper proposes a procedure to cost-effectively design earthquake-resistant buildings, which is based on the inversion of an artificial neural network and on an optimization algorithm for the minimum total cost under building code constraints. An exemplificative application of the method to a reinforced-concrete multi-story building, with seismic demands corresponding to a medium-seismicity Italian zone, is shown. Three design-governing parameters are assumed to build the input matrix, while eight capacity-design target requirements are assigned for the output dataset. A non-linear three-dimensional concentrated plasticity model of the structure is implemented, and time-history dynamic analyses are carried out with spectrum-consistent ground motions. The results show the promising ability of the proposed approach for the optimal design of earthquake-resistant structures.

G Optimal Design in Non linear Models to Increase Silicon Oxide Purity Levels and Electrical Conductivity

2018 ◽  
pp. 150-155
Author(s):  
Muklas Rivai
Keyword(s):  
Electrical Conductivity ◽  
Optimal Design ◽  
Linear Models ◽  
Silicon Oxide ◽  
Information Matrix ◽  
Relevant Information ◽  
Non Linear

Optimal design is a design which required in determining the points of variable factors that would be attempted to optimize the relevant information so that fulfilled the desired criteria. The optimal fulfillment criteria based on the information matrix of the selected model.

Justification of design parameters of the fractional reaping conveyor and its devices for removal of beveled stems from under the wheels of the vehicle

2019 ◽  
Vol 1 (3) ◽  
pp. 1-10
Author(s):  
Mikhail M. Konstantinov ◽  
Ivan N. Glushkov ◽  
Sergey S. Pashinin ◽  
Igor I. Ognev ◽  
Tatyana V. Bedych
Keyword(s):  
Optimal Design ◽  
Technological Process ◽  
Design Parameters ◽  
Theoretical Studies ◽  
Optimal Parameters ◽  
Belt Conveyor ◽  
Grain Crops ◽  
Mode Of Operation ◽  
Optimal Values ◽  
Main Component

In this paper we consider the structural and technological process of the combine used in the process of separate harvesting of grain crops, as well as a number of its parameters. Among the main units of the combine, we allocate a conveyor and devices for removing beveled stems from under the wheels of the vehicle. The principle of operation of the conveyor at different phases of the Reaper and especially the removal of cut stems from under the wheels of the vehicle during operation of the Reaper. The results of theoretical studies on the establishment of the optimal design of the parameters of the belt conveyor are presented, the ranges of their optimal values are considered and determined. Studies on the establishment of optimal parameters of the screw divider in the Reaper, which is the main component of the device for removal of beveled stems, are presented. Taking into account the optimal design and mode of operation of the screw divider, the correct work is provided to remove the cut stems from under the wheels of the harvester.

All-Optical 20-μHz-Level Repetition Rate Stabilization of Mode Locking With a Nonlinear Amplifying Loop Mirror

2016 ◽  
Vol 34 (11) ◽  
pp. 2833-2837 ◽  
Author(s):  
Qiang Hao ◽  
Qingshan Zhang ◽  
Feihong Chen ◽  
Kangwen Yang ◽  
Heping Zeng
Keyword(s):  
Repetition Rate ◽  
Mode Locking ◽  
All Optical ◽  
Loop Mirror ◽  
Nonlinear Amplifying Loop Mirror

Modeling and Design of Enhanced All Optical Signal Regeneration Technique

Optik ◽  
2021 ◽  
pp. 166696
Author(s):  
Bhagwan Das ◽  
M.F.L Abdullah ◽  
Fayaz Ali Dharejo ◽  
Farah Deeba ◽  
Jawad Ali ◽  
...  
Keyword(s):  
Optical Signal ◽  
Signal Regeneration ◽  
All Optical

scholarly journals Optimal Design Parameters for a Phased Array Based Ultrasonic Polar Scan

2021 ◽  
pp. 1-1
Author(s):  
Jannes Daemen ◽  
Arvid Martens ◽  
Mathias Kersemans ◽  
Erik Verboven ◽  
Steven Delrue ◽  
...  
Keyword(s):  
Optimal Design ◽  
Phased Array ◽  
Design Parameters ◽  
Ultrasonic Polar Scan
Sign in / Sign up

Export Citation Format

Share Document