Two-dimensional thermal analysis for freezing of plant and animal cells by high-speed microscopic IR camera

2003 ◽  
Author(s):  
Junko Morikawa ◽  
Toshimasa Hashimoto ◽  
Eita Hayakawa ◽  
Hideyuki Uemura
Keyword(s):  
Thermal Analysis ◽  
High Speed ◽  
Two Dimensional ◽  
Animal Cells ◽  
Ir Camera

Evaluation of Package Defects by Thermal Imaging Techniques

2002 ◽  
Author(s):  
Yongmei Liu ◽  
Rajen Dias
Keyword(s):  
Infrared Thermography ◽  
Thermal Imaging ◽  
High Speed ◽  
Imaging Techniques ◽  
Thermal Response ◽  
Analysis Tool ◽  
Nondestructive Analysis ◽  
Ir Camera ◽  
External Heating

Abstract Study presented here has shown that Infrared thermography has the potential to be a nondestructive analysis tool for evaluating package sublayer defects. Thermal imaging is achieved by applying pulsed external heating to the package surface and monitoring the surface thermal response as a function of time with a high-speed IR camera. Since the thermal response of the surface is affected by the defects such as voids and delamination below the package surface, the technique can be used to assist package defects detection and analysis.

Load Spectrum Compiling and Fatigue Life Estimation of the Automobile Wheel Hub

2020 ◽  
Vol 13 ◽  
Author(s):  
Xintian Liu ◽  
Yang Qu ◽  
Xiaobing Yang ◽  
Yongfeng Shen
Keyword(s):  
Fatigue Life ◽  
High Speed ◽  
Two Dimensional ◽  
Load Spectrum ◽  
One Dimensional ◽  
Life Estimation ◽  
Load Spectra ◽  
Fatigue Life Estimation ◽  
Program Load Spectrum ◽  
Program Load

Background:: In the process of high-speed driving, the wheel hub is constantly subjected to the impact load from the ground. Therefore, it is important to estimate the fatigue life of the hub in the design and production process. Objective:: This paper introduces a method to study the fatigue life of car hub based on the road load collected from test site. Methods:: Based on interval analysis, the distribution characteristics of load spectrum are analyzed. The fatigue life estimation of one - dimensional and two - dimensional load spectra is compared by compiling load spectra. Results:: According to the S-N curve cluster and the one-dimensional program load spectrum, the estimated range fatigue life of the hub is 397,100 km to 529,700 km. For unsymmetrical cyclic loading, each level means and amplitude of load were obtained through the Goodman fatigue empirical formula, and then according to S-N curve clusters in the upper and lower curves and two-dimensional program load spectrum, estimates the fatigue life of wheel hub of the interval is 329900 km to 435200 km, than one-dimensional load spectrum fatigue life was reduced by 16.9% - 17.8%. Conclusion:: This paper lays a foundation for the prediction of fatigue life and the bench test of fatigue durability of auto parts subjected to complex and variable random loads. At the same time, the research method can also be used to estimate the fatigue life of other bearing parts or high-speed moving parts and assemblies.

Accelerating laser processes with a smart two-dimensional polygon mirror scanner for ultra-fast beam deflection

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Florian Roessler ◽  
André Streek
Keyword(s):  
Energy Distribution ◽  
Real Time ◽  
Laser Processing ◽  
High Speed ◽  
Beam Deflection ◽  
Two Dimensional ◽  
Heat Accumulation ◽  
Field Programmable ◽  
Drill Holes ◽  
Average Laser

Abstract In laser processing, the possible throughput is directly scaling with the available average laser power. To avoid unwanted thermal damage due to high pulse energy or heat accumulation during MHz-repetition rates, energy distribution over the workpiece is required. Polygon mirror scanners enable high deflection speeds and thus, a proper energy distribution within a short processing time. The requirements of laser micro processing with up to 10 kW average laser powers and high scan speeds up to 1000 m/s result in a 30 mm aperture two-dimensional polygon mirror scanner with a patented low-distortion mirror configuration. In combination with a field programmable gate array-based real-time logic, position-true high-accuracy laser switching is enabled for 2D, 2.5D, or 3D laser processing capable to drill holes in multi-pass ablation or engraving. A special developed real-time shifter module within the high-speed logic allows, in combination with external axis, the material processing on the fly and hence, processing of workpieces much larger than the scan field.

Sign in / Sign up

Export Citation Format

Share Document