Design of passive filter for magnet power supply based on chopper control

2021 ◽  
Author(s):  
Yonggao Zhang ◽  
Weiwei Yang ◽  
Peng Liu ◽  
Yinquan Yu ◽  
Weijun Shen
Keyword(s):  
Author(s):  
Agus Prasetyo ◽  
Fajar Bima D.R ◽  
Hendi Matalata

The adapter / power supply is a DC voltage source that is used to provide voltage or power to various electronic circuits that require DC voltage to operate. The main circuit of the power supply is  a rectifier, which is a circuit that converts an alternating signal (AC) into a direct signal (DC). The conversion process starts from rectification by the diode. In this paper, the Ripple Voltage Filter is carried out using a passive filter and the average voltage drop of the filter is 64%, the regulation (regulation) by the regulator circuit, the provision of this DC electrical energy source is to provide a unidirectional variable voltage ( DC) which aims to provide practical tools in Batanghari University electric laboratories while the benefits obtained from the research results are as a tool for practical activities in the electrical engineering laboratory of Batanghari University, Jambi.


Author(s):  
Denis Shandrigin ◽  
◽  
Denis Egorov ◽  
Viktor Novikov ◽  
Valery Dovgun ◽  
...  

Author(s):  
A. Tanaka ◽  
M. Yamaguchi ◽  
T. Hirano

The plasma polymerization replica method and its apparatus have been devised by Tanaka (1-3). We have published several reports on its application: surface replicas of biological and inorganic specimens, replicas of freeze-fractured tissues and metal-extraction replicas with immunocytochemical markers.The apparatus for plasma polymerization consists of a high voltage power supply, a vacuum chamber containing a hydrocarbon gas (naphthalene, methane, ethylene), and electrodes of an anode disk and a cathode of the specimen base. The surface replication by plasma polymerization in negative glow phase on the cathode was carried out by gassing at 0.05-0.1 Torr and glow discharging at 1.5-3 kV D.C. Ionized hydrocarbon molecules diffused into complex surface configurations and deposited as a three-dimensionally polymerized film of 1050 nm in thickness.The resulting film on the complex surface had uniform thickness and showed no granular texture. Since the film was chemically inert, resistant to heat and mecanically strong, it could be treated with almost any organic or inorganic solvents.


2019 ◽  
Vol 2 (1) ◽  
pp. 8-16 ◽  
Author(s):  
P. A. Khlyupin ◽  
G. N. Ispulaeva

Introduction: The co-authors provide an overview of the main types of wind turbines and power generators installed into wind energy devices, as well as advanced technological solutions. The co-authors have identified the principal strengths and weaknesses of existing wind power generators, if applied as alternative energy sources. The co-authors have proven the need to develop an algorithm for the selection of a wind generator-based autonomous power supply system in the course of designing windmill farms in Russia. Methods: The co-authors have analyzed several types of wind turbines and power generators. Results and discussions: The algorithm for the selection of a wind generator-based autonomous power supply system is presented as a first approximation. Conclusion: The emerging algorithm enables designers to develop an effective wind generator-based autonomous power supply system.


2019 ◽  
Vol 5 (1) ◽  
pp. 35-45
Author(s):  
Markus Dwiyanto Tobi ◽  
Alimuddin Mappa

The role of the power supply device is to produce, process and distribute energy sources. Telecommunication equipment can only operate if it has continuous supply. Therefore, to maintain the continuity of the supply, a UPS (Uninterruptable Power Supply) device system is needed so that the supply to the Essential Load device will remain available so that continuity will be maintained. This research designs and proposes how a series of automatic redundant switch systems on UPS to ensure the availability of power supply for the main equipment of telecommunications systems. The Auto switch circuit is designed to have 3 (three) working stages which will trigger the relay driver as control circuit, namely the normal working condition of the contactor input K1 is present, the input condition is zero (lost), and the input condition is present. This system can automatically supply power to telecommunications equipment.


2020 ◽  
Vol 20 (3) ◽  
pp. 209-215
Author(s):  
Hyun-Seok Song ◽  
Min-Ho Son ◽  
Sung-Ju Yoo ◽  
Do-Hyun Jung ◽  
Boo-Hee Park

Sign in / Sign up

Export Citation Format

Share Document