Maximizing the efficiency of laser-fabricated diffraction gratings on PET using direct laser interference patterning

2020 ◽  
Author(s):  
Marcos Soldera ◽  
Sabri Alamri ◽  
Sebastian Storm ◽  
Tim Kunze ◽  
Andrés Fabián Lasagni
Keyword(s):  
Diffraction Gratings ◽  
Laser Interference ◽  
Direct Laser ◽  
Direct Laser Interference Patterning

In-Depth Investigation of Copper Surface Chemistry Modification by Ultrashort Pulsed Direct Laser Interference Patterning

Langmuir ◽  
2020 ◽  
Vol 36 (45) ◽  
pp. 13415-13425 ◽  
Author(s):  
Daniel W. Müller ◽  
Anne Holtsch ◽  
Sarah Lößlein ◽  
Christoph Pauly ◽  
Christian Spengler ◽  
...  
Keyword(s):  
Surface Chemistry ◽  
Copper Surface ◽  
Laser Interference ◽  
Direct Laser ◽  
Surface Chemistry Modification ◽  
Direct Laser Interference Patterning

scholarly journals Direct Laser Interference Patterning of Diffraction Gratings in Safrofilcon-A Hydrogel: Fabrication and Hydration Assessment

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 679
Author(s):  
Daniel Sola ◽  
Stephan Milles ◽  
Andrés F. Lasagni
Keyword(s):  
Laser Fluence ◽  
Contact Lenses ◽  
Laser Source ◽  
Spatial Period ◽  
Laser Interference ◽  
Periodic Patterns ◽  
Hydration Properties ◽  
Water Contact ◽  
Direct Laser ◽  
Direct Laser Interference Patterning

Refractive index modification by laser micro-structuration of diffractive optical devices in ophthalmic polymers has recently been applied for refractive correction in the fields of optics and ophthalmology. In this work, Safrofilcon-A hydrogel, used as soft contact lenses, was processed by direct laser interference patterning (DLIP) to fabricate linear periodic patterns on the surface of the samples. Periodic modulation of the surface was attained under two-beam interference by using a Q-switched laser source with emission at 263 nm and 4 ns pulse duration. Features of processed areas were studied as a function of both the interference spatial period and the laser fluence. Optical confocal microscopy used to evaluate the topography of the processed samples showed that both structured height and surface roughness increased with laser fluence. Static water contact angle (WCA) measurements were carried out with deionized water droplets on the structured areas to evaluate the hydration properties of DLIP structures. It was observed that the laser structured areas induced a delay in the hydration process. Finally, microstructural changes induced in the structured areas were assessed by confocal micro-Raman spectroscopy showing that at low laser fluences the polymer structure remained almost unaltered. In addition, Raman spectra of hydrated samples recovered the original shape of areas structured at low laser fluence.

scholarly journals Improving Throughput and Microstructure Uniformity in Direct Laser Interference Patterning Utilizing Top-Hat Shaped Beams

2021 ◽  
Author(s):  
Mikhael El-Khoury ◽  
Bogdan Voisiat ◽  
Tim Kunze ◽  
Andrés Fabián Lasagni
Keyword(s):  
Intensity Distribution ◽  
Laser Interference ◽  
Gaussian Laser Beam ◽  
Laser Beam Intensity ◽  
Direct Laser ◽  
Standard Configuration ◽  
Laser Sources ◽  
Periodic Microstructures ◽  
Direct Laser Interference Patterning ◽  
The Impact

Abstract Uniform periodic microstructures formation over large areas is generally challenging in Direct Laser Interference Patterning (DLIP) due to the Gaussian laser beam intensity distribution inherent to most commercial laser sources. In this work, a diffractive fundamental beam-mode shaper (FBS) element is implemented in a four-beam DLIP optical setup to generate a square-shaped top-hat intensity distribution in the interference volume. The interference patterns produced by a standard configuration and the developed setup are measured and compared. In particular, the impact of both laser intensity distributions on process throughput as well as fill-factor is investigated by measuring the resulting microstructure height with height error over the structured surface. It is demonstrated that by utilizing top-hat-shaped interference patterns, it is possible to produce on average 44.8 % deeper structures with up to 60 % higher homogeneity at the same throughput. Moreover, the presented approach allows the production of microstructures with comparable height and homogeneity compared to the Gaussian intensity distribution with increased throughput of 53%.

Sign in / Sign up

Export Citation Format

Share Document