OPO residuals reduction with imaging metrology color per layer mode

Author(s):  
Shlomit Katz ◽  
Honggoo Lee ◽  
DongYoung Lee ◽  
Jinsoo Kim ◽  
Jaesun Woo ◽  
...  
Keyword(s):  
2008 ◽  
Vol 16 (02) ◽  
pp. 225-256 ◽  
Author(s):  
STEVEN A. STOTTS

A coupled-mode formalism based on complex Airy layer mode solutions is presented. It is an extension into the complex horizontal wavenumber plane of the companion article [Stotts, J. Acoust. Soc. Am.111 (2002) 1623–1643], referred to here as the real horizontal wavenumber version, which accounted for general ocean environments but was restricted to normal modes on the real horizontal wavenumber axis. A formulation of the expressions for both trapped and continuum complex coupling coefficients is developed to dramatically reduce computer storage requirements and to make the calculation more practical. The motivation of this work is to demonstrate the numerical implementation of the derivations and to apply the method to an example benchmark. Differences from the real horizontal wavenumber formalism are highlighted. The coupled equations are solved using the Lanczos method [Knobles, J. Acoust. Soc. Am.96 (1994) 1741–1747]. Comparisons of the coupled-mode solution to a parabolic equation solution for the ONR shelf break benchmark validate the results.


2021 ◽  
Vol 1016 ◽  
pp. 476-480
Author(s):  
Emanuele Ghio ◽  
Emanuela Cerri

Selective Laser Melting (SLM) builds a metallic part in a layer-by-layer mode with growth occurring along the vertical axis. Metallic powder layers are melted by a laser beam by programmed scan sequences inducing specific mechanical properties in the as-built samples according to process parameters. Post heat treatments are usually performed to optimise the mechanical behaviour. In this work, the effects induced by heat treatments at 175°, 200° and 225°C on SLMed bars of Al10SiMg were investigated as function of distance from the substrate plate. The bars were 300 mm height and in the as-built condition, Vickers microhardness and tensile strength decreased along the built direction, while the elongation increased from the bottom to the top of the billet. After heat treatments, Vickers microhardness resulted lower of 10HV at the top of the bar compared to its bottom in contact with the hot substrate; microhardness decreased with time at constant temperature compared to the as-built. Tensile properties showed variations of 50 MPa and 1% elongation between the top and the bottom of the billet when aging was performed at 175°C for 4h; the strength and ductility gradients were reduced to 20 MPa and 0,5% respectively by increasing the aging time to 6h. Microstructure investigations performed by scanning electron microscopy confirmed the different evolution of Silicon particles and precipitated particles at different height of the bars.


2015 ◽  
Vol 781 ◽  
pp. 388-421 ◽  
Author(s):  
Jie Ren ◽  
Song Fu

Görtler vortices developed in laminar boundary layer experience remarkable changes when the flow is subjected to compressibility effects. In the present study, five $\mathit{Ma}$ numbers, covering incompressible to hypersonic flows, at $\mathit{Ma}=0.015$, 1.5, 3.0, 4.5 and 6.0 are specified to illustrate these effects. Görtler vortices in subsonic and moderate supersonic flows ($\mathit{Ma}=0.015$, 1.5 and 3.0) are governed by the conventional wall-layer mode (mode W). In hypersonic flows ($\mathit{Ma}=4.5$, 6.0), the trapped-layer mode (mode T) becomes dominant. This difference is maintained and intensifies downstream leading to different scenarios of secondary instabilities. The linear and nonlinear development of Görtler vortices which are governed by dominant modal disturbances are investigated with direct marching of the nonlinear parabolic equations. The secondary instabilities of Görtler vortices set in when the resulting streaks are adequately developed. They are studied with Floquet theory at multiple streamwise locations. The secondary perturbations become unstable downstream following the sequence of sinuous mode type I, varicose mode and sinuous mode type II, indicating an increasing threshold amplitude. Onset conditions are determined for these modes. The above three modes can each have the largest growth rate under the right conditions. In the hypersonic cases, the threshold amplitude $A(u)$ is dramatically reduced, showing the significant impact of the thermal streaks. To investigate the parametric effect of the spanwise wavenumber, three global wavenumbers ($B=0.5$, 1.0 and $2.0\times 10^{-3}$) are specified. The relationship between the dominant mode (sinuous or varicose) and the spanwise wavenumber of Görtler vortices found in incompressible flows (Li & Malik, J. Fluid Mech., vol. 297, 1995, pp. 77–100) is shown to be not fully applicable in high-speed cases. The sinuous mode becomes the most dangerous, regardless of the spanwise wavelength when $\mathit{Ma}>3.0$. The subharmonic type can be the most dangerous mode while the detuned type can be neglected, although some of the sub-dominant secondary modes reach their peak growth rates under detuned states.


Nano Energy ◽  
2019 ◽  
Vol 66 ◽  
pp. 104169 ◽  
Author(s):  
Zailei Zhang ◽  
Yu Bai ◽  
Liang Xu ◽  
Man Zhao ◽  
Mingwei Shi ◽  
...  

1988 ◽  
Vol 135 ◽  
Author(s):  
T. Sekine ◽  
C. Julien ◽  
M. Jouanne ◽  
M. Weber ◽  
M. Balkanski

AbstractRaman scattering and IR absorption were studied in Li-intercalated MoS2 at room temperature. After intercalation, new Raman peaks were observed at low-frequency sides of the high-frequency original Raman peaks and around a rigid-layer mode. This fact indicates the formation of superlattice structure along the c-axis. An intercalation mode in which Li atoms vibrate strongly against the host lattice was observed at about 205 cm−1. Two new broad bands grow in the high-frequency region as the concentration of Li increases. The corresponding peaks were observed by IR absorption. They appears to be caused by vibrations of substitutional defects, in which the Li atoms have substituted for Mo atoms in the host lattice.


1980 ◽  
Vol 19 (2) ◽  
pp. 371-372 ◽  
Author(s):  
Toru Kanaji ◽  
Yōichi Taki ◽  
Toshio Urano
Keyword(s):  

RSC Advances ◽  
2016 ◽  
Vol 6 (80) ◽  
pp. 76933-76937 ◽  
Author(s):  
Tiantian Gao ◽  
Bo Wang ◽  
Haitao Fang ◽  
Chunyu Liu ◽  
Lei Wang ◽  
...  

LVP was added to LCO through a “layer to layer” mode to make a composite cathode and to reduce the potential of LCO during the over-discharge process.


Sign in / Sign up

Export Citation Format

Share Document