Temperature coefficient of power (Pmax) of field aged PV modules: impact on performance ratio and degradation rate determinations

2017 ◽  
Author(s):  
Telia Curtis ◽  
Farrukh Mahmood ◽  
Hatif Majeed ◽  
Haider Agha ◽  
Saddam Ali ◽  
...  
Keyword(s):  
Temperature Coefficient ◽  
Degradation Rate ◽  
Performance Ratio ◽  
Pv Modules

scholarly journals Photovoltaic modules evaluation and dry-season energy yield prediction model for NEM in Malaysia

PLoS ONE ◽  
2020 ◽  
Vol 15 (11) ◽  
pp. e0241927
Author(s):  
Syed Zahurul Islam ◽  
Mohammad Lutfi Othman ◽  
Muhammad Saufi ◽  
Rosli Omar ◽  
Arash Toudeshki ◽  
...  
Keyword(s):  
Temperature Coefficient ◽  
Output Power ◽  
Power Efficiency ◽  
Crystalline Silicon ◽  
Dry Season ◽  
Performance Ratio ◽  
Coefficient Of Determination ◽  
Energy Yield ◽  
Net Energy ◽  
Pv Modules

This study analyzes the performance of two PV modules, amorphous silicon (a-Si) and crystalline silicon (c-Si) and predicts energy yield, which can be seen as facilitation to achieve the target of 35% reduction of greenhouse gases emission by 2030. Malaysia Energy Commission recommends crystalline PV modules for net energy metering (NEM), but the climate regime is a concern for output power and efficiency. Based on rainfall and irradiance data, this study aims to categorize the climate of peninsular Malaysia into rainy and dry seasons; and then the performance of the two modules are evaluated under the dry season. A new mathematical model is developed to predict energy yield and the results are validated through experimental and systematic error analysis. The parameters are collected using a self-developed ZigBeePRO-based wireless system with the rate of 3 samples/min over a period of five days. The results unveil that efficiency is inversely proportional to the irradiance due to negative temperature coefficient for crystalline modules. For this phenomenon, efficiency of c-Si (9.8%) is found always higher than a-Si (3.5%). However, a-Si shows better shadow tolerance compared to c-Si, observed from a lesser decrease rate in efficiency of the former with the increase in irradiance. Due to better spectrum response and temperature coefficient, a-Si shows greater performance on output power efficiency (OPE), performance ratio (PR), and yield factor. From the regression analysis, it is found that the coefficient of determination (R2) is between 0.7179 and 0.9611. The energy from the proposed model indicates that a-Si yields 15.07% higher kWh than c-Si when luminance for recorded days is 70% medium and 30% high. This study is important to determine the highest percentage of energy yield and to get faster NEM payback period, where as of now, there is no such model to indicate seasonal energy yield in Malaysia.

scholarly journals Photovoltaic Degradation Rate Affected by Different Weather Conditions: A Case Study Based on PV Systems in the UK and Australia

Electronics ◽  
2020 ◽  
Vol 9 (4) ◽  
pp. 650 ◽  
Author(s):  
Mahmoud Dhimish ◽  
Abdullah Alrashidi
Keyword(s):  
Degradation Rate ◽  
Rapid Change ◽  
Weather Conditions ◽  
Exposure Period ◽  
Performance Ratio ◽  
Cold Weather ◽  
Pv Systems ◽  
Pv Modules ◽  
Hot Weather ◽  
The Uk

This article presents the analysis of degradation rate over 10 years (2008 to 2017) for six different photovoltaic (PV) sites located in the United Kingdom (mainly affected by cold weather conditions) and Australia (PV affected by hot weather conditions). The analysis of the degradation rate was carried out using the year-on-year (YOY) degradation technique. It was found that the degradation rate in the UK systems varies from −1.05% and −1.16%/year. Whereas a higher degradation ranging from −1.35% to −1.46%/year is observed for the PV systems installed in Australia. Additionally, it was found that in the Australian PV systems multiple faulty PV bypass diodes are present due to the rapid change in the ambient temperature and uneven solar irradiance levels influencing the PV modules. However, in cold weather conditions (such as in the Northern UK) none of the bypass diodes were damaged over the considered PV exposure period. Furthermore, the number of PV hot spots have also been observed, where it was found that in the UK-based PV systems the number of hot spotted PV modules are less than those found in the Australian systems. Finally, the analysis of the monthly performance ratio (PR) was calculated. It was found that the mean monthly PR is equal to 88.81% and 86.35% for PV systems installed in the UK and Australia, respectively.

Artificial intelligence technique for estimating PV modules performance ratio under outdoor operating conditions

2018 ◽  
Vol 10 (5) ◽  
pp. 053505 ◽  
Author(s):  
Alain K. Tossa ◽  
Y. M. Soro ◽  
Y. Coulibaly ◽  
Y. Azoumah ◽  
Anne Migan-Dubois ◽  
...  
Keyword(s):  
Artificial Intelligence ◽  
Operating Conditions ◽  
Performance Ratio ◽  
Artificial Intelligence Technique ◽  
Pv Modules ◽  
Intelligence Technique

scholarly journals Performance Evaluation of 100kWp Roof-top Grid-connected PV System installed in Northern India

2019 ◽  
Vol 8 (3) ◽  
pp. 8441-8444 ◽  
Keyword(s):  
Degradation Rate ◽  
Capacity Utilization ◽  
Plant Performance ◽  
Performance Ratio ◽  
Energy Output ◽  
System Efficiency ◽  
Pv System ◽  
Utilization Factor ◽  
Northern India ◽  
Efficiency Performance

The performance of 100 kWp roof-top grid-connected PV system was evaluated. The plant was installed at PGDM building in Sharda University, Greater Noida in northern India. The plant was monitored from March 2018 to February 2019. Performance parameters such as system efficiency, performance ratio, capacity utilization factor, and degradation rate were obtained. The plant performance result was compared with the estimated results obtained from SAM and PVsyst software. The total annual energy output was found to be 16426 kWh. The annual average system efficiency and capacity utilization factor of the plant was found to be 15.62 % and 14.72 % respectively. The annual performance ratio and annual degradation rate were found to be 76% and 1.28%/year respectively. The annual performance ratio obtained from SAM and PVsyst was found to be 78% and 82% respectively. It was noticed that the measured performance ratio was highly relative with the one obtained from SAM software.

scholarly journals Characteristic Analysis of Photovoltaic On-Grid System In Tropical Region For Weather-Corrected Performance Ratio Calculation Method Implementation

2018 ◽  
Vol 67 ◽  
pp. 01025
Author(s):  
Erfan Syahputra ◽  
Rio Agustian Fajarin ◽  
Eko Adhi Setiawan
Keyword(s):  
Temperature Coefficient ◽  
Calculation Method ◽  
Tropical Climate ◽  
Photovoltaic System ◽  
Performance Ratio ◽  
Ratio Method ◽  
Photovoltaic Systems ◽  
Subtropical Climate ◽  
Operating Condition ◽  
Real Operating Condition

Indonesia has different weather factors than the subtropical climate that influences the performance indicators of photovoltaic systems. One of them is performance ratio that is affected by temperature factors. NREL proposes calculation method of Weather-Corrected Performance Ratio for correcting factors (temperature) in calculation performance ratio of photovoltaic systems. However, the implementation of this method in real operating condition of photovoltaic system especially in the tropics, has not received special attention. In addition, temperature coefficient of power photovoltaic (δ) in Standard Test Condition, is used in the calculation method may be different in real operating condition. This study was conducted to determine the effects of weather-corrected performance ratio method and to know characteristic of temperature coefficient of power photovoltaic (δ) as factors in of weather-corrected performance ratio method, in real operating condition especially in tropics. Through analysis photovoltaic system data from the data logger it is found that the range values of weather-corrected performance ratio are greater than conventional methods, with a maximum increase of 2.43%. Moreover it is found that because average temperature of tropical climate is higher than subtropical climate, it makes the percentage of power decrease to rise in temperature (δ) in tropical climate is higher than subtropical climate.

scholarly journals Global Climate Data Processing and Mapping of Degradation Mechanisms and Degradation Rates of PV Modules

Energies ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4749 ◽  
Author(s):  
Julián Ascencio-Vásquez ◽  
Ismail Kaaya ◽  
Kristijan Brecl ◽  
Karl-Anders Weiss ◽  
Marko Topič
Keyword(s):  
Degradation Rate ◽  
Global Climate ◽  
Global Scale ◽  
Degradation Mechanisms ◽  
Climate Data ◽  
Pv Systems ◽  
Degradation Rates ◽  
Pv Modules ◽  
Long Term Performance ◽  
Term Performance

Photovoltaic (PV) systems are the cheapest source of electricity in sunny locations and nearly all European countries. However, the fast deployment of PV systems around the world is bringing uncertainty to the PV community in terms of the reliability and long-term performance of PV modules under different climatic stresses, such as irradiation, temperature changes, and humidity. Methodologies and models to estimate the annual degradation rates of PV modules have been studied in the past, yet, an evaluation of the issue at global scale has not been addressed so far. Hereby, we process the ERA5 climate re-analysis dataset to extract and model the climatic stresses necessary for the calculation of degradation rates. These stresses are then applied to evaluate three degradation mechanisms (hydrolysis-degradation, thermomechanical-degradation, and photo- degradation) and the total degradation rate of PV modules due to the combination of temperature, humidity, and ultraviolet irradiation. Further on, spatial distribution of the degradation rates worldwide is computed and discussed proving direct correlation with the Köppen-Geiger-Photovoltaic climate zones, showing that the typical value considered for the degradation rate on PV design and manufacturer warranties (i.e., 0.5%/a) can vary ± 0.3%/a in the temperate zones of Europe and rise up to 1.5%/a globally. The mapping of degradation mechanisms and total degradation rates is provided for a monocrystalline silicon PV module. Additionally, we analyze the temporal evolution of degradation rates, where a global degradation rate is introduced and its dependence on global ambient temperature demonstrated. Finally, the categorization of degradation rates is made for Europe and worldwide to facilitate the understanding of the climatic stresses.

scholarly journals Performance Analysis of a Hypothetical 1-Hectare PV Plant in the Benguela Region. The First Year of Operation.

2021 ◽  
Vol 2 (2) ◽  
pp. 32-39
Author(s):  
Carlos Pinho ◽  
Luís Ramos ◽  
Zenaida Mourão
Keyword(s):  
Average Energy ◽  
Alternate Current ◽  
Total Surface Area ◽  
Performance Ratio ◽  
Electricity Production ◽  
Emissions Reduction ◽  
First Year ◽  
Pv System ◽  
Energy And Exergy ◽  
Pv Modules

The presents study evaluates the performance of a hypothetical 1-hectare solar photovoltaic (PV) plant located in the Baía Azul Beach, in Benguela, Angola. The first year performance of the plant composed by 2,784 DuoMax 365 PV modules from Trina Solar Company was evaluated by means of the VelaSolaris Polysum software package. The total surface area of the PV modules was of 5,456.64 m2. The annual alternate current electricity production was of 1,511.70 MWh allowing a total of 710.47 tCO2 of CO2 emissions reduction and a performance ratio of 72.8 %. The annual average energy and exergy efficiencies of the PV system were respectively of of 14.3 % and 14.7 %.

scholarly journals An overview of commercially available Teslameters for applications in modern science and industry

ACTA IMEKO ◽  
2017 ◽  
Vol 6 (1) ◽  
pp. 43 ◽  
Author(s):  
Dragana Popovic Renella ◽  
Sasa Spasic ◽  
Sasa Dimitrijevic ◽  
Marjan Blagojevic ◽  
Radivoje S Popovic
Keyword(s):  
Magnetic Field ◽  
Temperature Coefficient ◽  
Low Frequency ◽  
Modern Science ◽  
Calibration Procedure ◽  
Magnetic Sensors ◽  
Performance Ratio ◽  
Frequency Noise ◽  
Hall Probe ◽  
Sensitive Volume

<p>The Hall-effect based Teslameters (also called Gaussmeters) are the mostly applied instruments for measuring DC and AC magnetic flux densities in modern science and industry. This paper gives an overview of commercially available Teslameters at the high-end performance level. The Teslameters have been evaluated by following characteristics that are published by suppliers: probe dimensions, magnetic field sensitive volume, accuracy, magnetic resolution, measurement range, frequency bandwidth, temperature coefficient sensitivity, and price/performance ratio.</p><p>The Teslameter that best matches the measurement needs in various application fields incorporates a 3-axis integrated Hall probe, analog electronics based on the spinning-current technique, an analog-to-digital converter, an embedded computer, and a touch-screen display. The 3-axis Hall probe is a single silicon chip integrating both horizontal and vertical Hall magnetic sensors and a temperature sensor. The spinning-current eliminates most of the Hall probe offset, low-frequency noise, and the planar Hall voltage. The errors due to the Hall sensor non-linearity and the variations in the probe and electronics temperatures are eliminated by a calibration procedure. The errors due to the angular imperfections of the Hall probe are eliminated by a calibration of the sensitivity tensor of the probe. This Teslameter can measure magnetic field vectors from about 100 nT to 30 T, with the spatial resolution of 100 µm, magnetic resolution ±2 ppm of the range, the accuracy 0.002 % of the range, a temperature coefficient less than 5 ppm/°C, and angular errors less than 0.1°.</p>

scholarly journals Performance analysis of a hypothetical 1-hectare PV plant in the Benguela region. The first year of operation.

2021 ◽  
Vol 2 (2) ◽  
pp. 32-39
Author(s):  
Carlos Pinho ◽  
Luís Ramos ◽  
Zenaida Mourão
Keyword(s):  
Average Energy ◽  
Alternate Current ◽  
Total Surface Area ◽  
Performance Ratio ◽  
Electricity Production ◽  
Emissions Reduction ◽  
First Year ◽  
Pv System ◽  
Energy And Exergy ◽  
Pv Modules

The presents study evaluates the performance of a hypothetical 1-hectare solar photovoltaic (PV) plant located in the Baía Azul Beach, in Benguela, Angola. The first year performance of the plant composed by 2,784 DuoMax 365 PV modules from Trina Solar Company was evaluated by means of the VelaSolaris Polysum software package. The total surface area of the PV modules was of 5,456.64 m2. The annual alternate current electricity production was of 1,511.70 MWh allowing a total of 710.47 tCO2 of CO2 emissions reduction and a performance ratio of 72.8 %. The annual average energy and exergy efficiencies of the PV system were respectively of of 14.3 % and 14.7 %.

scholarly journals Supercapacitor based PV measurement technique − quality assessment with poly-Si PV modules at IIEST, Kolkata

2019 ◽  
Vol 10 ◽  
pp. 9
Author(s):  
Sudipta Basu Pal ◽  
Rahul Kumar ◽  
Konika Das Bhattacharya ◽  
Dipankar Mukherjee ◽  
Debkalyan Paul
Keyword(s):  
Fill Factor ◽  
Quality Parameters ◽  
Performance Ratio ◽  
Electrical Parameters ◽  
Pv Panel ◽  
Pv Modules ◽  
Cell Modules ◽  
Commercial Testing ◽  
And Performance ◽  
First Time

Supercapacitors have been used for the first time as load to PV cell/modules for characterizing their behavior. In this paper, a novel and essentially simple design of a V–I plotter is attempted with a bank of super capacitors (SC) as the load to the PV modules of varying capacities. The distinct advantages of the SC's over the erstwhile capacitors have been comparatively experimented. Finally, an elaborate regression analysis (RA) of principal electrical parameters have yielded consistently high values exceeding 0.993 experimental evaluation of quality parameters like fill-factor (FF) and performance ratio (PR) have yielded a range of 70–79% while PR values frequently ranges from 90% to 99%. Suitability of poly-Si PV modules at the level of PV panel configurations have been ascertained through experimental estimate of series and parallel relative power loss (RPL) values. Typical values below 2% obtained for widely varying climatic level is also a quality indicator for the new metrology in question. Such a prototype I–V plotter is expected to be duly considered for commercial testing applications in PV industries.

Sign in / Sign up

Export Citation Format

Share Document