Analysis on frequency response of trans-impedance amplifier (TIA) for signal-to-noise ratio (SNR) enhancement in optical signal detection system using lock-in amplifier (LIA)

2017 ◽  
Author(s):  
Ji-Hoon Kim ◽  
Su-Jin Jeon ◽  
Myung-Gi Ji ◽  
Jun-Hee Park ◽  
Young-Wan Choi
Keyword(s):  
Signal Detection ◽  
Frequency Response ◽  
Detection System ◽  
Signal To Noise Ratio ◽  
Optical Signal ◽  
Signal To Noise ◽  
Noise Ratio ◽  
Lock In

scholarly journals Integrated in-band optical signal-to-noise ratio monitor implemented on SOI platform

2012 ◽  
Vol 20 (8) ◽  
pp. 8512 ◽  
Author(s):  
Lianxi Jia ◽  
Junfeng Song ◽  
Tsung-Yang Liow ◽  
Qing Fang ◽  
Mingbin Yu ◽  
...  
Keyword(s):  
Signal To Noise Ratio ◽  
Optical Signal ◽  
Signal To Noise ◽  
Noise Ratio

Weak Signal Detection System Based on Lock-in Amplifier Technology

2013 ◽  
Vol 389 ◽  
pp. 489-493
Author(s):  
Yong Lv ◽  
Chun Hui Niu ◽  
Yue Qiang Li ◽  
Qing Shan Chen ◽  
Xiao Ying Li ◽  
...  
Keyword(s):  
Signal Detection ◽  
Detection System ◽  
Signal To Noise Ratio ◽  
Weak Signal ◽  
Weak Signal Detection ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Low Pass ◽  
Phase Sensitive ◽  
Lock In

In order to detect the weak signal deeply buried in the noise, a weak signal detection system based on lock-in amplifier is proposed. The system includes the preamplifier circuit, active low pass filter circuit, AC amplifying circuit and phase sensitive demodulation circuit. Test results show that it can greatly increase the signal-to-noise ratio (SNR) up to 12.7db.

scholarly journals Design of an Indigenised Electronic Lock-In Amplifier

2000 ◽  
Vol 23 (1) ◽  
pp. 53-60
Author(s):  
Umesh Kumar
Keyword(s):  
Narrow Band ◽  
Signal To Noise Ratio ◽  
Broad Band ◽  
Power Line ◽  
Frequency Drift ◽  
Noise Power ◽  
Signal To Noise ◽  
Band Noise ◽  
Noise Ratio ◽  
Lock In

An indigenised lock-in amplifier is designed that enables the accurate measurement of signals contaminated by broad-band noise, power-line pick-up, frequency drift, or other sources of interference. It does this by means of an extremely narrow band detector which has the centre of its passband locked to the frequency of the signal to be measured. Large improvements in signal-to-noise ratio are achieved.

A constrained minimum power adaptive beamformer with time‐varying adaptation rate

Geophysics ◽  
1979 ◽  
Vol 44 (6) ◽  
pp. 1088-1096 ◽  
Author(s):  
Wen‐Wu Shen
Keyword(s):  
Adaptive Algorithm ◽  
Detection System ◽  
Signal To Noise Ratio ◽  
High Amplitude ◽  
Research Station ◽  
Power Performance ◽  
Signal To Noise ◽  
Filter Output ◽  
Short Period ◽  
Noise Ratio

A linear adaptive algorithm was developed for array beamforming purposes. The design goal for the algorithm is to minimize the squared filter output subject to filter constraints which allow energy propagating from the array steering direction to pass without being distorted. The adaptive filter coefficients were initialized to satisfy the constraints which were preserved during the iterations. The adaptation rate is inversely varied with filter output and total input channel power. Performance of the algorithm was studied using the recorded short‐period array data from the Korean Seismic Research Station. Processed were a high‐amplitude signal from Kamchatka, a medium‐amplitude signal from eastern Kazakh, and a number of low‐amplitude signals from central Eurasia. Results of signal‐to‐noise ratio gain relative to a conventional beamformer among the events tested were consistent and were in the range of 4.5 to 6.5 dB in the wide passband. Much better signal‐to‐noise ratio improvement was obtained in the low‐frequency passband. The adaptive algorithm was programmed in the real‐time mode and can be implemented in a front‐end detection system.

Sign in / Sign up

Export Citation Format

Share Document