Thermal conductivity characterization of in-situ fabricated polysilicon nanowires for uncooled thermoelectric infrared detectors

2015 ◽  
Author(s):  
Mohammad J. Modarres-Zadeh ◽  
Nahida Akhter ◽  
Ronald Hellmer ◽  
Michael Aragon ◽  
Reza Abdolvand
Keyword(s):  
Thermal Conductivity ◽  
Infrared Detectors

Preparation and Characterization of In Situ Nanocomposites of Graphene Nanosheets/Polyurethane

2019 ◽  
Vol 814 ◽  
pp. 90-95 ◽  
Author(s):  
Guang Lei Lv ◽  
Yuan Yuan Li ◽  
Chen Fei ◽  
Zhi Hao Shan ◽  
Jing Gan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Tensile Strength ◽  
Graphene Nanosheets ◽  
Graphene Sheets ◽  
Microstructural Properties ◽  
Wear Performance ◽  
Polyurethane Composites

Graphene nanosheets/polyurethane (GNS/PU) was prepared in situ by polymerization technique for the manufacture of PU safety shoes soles. The graphene nanosheets/polyurethane composites were characterized for their mechanical properties, thermal conductivity and abrasion resistance, and comparison is made with those of the neat polyurethane. The microstructural properties of GNS/PU were characterized by SEM. The results show that with the increase of the amount of graphene within the range of weight-percentages analyzed, the tensile strength of the composites gradually increases. The tensile strength of the GNS/PU composites increased to 64.14 MPa with 2 wt% GNS, compared with 55.1 MPa for neat PU. When the graphene sheets reached 2 wt%, the abrasion volume reached 71 mm3. Compared with the pure PU, the wear performance of GNS/PU composites was significantly improved.

Studying the Progress of Sintering in Ferrous Powder Compacts by In-Situ Measuring the Thermal Conductivity

2018 ◽  
Vol 18 (2) ◽  
pp. 80-95
Author(s):  
H. Danninger ◽  
G. Leitner ◽  
Ch. Gierl-Mayer
Keyword(s):  
Thermal Conductivity ◽  
Laser Flash ◽  
Sintering Process ◽  
In Situ Characterization ◽  
Dimensional Changes ◽  
Flow Through ◽  
Powder Compacts ◽  
Good Agreement

Abstract In situ characterization of the sintering process is a difficult task, in particular for systems without pronounced dimensional changes. Dilatometry is not too helpful in those cases, and therefore other properties have to be recorded. In the present study, sintering of ferrous powder compacts was studied in situ by measuring the thermal diffusivity a using a laser flash apparatus. This property is a measure to characterise the heat flow through a material; it depends on the contact area between the particles and thus reveals their change during sintering. It is shown that the change of a during sintering of ferrous compacts is much less pronounced than in the case of cemented carbides which is not surprising when regarding the widely differing porosity changes. The results are however in good agreement with expectations when considering some experimental limitations. The trend for the thermal conductivity λ. which can be calculated from a, the specific heat and the density, is in good agreement with that found for the electrical conductivity, both properties being linked through Wiedemann-Franz’ law.

Fabrication and Characterization of Light Emitting Porous Silicon and Polymer Nanocomposites

1996 ◽  
Vol 452 ◽  
Author(s):  
S. P. Duttagupta ◽  
P. M. Fauchet ◽  
X. L. Chen ◽  
S. A. Jenekhe
Keyword(s):  
Thermal Conductivity ◽  
Porous Silicon ◽  
Room Temperature ◽  
In Situ Polymerization ◽  
Pore Filling ◽  
Light Emitting ◽  
Polymer Molecules ◽  
Fabrication And Characterization

AbstractWe report the fabrication of nanocomposites by the infiltration of polymers into porous silicon. Polymers such as polyamide, polystyrene, PMMA, and PVC were chosen because they are commonly available and have been extensively studied. The pore-filling was accomplished by either diffusion of the polymer molecules into porous silicon or in-situ polymerization of the monomer. The Vickers hardness arid the thermal conductivity of the samples were measured. There was a difference in the nanocomposite characteristics depending on whether the samples were as-anodized or had been annealed in oxygen. By infiltrating polyamide into an as-anodized sample, a 42% increase in hardness and a 24% increase in thermal conductivity were observed at room temperature, without any degradation of luminescence.

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

1973 ◽  
Vol 31 ◽  
pp. 132-133 ◽  
Author(s):  
R. E. Herfert
Keyword(s):  
Surface Characterization ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Depth Of Penetration ◽  
X Ray ◽  
The Past ◽  
Transmission Electron ◽  
Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

A very rapid in situ Kikuchi technique to determine relative crystal misorientation

1988 ◽  
Vol 46 ◽  
pp. 830-831
Author(s):  
J. I. Bennetch
Keyword(s):  
Electron Beam ◽  
Analytical Techniques ◽  
Superplastic Forming ◽  
The Other ◽  
Kikuchi Pattern ◽  
Kikuchi Line ◽  
Line Analysis

In a recent study of the superplastic forming (SPF) behavior of certain Al-Li-X alloys, the relative misorientation between adjacent (sub)grains proved to be an important parameter. It is well established that the most accurate way to determine misorientation across boundaries is by Kikuchi line analysis. However, the SPF study required the characterization of a large number of (sub)grains in each sample to be statistically meaningful, a very time-consuming task even for comparatively rapid Kikuchi analytical techniques.In order to circumvent this problem, an alternate, even more rapid in-situ Kikuchi technique was devised, eliminating the need for the developing of negatives and any subsequent measurements on photographic plates. All that is required is a double tilt low backlash goniometer capable of tilting ± 45° in one axis and ± 30° in the other axis. The procedure is as follows. While viewing the microscope screen, one merely tilts the specimen until a standard recognizable reference Kikuchi pattern is centered, making sure, at the same time, that the focused electron beam remains on the (sub)grain in question.

Coherent electron nanodiffraction from clean silver nano particles in a UHV STEM

1993 ◽  
Vol 51 ◽  
pp. 1058-1059
Author(s):  
J. Liu ◽  
M. Pan ◽  
G. E. Spinnler
Keyword(s):  
Supported Catalysts ◽  
Imaging Techniques ◽  
Nano Particles ◽  
Metal Particles ◽  
Shape Structure ◽  
Dynamical Simulations ◽  
Small Metal Particles ◽  
Extract Information

Small metal particles have peculiar chemical and physical properties as compared to bulk materials. They are especially important in catalysis since metal particles are common constituents of supported catalysts. The structural characterization of small particles is of primary importance for the understanding of structure-catalytic activity relationships. The shape and size of metal particles larger than approximately 5 nm in diameter can be determined by several imaging techniques. It is difficult, however, to deduce the shape of smaller metal particles. Coherent electron nanodiffraction (CEND) patterns from nano particles contain information about the particle size, shape, structure and defects etc. As part of an on-going program of STEM characterization of supported catalysts we report some preliminary results of CEND study of Ag nano particles, deposited in situ in a UHV STEM instrument, and compare the experimental results with full dynamical simulations in order to extract information about the shape of Ag nano particles.

Characterization of the glycoconjugates of boar testis and epididymis

Reproduction ◽  
2000 ◽  
pp. 325-335 ◽  
Author(s):  
A Calvo ◽  
LM Pastor ◽  
S Bonet ◽  
E Pinart ◽  
M Ventura
Keyword(s):  
Ricinus Communis ◽  
Lectin Histochemistry ◽  
Apical Part ◽  
Seminiferous Tubules ◽  
In Situ Characterization ◽  
Intense Staining ◽  
Terminal Galactose ◽  
Boar Spermatozoa

Lectin histochemistry was used to perform in situ characterization of the glycoconjugates present in boar testis and epididymis. Thirteen horseradish peroxidase- or digoxigenin-labelled lectins were used in samples obtained from healthy fertile boars. The acrosomes of the spermatids were stained intensely by lectins with affinity for galactose and N-acetyl-galactosamine residues, these being soybean, peanut and Ricinus communis agglutinins. Sertoli cells were stained selectively by Maackia ammurensis agglutinin. The lamina propria of seminiferous tubules showed the most intense staining with fucose-binding lectins. The Golgi area and the apical part of the principal cells of the epididymis were stained intensely with many lectins and their distribution was similar in the three zones of the epididymis. On the basis of lectin affinity, both testis and epididymis appear to have N- and O-linked glycoconjugates. Spermatozoa from different epididymal regions showed different expression of terminal galactose and N-acetyl-galactosamine. Sialic acid (specifically alpha2,3 neuraminic-5 acid) was probably incorporated into spermatozoa along the extratesticular ducts. These findings indicate that the development and maturation of boar spermatozoa are accompanied by changes in glycoconjugates. As some lectins stain cellular or extracellular compartments specifically, these lectins could be useful markers in histopathological evaluation of diseases of boar testis and epididymis.

Spectro-mechanical Characterization of Aromaticity and Maturity of Kerogens in Oil Shale at 6 nm Spatial Resolution

2018 ◽  
Author(s):  
Devon Jakob ◽  
Le Wang ◽  
Haomin Wang ◽  
Xiaoji Xu
Keyword(s):  
Spatial Resolution ◽  
Oil Shale ◽  
Infrared Imaging ◽  
Mechanical Characterization ◽  
Optical Diffraction ◽  
Chemical Compositions ◽  
Valuable Insight ◽  
Eagle Ford Shale

<p>In situ measurements of the chemical compositions and mechanical properties of kerogen help understand the formation, transformation, and utilization of organic matter in the oil shale at the nanoscale. However, the optical diffraction limit prevents attainment of nanoscale resolution using conventional spectroscopy and microscopy. Here, we utilize peak force infrared (PFIR) microscopy for multimodal characterization of kerogen in oil shale. The PFIR provides correlative infrared imaging, mechanical mapping, and broadband infrared spectroscopy capability with 6 nm spatial resolution. We observed nanoscale heterogeneity in the chemical composition, aromaticity, and maturity of the kerogens from oil shales from Eagle Ford shale play in Texas. The kerogen aromaticity positively correlates with the local mechanical moduli of the surrounding inorganic matrix, manifesting the Le Chatelier’s principle. In situ spectro-mechanical characterization of oil shale will yield valuable insight for geochemical and geomechanical modeling on the origin and transformation of kerogen in the oil shale.</p>

Characterization of Interconnect Defects Using Scanning Thermal Conductivity Microscopy

2004 ◽  
Author(s):  
H.W. Ho ◽  
J.C.H. Phang ◽  
A. Altes ◽  
L.J. Balk
Keyword(s):  
Thermal Conductivity ◽  
Integrated Circuits ◽  
Large Scale

Abstract In this paper, scanning thermal conductivity microscopy is used to characterize interconnect defects due to electromigration. Similar features are observed both in the temperature and thermal conductivity micrographs. The key advantage of the thermal conductivity mode is that specimen bias is not required. This is an important advantage for the characterization of defects in large scale integrated circuits. The thermal conductivity micrographs of extrusion, exposed and subsurface voids are presented and compared with the corresponding topography and temperature micrographs.

Sign in / Sign up

Export Citation Format

Share Document