Assessment of hemoglobin dynamics in traumatic bruises using temperature depth profiling

2013 ◽  
Author(s):  
Luka Vidovič ◽  
Matija Milanič ◽  
Boris Majaron
Keyword(s):  
Depth Profiling ◽  
Temperature Depth ◽  
Temperature Depth Profiling

Preferential Sputtering of Ni3Al Single Crystals Studied Using Atom-Probe Field-Ion Microscopy and XPS

1981 ◽  
Vol 39 ◽  
pp. 16-17
Author(s):  
M.P. Thomas ◽  
A.R. Waugh ◽  
M.J. Southon ◽  
Brian Ralph
Keyword(s):  
Single Crystals ◽  
Photoelectron Spectroscopy ◽  
Surface Composition ◽  
Depth Profiling ◽  
Analytical Techniques ◽  
Atom Probe ◽  
Probe Field ◽  
Preferential Sputtering ◽  
Argon Ion Bombardment ◽  
Argon Ion

It is well known that ion-induced sputtering from numerous multicomponent targets results in marked changes in surface composition (1). Preferential removal of one component results in surface enrichment in the less easily removed species. In this investigation, a time-of-flight atom-probe field-ion microscope A.P. together with X-ray photoelectron spectroscopy XPS have been used to monitor alterations in surface composition of Ni3Al single crystals under argon ion bombardment. The A.P. has been chosen for this investigation because of its ability using field evaporation to depth profile through a sputtered surface without the need for further ion sputtering. Incident ion energy and ion dose have been selected to reflect conditions widely used in surface analytical techniques for cleaning and depth-profiling of samples, typically 3keV and 1018 - 1020 ion m-2.

Atomic force microscopy (AFM) of the topography of silicon surfaces exposed to ion beams

1992 ◽  
Vol 50 (2) ◽  
pp. 1132-1133
Author(s):  
Mark Denker ◽  
Jennifer Wall ◽  
Mark Ray ◽  
Richard Linton
Keyword(s):  
Secondary Ion Mass Spectrometry ◽  
Incidence Angle ◽  
Ion Beam ◽  
Depth Profiling ◽  
Depth Resolution ◽  
Ion Beams ◽  
Scanning Tunneling ◽  
Tunneling Microscopy ◽  
Trace Impurities ◽  
Energy Dose

Reactive ion beams such as O2+ and Cs+ are used in Secondary Ion Mass Spectrometry (SIMS) to analyze solids for trace impurities. Primary beam properties such as energy, dose, and incidence angle can be systematically varied to optimize depth resolution versus sensitivity tradeoffs for a given SIMS depth profiling application. However, it is generally observed that the sputtering process causes surface roughening, typically represented by nanometer-sized features such as cones, pits, pyramids, and ripples. A roughened surface will degrade the depth resolution of the SIMS data. The purpose of this study is to examine the relationship of the roughness of the surface to the primary ion beam energy, dose, and incidence angle. AFM offers the ability to quantitatively probe this surface roughness. For the initial investigations, the sample chosen was <100> silicon, and the ion beam was O2+.Work to date by other researchers typically employed Scanning Tunneling Microscopy (STM) to probe the surface topography.

Surface Microstructure Evolution Upon Silicidation of Ni(Pt) and the Different Responses to Metal Etch

2013 ◽  
Author(s):  
Wentao Qin ◽  
Dorai Iyer ◽  
Jim Morgan ◽  
Carroll Casteel ◽  
Robert Watkins ◽  
...  
Keyword(s):  
Thin Film ◽  
Oxide Film ◽  
Microstructure Evolution ◽  
Depth Profiling ◽  
Surface Microstructure ◽  
The Difference ◽  
Surface Microstructures ◽  
Pt Films

Abstract Ni(5 at.%Pt ) films were silicided at a temperature below 400 °C and at 550 °C. The two silicidation temperatures had produced different responses to the subsequent metal etch. Catastrophic removal of the silicide was seen with the low silicidation temperature, while the desired etch selectivity was achieved with the high silicidation temperature. The surface microstructures developed were characterized with TEM and Auger depth profiling. The data correlate with both silicidation temperatures and ultimately the difference in the response to the metal etch. With the high silicidation temperature, there existed a thin Si-oxide film that was close to the surface and embedded with particles which contain metals. This thin film is expected to contribute significantly to the desired etch selectivity. The formation of this layer is interpreted thermodynamically.

Sign in / Sign up

Export Citation Format

Share Document