Ferroelectric ceramic and epoxy composite films as pyroelectric detectors

1994 ◽  
Author(s):  
Matthew P. Wenger ◽  
Panagiotis Blanas ◽  
R. J. Shuford ◽  
Dilip K. Das-Gupta
Keyword(s):  
Epoxy Composite ◽  
Composite Films ◽  
Ferroelectric Ceramic ◽  
Pyroelectric Detectors

Mechanical behavior and self-healing mechanism of polyurea-based double-walled microcapsule/epoxy composite films

2021 ◽  
Vol 157 ◽  
pp. 106283
Author(s):  
Yanxuan Ma ◽  
Jiatong Liu ◽  
Yingrui Zhang ◽  
Yajie Ge ◽  
Rui Wu ◽  
...  
Keyword(s):  
Mechanical Behavior ◽  
Epoxy Composite ◽  
Composite Films ◽  
Self Healing

scholarly journals Effect of Filler Nature on Chemical Resistance and Microhardness of Epoxy Composite Films

2015 ◽  
Vol 16 (3) ◽  
pp. 528-533
Author(s):  
G. Martinyuk ◽  
O. Aksimentyeva ◽  
N. Skoreiko ◽  
V. Zakordonskyi
Keyword(s):  
Mechanical Properties ◽  
Chemical Resistance ◽  
Filler Content ◽  
Epoxy Composite ◽  
Composite Films ◽  
Physical And Mechanical Properties ◽  
Epoxy Composites ◽  
Mineral Filler ◽  
Operating Characteristics ◽  
Mineral Fillers

We investigated the processes of water absorption, chemical stability and microhardness of films of epoxy composites that contained as the polymer matrix the epoxy resin UP-655 and mineral fillers: graphite, mica, aluminum oxide at their content (0 - 30 % mass). It found that introduction of mineral fillers significantly affects on all complex of operating characteristics of the films. Increase of filler content, especially mica, to 20 %, resulting in slower process and reducing the quantity of absorbed moisture by films. In the study of physical and mechanical properties of filled epoxy composites was established that the introduction of mineral filler significantly affects their microhardness, and the nature of the exposure is determined by the type and filler content.

Effects of the Fraction of PTFE and Film Thickness on Wear and Friction in an ePTFE and Epoxy Composite Solid Lubricant Coating

2005 ◽  
Author(s):  
N. L. McCook ◽  
D. L. Burris ◽  
J. R. Hanrahan ◽  
W. G. Sawyer
Keyword(s):  
Film Thickness ◽  
Epoxy Composite ◽  
Composite Films ◽  
304 Stainless Steel ◽  
Solid Lubricant Coating ◽  
Wear Rates ◽  
Wear And Friction ◽  
Pin On Disk ◽  
Composite Solid ◽  
Wear Tests

Wear tests were performed on various expanded PTFE / epoxy composite films, using a 304 stainless steel pin, in a pin on disk configuration. The density and thickness of the expanded PTFE films were varied, and the effects on friction and wear were examined. It was found that there are trends for increased wear resistance with increasing density, and increasing film thickness. Wear rates less than 10−8 mm3/Nm were calculated on some of the composite films. The film thickness range from 75–510μm and the density ranged from 0.304 to 0.904 g/cm3. The tests were run at a 5N load and 1m/s sliding speed with varying sliding distances.

Reversible Superhydrophobic–Superhydrophilic Transition of ZnO Nanorod/Epoxy Composite Films

2012 ◽  
Vol 4 (8) ◽  
pp. 3959-3964 ◽  
Author(s):  
Yan Liu ◽  
Ziyin Lin ◽  
Wei Lin ◽  
Kyoung Sik Moon ◽  
C. P. Wong
Keyword(s):  
Epoxy Composite ◽  
Composite Films ◽  
Zno Nanorod

Self-Assembly of Monolayer-Thick Alumina Particle−Epoxy Composite Films

Langmuir ◽  
2007 ◽  
Vol 23 (23) ◽  
pp. 11399-11403 ◽  
Author(s):  
Bryan R. Jackson ◽  
Xiangyuan Liu ◽  
Elizabeth F. McCandlish ◽  
Richard E. Riman
Keyword(s):  
Self Assembly ◽  
Alumina Particle ◽  
Epoxy Composite ◽  
Composite Films
Sign in / Sign up

Export Citation Format

Share Document