Determination of optical constant of diamond thin films

1992 ◽  
Author(s):  
Xuantong Ying ◽  
Yuanhua Shen ◽  
Hang Xue ◽  
Jianhai Liu ◽  
Zhongjing Xing ◽  
...  
Keyword(s):  
Thin Films ◽  
Optical Constant ◽  
Diamond Thin Films

Infrared optical constant determination of weakly absorbing dielectric thin films

1992 ◽  
Vol 31 (7) ◽  
pp. 885
Author(s):  
Jacques Mouchart ◽  
Jacqueline Begel ◽  
Claudy Clément
Keyword(s):  
Thin Films ◽  
Optical Constant ◽  
Dielectric Thin Films ◽  
Constant Determination

Optical constant determination of thin films

1988 ◽  
Vol 27 (5) ◽  
pp. 954 ◽  
Author(s):  
Mool C. Gupta
Keyword(s):  
Thin Films ◽  
Optical Constant ◽  
Constant Determination

Interactions Between Al and Cr Thin Films

1976 ◽  
Vol 34 ◽  
pp. 638-639
Author(s):  
R. M. Anderson ◽  
T. M. Reith ◽  
M. J. Sullivan ◽  
E. K. Brandis
Keyword(s):  
Thin Films ◽  
Room Temperature ◽  
Vacuum System ◽  
Processing Temperature ◽  
Diffusion Couples ◽  
Electronic Circuits ◽  
Intermetallic Formation ◽  
Si Substrates ◽  
Aluminum Silicon

Thin films of aluminum or aluminum-silicon can be used in conjunction with thin films of chromium in integrated electronic circuits. For some applications, these films exhibit undesirable reactions; in particular, intermetallic formation below 500 C must be inhibited or prevented. The Al films, being the principal current carriers in interconnective metal applications, are usually much thicker than the Cr; so one might expect Al-rich intermetallics to form when the processing temperature goes out of control. Unfortunately, the JCPDS and the literature do not contain enough data on the Al-rich phases CrAl7 and Cr2Al11, and the determination of these data was a secondary aim of this work.To define a matrix of Cr-Al diffusion couples, Cr-Al films were deposited with two sets of variables: Al or Al-Si, and broken vacuum or single pumpdown. All films were deposited on 2-1/4-inch thermally oxidized Si substrates. A 500-Å layer of Cr was deposited at 120 Å/min on substrates at room temperature, in a vacuum system that had been pumped to 2 x 10-6 Torr. Then, with or without vacuum break, a 1000-Å layer of Al or Al-Si was deposited at 35 Å/s, with the substrates still at room temperature.

Determination of Stoichiometry of GaAs Component in (Gaas)Ge Epitaxially Grown Thin Films by Electron Microprobe X-Ray Analysis

1990 ◽  
Vol 48 (2) ◽  
pp. 264-265
Author(s):  
D. R. Liu ◽  
S. S. Shinozaki ◽  
R. J. Baird
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Monte Carlo Simulation ◽  
Monte Carlo ◽  
Compound Semiconductors ◽  
Energy Dispersive Analysis ◽  
X Ray ◽  
Metastable Alloys ◽  
Lower Voltage

The epitaxially grown (GaAs)Ge thin film has been arousing much interest because it is one of metastable alloys of III-V compound semiconductors with germanium and a possible candidate in optoelectronic applications. It is important to be able to accurately determine the composition of the film, particularly whether or not the GaAs component is in stoichiometry, but x-ray energy dispersive analysis (EDS) cannot meet this need. The thickness of the film is usually about 0.5-1.5 μm. If Kα peaks are used for quantification, the accelerating voltage must be more than 10 kV in order for these peaks to be excited. Under this voltage, the generation depth of x-ray photons approaches 1 μm, as evidenced by a Monte Carlo simulation and actual x-ray intensity measurement as discussed below. If a lower voltage is used to reduce the generation depth, their L peaks have to be used. But these L peaks actually are merged as one big hump simply because the atomic numbers of these three elements are relatively small and close together, and the EDS energy resolution is limited.

Sign in / Sign up

Export Citation Format

Share Document