Deep trench plasma etching of single crystal silicon using SF6/O2 gas mixtures

1992 ◽  
Vol 10 (3) ◽  
pp. 1105 ◽  
Author(s):  
Christopher P. D’Emic
Keyword(s):  
Single Crystal ◽  
Plasma Etching ◽  
Single Crystal Silicon ◽  
Gas Mixtures ◽  
Crystal Silicon ◽  
Deep Trench

A Study on the Damage Layer Removal of Single-Crystal Silicon Wafer After Atmospheric-Pressure Plasma Etching

2020 ◽  
Vol 8 (2) ◽  
Author(s):  
Weijia Guo ◽  
Senthil Kumar Anantharajan ◽  
Xinquan Zhang ◽  
Hui Deng
Keyword(s):  
Single Crystal ◽  
Plasma Etching ◽  
Photoelectron Spectroscopy ◽  
Atmospheric Pressure ◽  
Single Crystal Silicon ◽  
Atmospheric Pressure Plasma ◽  
Etching Process ◽  
Wafer Surface ◽  
Etching Time ◽  
Crystal Silicon

Abstract In this study, atmospheric-pressure (AP) plasma generated using He/O2/CF4 mixture as feed gas was used to etch the single-crystal silicon (100) wafer and the characteristics of the etched surface were investigated. The wafer morphology and surface elemental composition were analyzed using scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS), respectively. The XPS results reveal that the fluorine element will be deposited on the wafer surface during the etching process when oxygen was not introduced as the feed gas. By detecting the energy and intensity of emitted particles, optical emission spectroscopy (OES) is used to identify the radicals in plasma. The fluorocarbon radicals generated during CF4 plasma ionization can form carbon fluoride polymer, which is considered as one factor to suppress the etching process. The roughness was measured to be changed with the increase in the etching time. The surface appears to be rougher at first when the plasma etching occurred on the subsurface damaged (SSD) layer, and the subsurface cracks would show on the surface after a short-time etching. After the damaged layer was fully removed, etching resulted in the formation of square-opening etching pits. During extended etching, the individual etching pits grew up and coalesced with one another; this coalescence provided an improved surface roughness. This study explains the AP plasma etching mechanism, and the formation of anisotropic surface etching pits at a microscale level for promoting the micromachining process.

Semi-automatic, volume production of silicon solar cells

1987 ◽  
Vol 65 (8) ◽  
pp. 892-896 ◽  
Author(s):  
R. E. Thomas ◽  
C. E. Norman ◽  
S. Varma ◽  
G. Schwartz ◽  
E. M. Absi
Keyword(s):  
Solar Cells ◽  
Single Crystal ◽  
Plasma Etching ◽  
Low Cost ◽  
Single Crystal Silicon ◽  
High Yield ◽  
Silicon Solar Cells ◽  
Crystal Silicon ◽  
Volume Production ◽  
P Type

A low-cost, high-yield technology for producing single-crystal silicon solar cells at high volumes, and suitable for export to developing countries, is described. The process begins with 100 mm diameter as-sawn single-crystal p-type wafers with one primary flat. Processing steps include etching and surface texturization, gaseous-source diffusion, plasma etching, and contacting via screen printing. The necessary adaptations of such standard processes as diffusion and plasma etching to solar-cell production are detailed. New process developments include a high-throughput surface-texturization technique, and automatic printing and firing of cell contacts.The technology, coupled with automated equipment developed specifically for the purpose, results in solar cells with an average efficiency greater than 12%, a yield exceeding 95%, a tight statistical spread on parameters, and a wide tolerance to starting substrates (including the first 100 mm diameter wafers made in Canada). It is shown that with minor modifications, the present single shift 500 kWp (kilowatt peak) per year capacity technology can be readily expanded to 1 MWp per year, adapted to square and polycrystalline substrates, and efficiencies increased above 13%.

Single-Crystal Silicon Etching Characteristics Using Excimer Laser Cℓ2 GAS

1983 ◽  
Vol 29 ◽  
Author(s):  
T. Arikado ◽  
M. Sekine ◽  
H. Okano ◽  
Y. Horiike
Keyword(s):  
Single Crystal ◽  
Gas Phase ◽  
Excimer Laser ◽  
Plasma Etching ◽  
Etch Rate ◽  
Single Crystal Silicon ◽  
Silicon Etching ◽  
Crystal Silicon ◽  
Direct Irradiation ◽  
P Type

ABSTRACTSingle-crystal Si etching characteristics using an excimer laser (308 nm, XeCℓ) in the Cℓ2 gas have been studied. In lightly doped n-type and p-type Si, the etch rate of (100) is higher than that of (111), thus the (111) sidewall appears clearly for the irradiation to (100), while both orientations show almost the same etch rates in n+-doped Si. The n-type Si is etched spontaneously even by photo-dissociated Cℓ radicals generated in the gas phase, but no p-type Si etching occurs without direct irradiation. In addition, both types of etch rate-dependence on sheet resistance demonstrate that the number of electrons in the conduction band plays an essential role in the Si etching. This fact supports the field-assisted mechanism in the plasma etching proposed by Winters.

Analysis of Silicon-On-Insulator Structures Formed By Oxygen Ion Implantation

1985 ◽  
Vol 43 ◽  
pp. 300-301
Author(s):  
N. Lewis ◽  
E. L. Hall ◽  
A. Mogro-Campero ◽  
R. P. Love
Keyword(s):  
Ion Implantation ◽  
Single Crystal ◽  
Single Crystal Silicon ◽  
Silicon Layer ◽  
Device Fabrication ◽  
Silicon On Insulator ◽  
High Dose ◽  
Crystal Silicon ◽  
Oxygen Ion ◽  
Oxygen Ion Implantation

The formation of buried oxide structures in single crystal silicon by high-dose oxygen ion implantation has received considerable attention recently for applications in advanced electronic device fabrication. This process is performed in a vacuum, and under the proper implantation conditions results in a silicon-on-insulator (SOI) structure with a top single crystal silicon layer on an amorphous silicon dioxide layer. The top Si layer has the same orientation as the silicon substrate. The quality of the outermost portion of the Si top layer is important in device fabrication since it either can be used directly to build devices, or epitaxial Si may be grown on this layer. Therefore, careful characterization of the results of the ion implantation process is essential.

Sign in / Sign up

Export Citation Format

Share Document