scholarly journals Development of Process Induced Residual Stress During Flow Forming of Tubular 15-5 Martensitic Stainless Steel

2017 ◽  
Author(s):  
Saber Khayatzadeh ◽  
Shanmukha Rao Moturu ◽  
Joe F. Kelleher ◽  
Salah Rahimi
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Neutron Diffraction ◽  
Wall Thickness ◽  
Hole Drilling ◽  
Forming Process ◽  
Flow Forming ◽  
Stress Components ◽  
Axial Residual Stress ◽  
Original Part

Flow forming is a near net shape process for manufacturing of dimensionally accurate hollow components such as shaft in gas turbines, that is currently at its development stage for aerospace industry. The process has several advantages such as reducing material wastage, extremely fast manufacturing time, and eliminating extra manufacturing processes such as machining. Due to the nature of this complicated cold deformation process, significant magnitude of residual stress is introduced into the component. Understanding the magnitude and distribution of residual stress is essential to tailor the flow forming process to achieve parts within dimensional tolerances and desired mechanical properties. The present research is aiming to explore the generation and evolution of residual stress at various stages of flow forming process in a tubular component made from martensitic 15Cr-5Ni stainless steel, using different techniques of neutron scattering, x-ray diffraction (XRD) and hole-drilling based on electronic speckle pattern interferometry (ESPI). Residual stress measurements were carried out in preformed and flow formed components at surface, near-surface and in the bulk of components using XRD, ESPI based hole-drilling and neutron diffraction techniques. These measurements were conducted at different levels of reduction in the thickness of the original part (i.e. after 20% and 40%), by applying identical forming parameters for all samples. The XRD results show significant change in hoop and axial residual stress levels with a reduction in the wall thickness. This is more pronounced for the axial component where the average stress switches from relatively high tensile (∼ 450MPa) in the original part to significant compressive stress (∼ −600MPa) in the formed part, after 20% of reduction. The bulk residual stress components measured in the middle of thickness of the parts, using neutron scattering, show a general increase in the magnitude of residual stress by higher level of deformation (i.e. reduction in the wall thickness). The measured bulk stress components through the thickness were tuned to tensile after reducing the wall thickness by 40%. The results of XRD and neutron diffraction stress measurements suggest that the residual stress along the length of the samples (i.e. axial direction) is consistent with ±800 MPa and ±400 MPa after 20% and 40% reduction by forming process, respectively. The results of ESPI based hole-drilling show tensile hoop residual stress (≈600 MPa) and an abrupt fluctuation (i.e. tension-compressive-tension) in the axial residual stress near the surface of the part following flow forming. The stresses measured by ESPI based hole-drilling are complementary to the results of the XRD on surface and neutron diffraction in the bulk to reconstruct the residual stress profile form the surface through to the bulk.

Non-Destructive Measurement of Residual Stresses in U-0.8 WT% Ti by Neutron Diffraction

1989 ◽  
Vol 166 ◽  
Author(s):  
A. Salinas-Rodriguez ◽  
J.H. Root ◽  
T.M. Holden ◽  
S.R. Macewen ◽  
G.M. Ludtka
Keyword(s):  
Residual Stress ◽  
Neutron Diffraction ◽  
Residual Stresses ◽  
Wall Thickness ◽  
Radial Stress ◽  
Biaxial Stress ◽  
Axial Residual Stress ◽  
Residual Strains ◽  
The Difference ◽  
Hoop Stresses

ABSTRACTThe macroscopic residual stress distribution in γ-quenched and stress levelled U-0.8wt% Ti alloy tubes was studied using neutron diffraction techniques. Residual strains were evaluated from the difference in d-spacings measured in the tubes and in small reference samples machined from each tube. Residual stresses were calculated with the isotropic bulk values of the elastic constants for polycrystalline α-U. Quenching from the γ field resulted in a nearly equi-biaxial stress state at every point across the wall thickness of the tube. The magnitude of the radial stress was very small compared with that of the axial and hoop stresses which were compressive at the surfaces and tensile in the interior. Stress levelling relieved almost completely the hoop residual stress without affecting the radial stress. The axial residual stress becomes tensile through the wall thickness and remains constant at about 20% of its magnitude in the as-quenched condition.

Residual Stress Evaluation of Ni Based Weld Metal Using Neutron Diffraction Method

2006 ◽  
Vol 524-525 ◽  
pp. 697-702 ◽  
Author(s):  
Shinobu Okido ◽  
Hiroshi Suzuki ◽  
K. Saito
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Neutron Diffraction ◽  
Weld Metal ◽  
Diffraction Method ◽  
Fem Analysis ◽  
Butt Weld ◽  
Stress Evaluation ◽  
Neutron Diffraction Method

Residual stress generated in Type-316 austenitic stainless steel butt-weld jointed by Inconel-182 was measured using a neutron diffraction method and compared with values calculated using FEM analysis. The measured values of Type-316 austenitic stainless steel as base material agreed well with the calculated ones. The diffraction had high intensity and a sharp profile in the base metal. However, it was difficult to measure the residual stress at the weld metal due to very weak diffraction intensities. This phenomenon was caused by the texture in the weld material generated during the weld procedure. As a result, this texture induced an inaccurate evaluation of the residual stress. Procedures for residual stress evaluation to solve this textured material problem are discussed in this paper. As a method for stress evaluation, the measured strains obtained from a different diffraction plane with strong intensity were modified with the ratio of the individual elastic constant. The values of residual stress obtained using this method were almost the same as those of the standard method using Hooke’s law. Also, these residual stress values agreed roughly with those from the FEM analysis. This evaluation method is effective for measured samples with a strong texture like Ni-based weld metal.

Estimation of Residual Stress in Cold Rolled Iron-Disks Using Magnetic and Ultrasonic Methods and Neutron Diffraction Technique

1994 ◽  
Vol 376 ◽  
Author(s):  
V.L. Aksenov ◽  
A.M. Balagurov ◽  
G.D Bokuchava ◽  
J. Schreiber ◽  
Yu.V. Taran Frank
Keyword(s):  
Residual Stress ◽  
Neutron Diffraction ◽  
Sheet Metal ◽  
Diffraction Method ◽  
Calibration Procedure ◽  
Rolled Sheet ◽  
Forming Process ◽  
Practical Applications ◽  
Ultrasonic Methods ◽  
Cold Rolled

ABSTRACTVariation of internal stress states in cold rolled sheet metal can essentially influence the result of forming processes. Therefore it is important to control the forming process by a practicable in line testing method. For this purpose magnetic and ultrasonic nondestructive methods are available. However, it is necessary to calibrate these techniques. This paper describes a first step of such a calibration procedure making use of the neutron diffraction method. On the basis of the diffraction results an assessment of the magnetic and ultrasonic methods for the estimation of residual stress in the cold rolled iron-disks was made. Reasonable measuring concepts for practical applications to forming processes with cold rolled sheet metal are discussed.

Dual-Axis Hole-Drilling ESPI Residual Stress Measurements

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
Gary S. Schajer ◽  
Michael Steinzig
Keyword(s):  
Residual Stress ◽  
Measurement Errors ◽  
Measurement Method ◽  
Stress Measurement ◽  
Experimental Tests ◽  
Optical Data ◽  
Hole Drilling ◽  
Similar Response ◽  
Plane Normal ◽  
Stress Components

A novel dual-axis ESPI hole-drilling residual stress measurement method is presented. The method enables the evaluation of all the in-plane normal stress components with similar response to measurement errors, significantly lower than with single-axis measurements. A numerical method is described that takes advantage of, and compactly handles, the additional optical data that are available from the second measurement axis. Experimental tests were conducted on a calibrated specimen to demonstrate the proposed method, and the results supported theoretical expectations.

Residual Stresses Prediction for CO2 Laser Butt-Welding of 304-Stainless Steel

2006 ◽  
Vol 3-4 ◽  
pp. 125-130 ◽  
Author(s):  
Khaled Y. Benyounis ◽  
Abdul Ghani Olabi ◽  
M.S.J. Hashmi
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Residual Stresses ◽  
Laser Power ◽  
Travel Speed ◽  
304 Stainless Steel ◽  
Hole Drilling ◽  
Design Matrix ◽  
Butt Welding ◽  
Input Variables

Residual stresses are an integral part of the total stress acting on any component in service. It is important to determine and/or predict the magnitude, nature and direction of the residual stress to estimate the life of important engineering parts, particularly welded components. This work aims to introduce experimental models to predict residual stresses in the heat-affected zone (HAZ). These models specify the effect of laser welding input parameters on maximum residual stress and its direction. The process input variables considered in this study are laser power (1.03 - 1.368 kW), travel speed (26.48 – 68.52 cm/min) and focal point position (- 1 to 0 mm). Laser butt-welding of 304 stainless steel plates of 3 mm thick were investigated using a 1.5 kW CW CO2 Rofin laser as a welding source. Hole-drilling method was employed to measure the magnitude, and direction of the maximum principal stress in and around the HAZ, using a CEA-06- 062UM-120 strain gauge rosette, which allows measurement of the residual stresses close to the weld bead. The experiment was designed based on Response Surface Methodology (RSM). Fifteen different welding conditions plus 5 repeat tests were carried out based on the design matrix. Maximum principal residual stresses and their directions were calculated for the twenty samples. The stepwise regression method was selected using Design-expert software to fit the experimental responses to a second order polynomial. Sequential F test and other adequacy measures were then used to check the models adequacy. The experimental results indicate that the proposed mathematical models could adequately describe the residual stress within the limits of the factors being studied. Using the models developed, the main and interaction effect of the process input variables on the two responses were determined quantitatively and presented graphically. It is observed that the travel speed and laser power are the main factors affecting the behavior of the residual stress. It is recommended to use the models to find the optimal combination of welding conditions that lead to minimum distortion.

Post Welding Heat Treatment Simulation in Welded Stainless Steel Pipe and Comparison with Experiment

2009 ◽  
Vol 83-86 ◽  
pp. 237-243
Author(s):  
Mohammad Sedighi ◽  
B. Davoodi
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Stainless Steel ◽  
Stress Distribution ◽  
Numerical Models ◽  
Welding Process ◽  
Steel Pipe ◽  
Hole Drilling ◽  
Distribution Data ◽  
Stainless Steel Pipe

Due to the intense concentration of heat in the welding process, residual stresses are produced in the specimen. One of the most effective ways to relief welding stress is Post Welding Heat Treatment (PWHT). In this paper, finite element method is employed to model and analyze PWHT for two pass butt-welded SUS304 stainless steel pipe. In this simulation, firstly, the welding process has been modeled. Then the stress distribution of the specimen has been transferred to a second analysis for stress relaxation modeling. Norton law is used to investigate creep in stress relief process. Experimental tests are also carried out to verify the effectiveness of the proposed numerical models. The hole drilling method is used to measure the stress distribution in the specimen. The residual stress distribution data before and after PWHT are compared to investigate the effect of heat treatment on residual stress. Based on the modeling and experimental results, the tensile and compressive stresses distributions have been reduced. They are in a reasonable agreement with each other and prove the capability of the proposed modeling technique to simulate PWHT.

Simulation and Analysis on the Blind Hole Method Using the Finite Element Method

2013 ◽  
Vol 328 ◽  
pp. 990-994
Author(s):  
Chun Ho Yin ◽  
Chao Ming Hsu ◽  
Ping Shen Su ◽  
Jao Hwa Kuang
Keyword(s):  
Finite Element Method ◽  
Residual Stress ◽  
Finite Element ◽  
Strain Gage ◽  
Hole Drilling ◽  
Drilling Process ◽  
Dimensionless Parameters ◽  
Inconel 690 ◽  
Stress Components ◽  
Element Method

This study investigates the effectiveness of the hole-drilling strain gage method on residual stress estimation. The thermal elastic-plastic model of the commercial Marc finite element method package is used to simulate and build up the hole-drilling process and residual stress distribution. Two Inconel 690 alloy plate welded with GTAW filler I-52 solder are first simulated using the Marc software. The traditional hole-drilling process is then simulated. The simulated residual strain variation data is incorporated into the hole-drilling strain-gage method to derive the possible residual stress components. The effects of drilling depth and drill size on the accuracy of residual stress estimates are also discussed. A comparison of stress components estimated from the traditional hole-drilling strain gage method and simulated from the Marc software is presented. The modified dimensionless parameters are provided by applying the optimum technique. The numerical results indicate that the proposed dimensionless parameters can significantly improve the accuracy of estimated residual stress components.

Measurement of residual stresses in T-plate weldments

2003 ◽  
Vol 38 (4) ◽  
pp. 349-365 ◽  
Author(s):  
R. C Wimpory ◽  
P. S May ◽  
N. P O'Dowd ◽  
G. A Webster ◽  
D J Smith ◽  
...  
Keyword(s):  
Residual Stress ◽  
Neutron Diffraction ◽  
Plastic Zone ◽  
Residual Stresses ◽  
Plate Thickness ◽  
Welding Process ◽  
Plastic Zone Size ◽  
Hole Drilling ◽  
Stress Distributions ◽  
Premature Failure

Tensile welding residual stresses can, in combination with operating stresses, lead to premature failure of components by fatigue and/or fracture. It is therefore important that welding residual stresses are accounted for in design and assessment of engineering components and structures. In this work residual stress distributions, obtained from measurements on a number of ferritic steel T-plate weldments using the neutron diffraction technique and the deep-hole drilling method, are presented. It has been found that the residual stress distributions for three different plate sizes are of similar shape when distances are normalized by plate thickness. It has also been found that the conservatisms in residual stress profiles recommended in current fracture mechanics-based safety assessment procedures can be significant—of yield strength magnitude in certain cases. Based on the data presented here a new, less-conservative transverse residual stress upper bound distribution is proposed for the T-plate weldment geometry. The extent of the plastic zone developed during the welding process has also been estimated by use of Vickers hardness and neutron diffraction measurements. It has been found that the measured plastic zone sizes are considerably smaller than those predicted by existing methods. The implications of the use of the plastic zone size as an indicator of the residual stress distributions are discussed.

Sign in / Sign up

Export Citation Format

Share Document