Low Cycle Fatigue Behavior of Welded Components: A New Approach — Experiments and Numerical Simulation

2012 ◽  
Author(s):  
Eliane Lang ◽  
Jürgen Rudolph ◽  
Thomas Beier ◽  
Michael Vormwald
Keyword(s):  
Fatigue Life ◽  
Thermal Loading ◽  
Weld Seam ◽  
Low Cycle Fatigue ◽  
Fatigue Behavior ◽  
Strain Curve ◽  
Life Assessment ◽  
New Approach ◽  
Elastic Plastic ◽  
Weld Seams

Nuclear power plant components are often subjected to local plastic deformations due to low cycle operational thermal loading conditions. The fatigue behavior of weld seams is of particular interest in this context. Applicable design codes for fatigue life assessment use factors (e.g. Fatigue strength reduction factors – FSRF) within the simplified elastic-plastic or general elastic-plastic analysis in connection with the design fatigue curves for non-welded components. This way, the influence of the weld seam on the fatigue behavior is approximately considered. Emanating from this status quo ideas for a new approach considering the particularities of the fatigue behavior of the weld seam in more detail are developed. The proposed approach is based on material mechanics and constitutes a combination of experimental findings and numerical calculations in order to determine the local strains and the fatigue relevant influence of geometrical and metallurgical notches induced by the weld seam. Experiments on welded specimens provide the fatigue life as well as the stabilized cyclic stress-strain curve as relevant input parameters for the finite element analyses. The proposed model is capable of considering the exact geometry of the weld seam obtained by 3D scanning with very high resolution and the different material strengths due to the weld. The consideration of the principal influences on the fatigue behavior of weld seams paves the way to the application of established damage parameters such as PJ with the future objective to transfer the results also on arbitrary proportional and non-proportional loadings with variable amplitudes.

Transition From Low Cycle to High Cycle in Uniaxial Fatigue

2013 ◽  
Author(s):  
Mohamed E. M. El-Sayed
Keyword(s):  
Fatigue Life ◽  
High Cycle Fatigue ◽  
Low Cycle Fatigue ◽  
Fatigue Behavior ◽  
Uniaxial Stress ◽  
Life Assessment ◽  
Elastic Behavior ◽  
Cycle Fatigue ◽  
Fatigue Life Assessment ◽  
Component Development

Fatigue is the most critical failure mode of many mechanical component. Therefore, fatigue life assessment under fluctuating loads during component development is essential. The most important requirement for any fatigue life assessment is knowledge of the relationships between stresses, strains, and fatigue life for the material under consideration. These relationships, for any given material, are mostly unique and dependent on its fatigue behavior. Since the work of Wöhler in the 1850’s, the uniaxial stress versus cycles to fatigue failure, which is known as the S-N curve, is typically utilized for high-cycle fatigue. In general, high cycle fatigue implies linear elastic behavior and causes failure after more than 104 or 105 cycles. However. the transition from low cycle fatigue to high cycle fatigue, which is unique for each material based on its properties, has not been well examined. In this paper, this transition is studied and a material dependent number of cycles for the transition is derived based on the material properties. Some implications of this derivation, on assessing and approximating the crack initiation fatigue life, are also discussed.

Random impact FEM simulation of irregularly-shaped media for parametric study of vibratory surface enhancement

2021 ◽  
pp. 095440542199012
Author(s):  
Jing Zhang ◽  
Joselito Yam Alcaraz ◽  
Swee-Hock Yeo ◽  
Arun Prasanth Nagalingam ◽  
Abhay Gopinath
Keyword(s):  
Residual Stress ◽  
Fatigue Life ◽  
Parametric Study ◽  
Thermal Loading ◽  
Low Cycle Fatigue ◽  
Fem Simulation ◽  
Surface Finishing ◽  
Aerospace Materials ◽  
Surface Enhancement ◽  
Steel Balls

Aerospace materials experience high levels of mechanical and thermal loading, high/low cycle fatigue, and damage from foreign objects during service, which can lead to premature retirement. Mechanical surface treatments of metallic components, for example, fan blades and blisks, are proven to improve fatigue life, improve wear resistance and avoid stress corrosion by introducing work hardening, compressive residual stresses of sub-surface, and surface finishing. Vibropeening can enhance aerospace materials’ fatigue life involving the kinetic agitation of hardened steel media in a vibratory finishing machine that induces compressive stresses into the component sub-layers while keeping a finished surface. Spherical steel balls are the most widely used shape among steel-based media and have been explored for decades. However, they are not always versatile, which cannot access deep grooves, sharp corners, and intricate profiles. Steel ballcones or satellites, when mixed with round steel balls and other steel media (diagonals, pins, eclipses, cones), works very well in such areas that ball-shaped media are unable to reach. However, a methodology of study the effect of irregularly-shaped media in surface enhancement processes has not been established. This paper proposes a finite element-based model to present a methodology for the parametric study of vibratory surface enhancement with irregularly-shaped media and investigates residual stress profiles within a treated area of an Inconel component. The methodology is discussed in detail, which involves a stochastic simulation of orientation, impact force, and impact location. The contrasting effects of a high aspect ratio, or an edge contact, as opposed to rounded and oblique contacts are demonstrated, with further analysis on the superposition of these effects. Finally, the simulation results are compared with actual residual stress measurements and was found to have a max percent difference of 34% up to 20 [Formula: see text]m below the media surface.

scholarly journals Influence of turning tool wear on the surface integrity and anti-fatigue behavior of Ti1023

2021 ◽  
Vol 13 (4) ◽  
pp. 168781402110112
Author(s):  
Li Xun ◽  
Wang Ziming ◽  
Yang Shenliang ◽  
Guo Zhiyuan ◽  
Zhou Yongxin ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Plastic Deformation ◽  
Titanium Alloy ◽  
Fatigue Life ◽  
Tool Wear ◽  
Surface Integrity ◽  
Low Cycle Fatigue ◽  
Fatigue Behavior ◽  
Machined Surface ◽  
Deformation Layer

Titanium alloy Ti1023 is a typical difficult-to-cut material. Tool wear is easy to occur in machining Ti1023, which has a significant negative effect on surface integrity. Turning is one of the common methods to machine Ti1023 parts and machined surface integrity has a direct influence on the fatigue life of parts. To control surface integrity and improve anti-fatigue behavior of Ti1023 parts, it has an important significance to study the influence of tool wear on the surface integrity and fatigue life of Ti1023 in turning. Therefore, the effect of tool wear on the surface roughness, microhardness, residual stress, and plastic deformation layer of Ti1023 workpieces by turning and low-cycle fatigue tests were studied. Meanwhile, the influence mechanism of surface integrity on anti-fatigue behavior also was analyzed. The experimental results show that the change of surface roughness caused by worn tools has the most influence on anti-fatigue behavior when the tool wear VB is from 0.05 to 0.25 mm. On the other hand, the plastic deformation layer on the machined surface could properly improve the anti-fatigue behavior of specimens that were proved in the experiments. However, the higher surface roughness and significant surface defects on surface machined utilizing the worn tool with VB = 0.30 mm, which leads the anti-fatigue behavior of specimens to decrease sharply. Therefore, to ensure the anti-fatigue behavior of parts, the value of turning tool wear VB must be rigorously controlled under 0.30 mm during finishing machining of titanium alloy Ti1023.

LOW CYCLE FATIGUE BEHAVIOR AND LIFE PREDICTION OF A CAST COBALT-BASED SUPERALLOY

2012 ◽  
Vol 06 ◽  
pp. 251-256
Author(s):  
HO-YOUNG YANG ◽  
JAE-HOON KIM ◽  
KEUN-BONG YOO
Keyword(s):  
Fatigue Life ◽  
Strain Energy ◽  
Life Prediction ◽  
Prediction Models ◽  
Low Cycle Fatigue ◽  
Fatigue Behavior ◽  
Total Strain ◽  
Cycle Fatigue ◽  
Total Strain Range ◽  
Different Temperatures

Co -base superalloys have been applied in the stationary components of gas turbine owing to their excellent high temperature properties. Low cycle fatigue data on ECY-768 reported in a companion paper were used to evaluate fatigue life prediction models. In this study, low cycle fatigue tests are performed as the variables of total strain range and temperatures. The relations between plastic and total strain energy densities and number of cycles to failure are examined in order to predict the low cycle fatigue life of Cobalt-based super alloy at different temperatures. The fatigue lives is evaluated using predicted by Coffin-Manson method and strain energy methods is compared with the measured fatigue lives at different temperatures. The microstructure observing was performed for how affect able to low-cycle fatigue life by increasing the temperature.

Assessment of Fatigue Life for High-Temperature Pipeline Welds Using X-Ray Diffraction Technique

2007 ◽  
Vol 353-358 ◽  
pp. 130-133
Author(s):  
Keun Bong Yoo ◽  
Jae Hoon Kim
Keyword(s):  
High Temperature ◽  
Fatigue Life ◽  
Fatigue Damage ◽  
Power Plants ◽  
Low Cycle Fatigue ◽  
Diffraction Method ◽  
Life Assessment ◽  
Fatigue Properties ◽  
X Ray Diffraction ◽  
X Ray

The objective of this study is to examine the feasibility of the X-ray diffraction method for the fatigue life assessment of high-temperature steel pipes used for main steam pipelines, re-heater pipelines and headers etc. in power plants. In this study, X-ray diffraction tests were performed on the specimens simulated for low cycle fatigue damage, in order to estimate fatigue properties at the various stages of fatigue life. As a result of X-ray diffraction tests, it was confirmed that the full width at the half maximum (FWHM) decreased with an increase in the fatigue life ratio, and that the FWHM and the residual stress due to fatigue damage were algebraically linearly related to the fatigue life ratio. From this relationship, a direct assessment of the remaining fatigue life was feasible.

Modeling, Simulation, and Experimentation of Fatigue Behavior in Amorphous Solids

2018 ◽  
Vol 774 ◽  
pp. 210-216 ◽  
Author(s):  
Thierry Barriere ◽  
Gang Cheng ◽  
Sami Holopainen
Keyword(s):  
Fatigue Life ◽  
Fatigue Damage ◽  
Stress Reduction ◽  
Low Cycle Fatigue ◽  
Fatigue Behavior ◽  
Amorphous Solids ◽  
Cycle Fatigue ◽  
Unified Approach ◽  
Structural Element ◽  
Modeling Simulation

Amorphous solids, such as certain polymers, alloys, and polymer-based composites,are increasingly used materials in engineering components and thus, their fatigue behavioris of utmost importance. The article presents a unified approach suitable for modeling bothisothermal high cycle and low cycle fatigue behavior. The emphasis is placed on the ductilefatigue in which fatigue damage represents the material degeneration during the creation ofmicro-cracks governing majority of the total fatigue life (up to 95%). The model’s capability fortechnologically important polycarbonate (PC) polymer is addressed. The results, in accordancewith experimental observations, favor ductile fatigue behavior, i.e. damage fields remain smallfor most of the fatigue life and do not cause the macroscopic stress reduction. Due to thisproperty, fatigue life of an entire structural element can be evaluated by exploiting singlelocations at which the fatigue damage decisively emerges.

Multiaxial Low Cycle Fatigue Life Prediction at 300 °C Using Equivalent Strain Appoach

2011 ◽  
Vol 361-363 ◽  
pp. 1669-1672
Author(s):  
Wen Xiao Zhang ◽  
Guo Dong Gao ◽  
Guang Yu Mu
Keyword(s):  
Fatigue Life ◽  
Life Prediction ◽  
Low Cycle Fatigue ◽  
Fatigue Behavior ◽  
Strain Range ◽  
Cyclic Fatigue ◽  
Equivalent Strain ◽  
Multiaxial Fatigue ◽  
Fatigue Life Prediction ◽  
Cycle Fatigue

The low cycle fatigue behavior was experimentally studied with the 3-dimension notched LD8 aluminum alloy specimens at 300°C. The 3- dimension stress-strain responses of specimens were calculated by means of the program ADINA. The multiaxial fatigue life prediction was carried out according to von Mises’s equivalent theory. The results from the prediction showed that the equivalent strain range can be served as the valid mechanics for predicting multiaxial high temperature and low cyclic fatigue life.

Thermo-Mechanical Fatigue Life of Coke Drum Skirt Attachment Designs

2016 ◽  
Author(s):  
Gurumurthy Kagita ◽  
Balaji Srinivasan ◽  
Penchala Sai Krishna Pottem ◽  
Gudimella G. S. Achary ◽  
Subramanyam V. R. Sripada
Keyword(s):  
Fatigue Life ◽  
Low Cycle Fatigue ◽  
Effective Strain ◽  
Analysis Model ◽  
Transfer Coefficients ◽  
Elastic Plastic ◽  
Mechanical Fatigue ◽  
Section Viii ◽  
Thermocouple Temperature ◽  
Transient Thermal

Skirt to bottom head attachments of coke drums experience severe thermo-mechanical cyclic stresses, causing failures due to low cycle fatigue. Accordingly, many skirt attachment designs have evolved over a period of time starting with simple conventional weld build up design, improved weld build up design, integral forged attachment design and others. The objective of this paper is to compare thermo-mechanical fatigue life of three different skirt attachment designs using elastic-plastic fatigue assessment methods of ASME Section VIII, Division 2. A transient thermal analysis model is first developed incorporating appropriate boundary conditions. The time-dependent variable heat transfer coefficients at the inner surface of the coke drum, which change with the operation stages and the levels of oil filling and water quenching, are determined based on the field measured thermocouple temperature data on the outer surface of the coke drum. Sequentially coupled elastic-plastic transient thermo-mechanical stress analyses of coke drum skirt attachments are carried out using both Twice Yield and cycle-by-cycle methods. The effective strain ranges and the fatigue life of three different skirt attachment designs are calculated and compared.

Sign in / Sign up

Export Citation Format

Share Document