Computational Fluid Dynamics Modelling for the Prediction of NOx in a Waste Gas Boiler

2016 ◽  
Author(s):  
Adam Blackmore ◽  
Jennifer Woloshyn ◽  
Duane Baker
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Nitrogen Oxides ◽  
Field Measurements ◽  
Industrial Scale ◽  
Nox Emissions ◽  
Cfd Modelling ◽  
Waste Gas ◽  
Computational Fluid Dynamics Cfd ◽  
Dynamics Modelling

Recent results from CFD modelling of a waste gas boiler (WGB) to predict Nitrogen Oxides (NOx) emissions are presented. A verification / validation discussion is highlighted comparing the computational fluid dynamics (CFD) modelling with field measurements of NOx and flame characteristics. Challenges associated with the accurate prediction of NOx emissions are discussed along with the ability of CFD to accurately model emissions from an industrial scale WGB.

Hydrodynamic evaluation of a full-scale facultative pond by computational fluid dynamics (CFD) and field measurements

2014 ◽  
Vol 70 (3) ◽  
pp. 569-575 ◽  
Author(s):  
Ricardo Gomes Passos ◽  
Marcos von Sperling ◽  
Thiago Bressani Ribeiro
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Short Circuit ◽  
Field Measurements ◽  
Tracer Test ◽  
Full Scale ◽  
Cfd Model ◽  
Cfd Modelling ◽  
Hydraulic Behaviour ◽  
Computational Fluid Dynamics Cfd

Knowledge of the hydraulic behaviour is very important in the characterization of a stabilization pond, since pond hydrodynamics plays a fundamental role in treatment efficiency. An advanced hydrodynamics characterization may be achieved by carrying out measurements with tracers, dyes and drogues or using mathematical simulation employing computational fluid dynamics (CFD). The current study involved experimental determinations and mathematical simulations of a full-scale facultative pond in Brazil. A 3D CFD model showed major flow lines, degree of dispersion, dead zones and short circuit regions in the pond. Drogue tracking, wind measurements and dye dispersion were also used in order to obtain information about the actual flow in the pond and as a means of assessing the performance of the CFD model. The drogue, designed and built as part of this research, and which included a geographical positioning system (GPS), presented very satisfactory results. The CFD modelling has proven to be very useful in the evaluation of the hydrodynamic conditions of the facultative pond. A virtual tracer test allowed an estimation of the real mean hydraulic retention time and mixing conditions in the pond. The computational model in CFD corresponded well to what was verified in the field.

Computational Fluid Dynamics modelling of sedimentation on Mars

2020 ◽  
Author(s):  
Nikolaus J. Kuhn ◽  
Federica Trudu
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Gravitational Force ◽  
Settling Velocity ◽  
Cfd Modelling ◽  
Running Water ◽  
Sediment Sorting ◽  
Computational Fluid Dynamics Cfd ◽  
Dynamics Modelling ◽  
Laminar State

<p>Gravity affects sedimentation of particles suspended in water and gases in two ways: directly by the gravitational force that pulls a particle towards the surface and indirectly by the flow conditions of water or gas around the particles. The latter create a drag which is affected by the settling velocity. Consequently, drag coefficients observed on Earth sand-sized particles cannot be used on Mars because they are likely to overestimate the drag generated by the turbulent flow around the particle on Earth may shift into a more laminar state that generates lower drag. The effect of gravity on settling velocity is not linearly related to particle size, which may affect the sorting of the sand grains deposited from running water.  Experiments carried out during parabolic flights at reduced gravity indicate that the potential error in particle settling and sorting is significant, i.e. leading to wrong interpretations of the flow velocities at the time of deposition. This in turn has implications for reconstruction of Martian environmental conditions from rock textures determined from close-up imagery. This study uses computational fluid dynamics (CFD) modelling to independently assess the effect of gravity on sediment settling velocities and sediment sorting. The CFD modelling also offers a wide capability for reconstruction sedimentation on Mars and thus supports the reconstruction of it’s environmental past, as well as the search for traces of life. </p>

Characterisation of Cell Adhesion to Substrate Materials and the Resistance to Enzymatic and Mechanical Cell-Removal

2008 ◽  
Vol 1097 ◽  
Author(s):  
Helen Jane Griffiths ◽  
John G Harvey ◽  
James Dean ◽  
James A Curran ◽  
Athina E Markaki ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Cell Adhesion ◽  
Liquid Flow ◽  
Adhesive Strength ◽  
Cell Detachment ◽  
Shear Forces ◽  
Cfd Modelling ◽  
Computational Fluid Dynamics Cfd

AbstractCell-implant adhesive strength is important for prostheses. In this paper, an investigation is described into the adhesion of bovine chondrocytes to Ti6Al4V-based substrates with different surface roughnesses and compositions. Cells were cultured for 2 or 5 days, to promote adhesion. The ease of cell removal was characterised, using both biochemical (trypsin) and mechanical (accelerated buoyancy and liquid flow) methods. Computational fluid dynamics (CFD) modelling has been used to estimate the shear forces applied to the cells by the liquid flow. A comparison is presented between the ease of cell detachment indicated using these methods, for the three surfaces investigated.

Application of Computational Fluid Dynamics Simulations to the Analysis of Bank Effects in Restricted Waters

2009 ◽  
Vol 62 (3) ◽  
pp. 477-491 ◽  
Author(s):  
D. C. Lo ◽  
Dong-Taur Su ◽  
Jan-Ming Chen
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Cfd Modelling ◽  
Bank Effect ◽  
Force Increase ◽  
Computational Fluid Dynamics Simulations ◽  
Computational Fluid Dynamics Cfd ◽  
Dynamics Simulations ◽  
Yaw Angle ◽  
Vessel Speed

It is well known that vessels operating in the vicinity of a lateral bank experience a significant yaw moment and sway force. This bank effect has a major impact on the manoeuvring properties of the vessel and must therefore be properly understood to ensure the safe passage of the vessel through the restricted waterway. Accordingly, this study performs a series of simulations using commercial FLOW-3D® computational fluid dynamics (CFD) software and the KRISO 3600 TEU container ship model to examine the effects of the vessel speed and distance to bank on the magnitude and time-based variation of the yaw angle and sway force. The results show that for a given vessel speed, the yaw angle and sway force increase as the distance to bank reduces, while for a given distance between the ship and the bank, the yaw angle and sway force increase with an increasing vessel speed. In addition, it is shown that even when a vessel advances at a very low speed, it experiences a significant bank effect when operating in close vicinity to the bank. Overall, the results presented in this study confirm the feasibility of the CFD modelling approach as a means of obtaining detailed insights into the bank effect without the need for time-consuming and expensive ship trials.

Computational fluid dynamics modelling of hydraulics and sedimentation in process reactors during aeration tank settling

2006 ◽  
Vol 53 (12) ◽  
pp. 257-264 ◽  
Author(s):  
M.D. Jensen ◽  
P. Ingildsen ◽  
M.R. Rasmussen ◽  
J. Laursen
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Control Method ◽  
Waste Water Treatment ◽  
Aeration Tank ◽  
Cfd Modelling ◽  
Design Changes ◽  
Dynamics Modelling ◽  
Tank Design ◽  
Tank Settling

Aeration tank settling is a control method allowing settling in the process tank during high hydraulic load. The control method is patented. Aeration tank settling has been applied in several waste water treatment plants using the present design of the process tanks. Some process tank designs have shown to be more effective than others. To improve the design of less effective plants, computational fluid dynamics (CFD) modelling of hydraulics and sedimentation has been applied. This paper discusses the results at one particular plant experiencing problems with partly short-circuiting of the inlet and outlet causing a disruption of the sludge blanket at the outlet and thereby reducing the retention of sludge in the process tank. The model has allowed us to establish a clear picture of the problems arising at the plant during aeration tank settling. Secondly, several process tank design changes have been suggested and tested by means of computational fluid dynamics modelling. The most promising design changes have been found and reported.

CFD Modelling of Multiphase Flows: An Overview

2003 ◽  
Author(s):  
Rajnish K. Calay ◽  
Arne E. Holdo
Keyword(s):  
Fluid Dynamics ◽  
Mass Transfer ◽  
Computational Fluid Dynamics ◽  
Numerical Modeling ◽  
Mathematical Models ◽  
Cfd Modelling ◽  
Two Phase ◽  
Wide Range ◽  
Computational Fluid Dynamics Cfd ◽  
Numerical Modeling Of Flows

The Computational Fluid Dynamics (CFD) is now increasingly being used for modeling industrial flows, i.e. flows which are multiphase and turbulent. Numerical modeling of flows where momentum, heat and mass transfer occurs at the interface presents various difficulties due to the wide range of mechanisms and flow scenarios present. This paper attempts to provide a summary of available mathematical models and techniques for two-phase flows. Some comments are also made on the models available in the commercially available codes.

Sign in / Sign up

Export Citation Format

Share Document