On-Line Performance Monitoring and Diagnostics for Large Combined Cycle Power Plant

2016 ◽  
Author(s):  
B. Chudnovsky ◽  
L. Levin ◽  
A. Talanker ◽  
V. Mankovsky ◽  
A. Kunin
Keyword(s):  
Power Plant ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Performance Monitoring ◽  
Combined Cycle ◽  
Plant Performance ◽  
Combined Cycle Power Plant ◽  
Large Size ◽  
On Line

Diagnostics of large size combined-cycle power plant components (such as: Gas Turbine, HRSG, Steam Turbine and Condenser) plays a significant role in improving power plant performance, availability, reliability and maintenance scheduling. In order to prevent various faults in cycle operation and as a result a reliability reduction, special monitoring and diagnostic techniques is required, for engineering analysis and utility production management. In this sense an on-line supervision system has developed and implemented for 370 MW combined-cycle. The advanced diagnostic methodology is based on a comparison between actual and target conditions. The actual conditions are calculated using data set acquired continuously from the power plant acquisition system. The target conditions are calculated either as a defined actual best operation (Manufacturer heat balances) or by means of a physical model that reproduces boiler and plant performance at off-design. Both sets of data are then compared to find the reason of performance deviation and then used to monitor plant degradation, to support plant maintenance and to assist on-line troubleshooting. The performance calculation module provides a complete Gas Turbine, HRSG and Steam Turbine island heat balance and operating parameters. This paper describes a study where an on-line performance monitoring tool was employed for continuously evaluating power plant performance. The methodology developed and summarized herein has been successfully applied to large size 360–370 MW combined cycles based on GE and Siemens Gas Turbines, showing good capabilities in estimating the degradation of the main equipment during plant lifetime. Consequently, it is a useful tool for power plant operation and maintenance.

Steam Turbine Driving Compressor for Gas-Steam Combined Cycle Power Plant

2009 ◽  
Author(s):  
Wancai Liu ◽  
Hui Zhang
Keyword(s):  
Power Generation ◽  
Power Plant ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Combined Cycle ◽  
Thermodynamic Process ◽  
Combined Cycle Power Plant ◽  
Steam Cycle

Gas turbine is widely applied in power-generation field, especially combined gas-steam cycle. In this paper, the new scheme of steam turbine driving compressor is investigated aiming at the gas-steam combined cycle power plant. Under calculating the thermodynamic process, the new scheme is compared with the scheme of conventional gas-steam combined cycle, pointing its main merits and shortcomings. At the same time, two improved schemes of steam turbine driving compressor are discussed.

Performance Analysis of a Combined Cycle Power Plant Through Exergetic and Environmental Indices

2017 ◽  
Author(s):  
Edgar Vicente Torres González ◽  
Raúl Lugo Leyte ◽  
Martín Salazar Pereyra ◽  
Helen Denise Lugo Méndez ◽  
Miguel Toledo Velázquez ◽  
...  
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Environmental Indices ◽  
Combined Cycle Power Plant ◽  
Combustion Gases ◽  
Combined Cycle Plant ◽  
Exergetic Analysis ◽  
Gas Turbine Power Plant

In this paper is carried out a comparison between a gas turbine power plant and a combined cycle power plant through exergetic and environmental indices in order to determine performance and sustainability aspects of a gas turbine and combined cycle plant. First of all, an exergetic analysis of the gas turbine and the combined is carried out then the exergetic and environmental indices are calculated for the gas turbine (case A) and the combined cycle (case B). The exergetic indices are exergetic efficiency, waste exergy ratio, exergy destruction factor, recoverable exergy ratio, environmental effect factor and exergetic sustainability. Besides, the environmental indices are global warming, smog formation and acid rain indices. In the case A, the two gas turbines generate 278.4 MW; whereas 415.19 MW of electricity power is generated by the combined cycle (case B). The results show that exergetic sustainability index for cases A and B are 0.02888 and 0.1058 respectively. The steam turbine cycle improves the overall efficiency, as well as, the reviewed exergetic indexes. Besides, the environmental indices of the gas turbines (case A) are lower than the combined cycle environmental indices (case B), since the combustion gases are only generated in the combustion chamber.

Short-Term Optimization of a Combined Cycle Power Plant Integrated With an Inlet Air Conditioning Unit

2020 ◽  
Author(s):  
Weimar Mantilla ◽  
José García ◽  
Rafael Guédez ◽  
Alessandro Sorce
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Air Conditioning ◽  
Combined Cycle ◽  
Plant Performance ◽  
Mixed Integer ◽  
Environmental Load ◽  
Turbine Inlet ◽  
The Impact

Abstract Under new scenarios with high shares of variable renewable electricity, combined cycle gas turbines (CCGT) are required to improve their flexibility, in terms of ramping capabilities and part-load efficiency, to help balance the power system. Simultaneously, liberalization of electricity markets and the complexity of its hourly price dynamics are affecting the CCGT profitability, leading the need for optimizing its operation. Among the different possibilities to enhance the power plant performance, an inlet air conditioning unit (ICU) offers the benefit of power augmentation and “minimum environmental load” (MEL) reduction by controlling the gas turbine inlet temperature using cold thermal energy storage and a heat pump. Consequently, an evaluation of a CCGT integrated with this inlet conditioning unit including a day-ahead optimized operation strategy was developed in this study. To establish the hourly dispatch of the power plant and the operation mode of the inlet conditioning unit to either cool down or heat up the gas turbine inlet air, a mixed-integer linear optimization (MILP) was formulated using MATLAB, aiming to maximize the operational profit of the plant within a 24-hours horizon. To assess the impact of the proposed unit operating under this dispatch strategy, historical data of electricity and natural gas prices, as well as meteorological data and CO2 emission allowances price, have been used to perform annual simulations of a reference power plant located in Turin, Italy. Furthermore, different equipment capacities and parameters have been investigated to identify trends of the power plant performance. Lastly, a sensitivity analysis on market conditions to test the control strategy response was also considered. Results indicate that the inlet conditioning unit, together with the dispatch optimization, increases the power plant’s operational profit by achieving a wider operational range, particularly important during peak and off-peak periods. For the specific case study, it is estimated that the net present value of the CCGT integrated with the ICU is 0.5% higher than the power plant without the unit. In terms of technical performance, results show that the unit reduces the minimum environmental load by approximately 1.34% and can increase the net power output by 0.17% annually.

HRSG Duct Firing Revisited

2018 ◽  
Author(s):  
S. Can Gülen
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Fossil Fuel ◽  
Heat Rate ◽  
Combined Cycle ◽  
Efficiency Improvement ◽  
Combined Cycle Power Plant

Duct firing in the heat recovery steam generator (HRSG) of a gas turbine combined cycle power plant is a commonly used method to increase output on hot summer days when gas turbine airflow and power output lapse significantly. The aim is to generate maximum possible power output when it is most needed (and, thus, more profitable) at the expense of power plant heat rate. In this paper, using fundamental thermodynamic arguments and detailed heat and mass balance simulations, it will be shown that, under certain boundary conditions, duct firing in the HRSG can be a facilitator of efficiency improvement as well. When combined with highly-efficient aeroderivative gas turbines with high cycle pressure ratios and concomitantly low exhaust temperatures, duct firing can be utilized for small but efficient combined cycle power plant designs as well as more efficient hot-day power augmentation. This opens the door to efficient and agile fossil fuel-fired power generation opportunities to support variable renewable generation.

Flexible Combined Cycle Gas Turbine Power Plant Utilising Organic Rankine Cycle Technology

2016 ◽  
Author(s):  
Michael Welch ◽  
Nicola Rossetti
Keyword(s):  
Power Generation ◽  
Power Plant ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Combined Cycle ◽  
Exhaust Gas ◽  
Operational Flexibility

Historically gas turbine power plants have become more efficient and reduced the installed cost/MW by developing larger gas turbines and installing them in combined cycle configuration with a steam turbine. These large gas turbines have been designed to maintain high exhaust gas temperatures to maximise the power generation from the steam turbine and achieve the highest overall electrical efficiencies possible. However, in today’s electricity market, with more emphasis on decentralised power generation, especially in emerging nations, and increasing penetration of intermittent renewable power generation, this solution may not be flexible enough to meet operator demands. An alternative solution to using one or two large gas turbines in a large central combined cycle power plant is to design and install multiple smaller decentralised power plant, based on multiple gas turbines with individual outputs below 100MW, to provide the operational flexibility required and enable this smaller power plant to maintain a high efficiency and low emissions profile over a wide load range. This option helps maintain security of power supplies, as well as providing enhanced operational flexibility through the ability to turn turbines on and off as necessary to match the load demand. The smaller gas turbines though tend not to have been optimised for combined cycle operation, and their exhaust gas temperatures may not be sufficiently high, especially under part load conditions, to generate steam at the conditions needed to achieve a high overall electrical efficiency. ORC technology, thanks to the use of specific organic working fluids, permits efficient exploitation of low temperatures exhaust gas streams, as could be the case for smaller gas turbines, especially when working on poor quality fuels. This paper looks at how a decentralised power plant could be designed using Organic Rankine Cycle (ORC) in place of the conventional steam Rankine Cycle to maximise power generation efficiency and flexibility, while still offering a highly competitive installed cost. Combined cycle power generation utilising ORC technology offers a solution that also has environmental benefits in a water-constrained World. The paper also investigates the differences in plant performance for ORC designs utilising direct heating of the ORC working fluid compared to those using an intermediate thermal oil heating loop, and looks at the challenges involved in connecting multiple gas turbines to a single ORC turbo-generator to keep installed costs to a minimum.

Introducing the 1S.W501G Single-Shaft Combined-Cycle Reference Power Plant

2004 ◽  
Author(s):  
Christian Engelbert ◽  
Joseph J. Fadok ◽  
Robert A. Fuller ◽  
Bernd Lueneburg
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Combined Cycle ◽  
Future Market ◽  
Combined Cycle Power Plant ◽  
Highly Efficient ◽  
Fast Start ◽  
Plant Efficiency

Driven by the requirements of the US electric power market, the suppliers of power plants are challenged to reconcile both plant efficiency and operating flexibility. It is also anticipated that the future market will require more power plants with increased power density by means of a single gas turbine based combined-cycle plant. Paramount for plant efficiency is a highly efficient gas turbine and a state-of-the-art bottoming cycle, which are well harmonized. Also, operating and dispatch flexibility requires a bottoming cycle that has fast start, shutdown and cycling capabilities to support daily start and stop cycles. In order to meet these requirements the author’s company is responding with the development of the single-shaft 1S.W501G combined-cycle power plant. This nominal 400MW class plant will be equipped with the highly efficient W501G gas turbine, hydrogen-cooled generator, single side exhausting KN steam turbine and a Benson™ once-through heat recovery steam generator (Benson™-OT HRSG). The single-shaft 1S.W501G design will allow the plant not only to be operated economically during periods of high demand, but also to compete in the traditional “one-hour-forward” trading market that is served today only by simple-cycle gas turbines. By designing the plant with fast-start capability, start-up emissions, fuel and water consumption will be dramatically reduced. This Reference Power Plant (RPP) therefore represents a logical step in the evolution of combined-cycle power plant designs. It combines both the experiences of the well-known 50Hz single-shaft 1S.V94.3A plant with the fast start plant features developed for the 2.W501F multi-shaft RPP. The paper will address results of the single-shaft 1S.W501G development program within the authors’ company.

scholarly journals Thermodynamic analysis of heat recovery steam generator in combined cycle power plant

2007 ◽  
Vol 11 (4) ◽  
pp. 143-156 ◽  
Author(s):  
Kumar Ravi ◽  
Krishna Rama ◽  
Rama Sita
Keyword(s):  
Power Plant ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Steam Generator ◽  
Heat Recovery ◽  
Combined Cycle ◽  
Heat Recovery Steam Generator ◽  
Combined Cycle Power Plant ◽  
Pressure Steam ◽  
Turbine Output

Combined cycle power plants play an important role in the present energy sector. The main challenge in designing a combined cycle power plant is proper utilization of gas turbine exhaust heat in the steam cycle in order to achieve optimum steam turbine output. Most of the combined cycle developers focused on the gas turbine output and neglected the role of the heat recovery steam generator which strongly affects the overall performance of the combined cycle power plant. The present paper is aimed at optimal utilization of the flue gas recovery heat with different heat recovery steam generator configurations of single pressure and dual pressure. The combined cycle efficiency with different heat recovery steam generator configurations have been analyzed parametrically by using first law and second law of thermodynamics. It is observed that in the dual cycle high pressure steam turbine pressure must be high and low pressure steam turbine pressure must be low for better heat recovery from heat recovery steam generator.

Sign in / Sign up

Export Citation Format

Share Document