Experimental and Numerical Models of Wave Reflection and Transmission by an Ice Floe

Author(s):  
Filippo Nelli ◽  
David M. Skene ◽  
Luke G. Bennetts ◽  
Micheal H. Meylan ◽  
Jason P. Monty ◽  
...  

The marginal ice zone (MIZ) is the outer part of the sea-ice covered ocean, where ice can be found in the form of large floating chucks better known as floes. Since it is the area where the most part of the interaction between ice cover and ocean waves takes place, it requires careful modelling. However existing mathematical models, based on the traditional thin-plate theory, underestimate waves attenuation for the most energetic waves, since the energy dissipation occurring during the process is not taken into account. New laboratory experimental and direct numerical models are presented here. In the experimental model a thin plastic plate is tested under the action of incident waves with varying amplitudes and periods. The same experimental set-up was reproduced using a numerical model, which was developed by coupling a High Order Spectral Numerical Wave Tank with the Navier-Stokes solver IHFOAM. Data from the experiments and numerical models confirm that non-linear effects lead to a decrease of wave transmission.

1978 ◽  
Vol 1 (16) ◽  
pp. 44
Author(s):  
R. Bettess ◽  
C.A. Fleming ◽  
J.C. Heinrich ◽  
O.C. Zienkiewicz ◽  
D.I. Austin

We consider a straight coastline exposed to large regular waves, of typical wave length, 100 m amplitude 1.6 m, and period 12 sec. The radiation stress gradients in the extensive (up to 2 km wide) surf zone cause set up and long-shore currents. Despite these currents, the beach is known to be fairly stable. If now a cooling water intake basin is introduced on the coast, it is required to determine first whether the wave induced currents in the vicinity of the basin will affect the circulation of cooling water and second, whether sediment transport will occur, leading to a dredging requirement for the basin. An extensive programme of physical model testing and numerical studies is being undertaken, in order to answer the above questions, and this paper will survey the progress made to date. At the 15th Coastal Engineering Conference a paper on the application of a mathematical model to the prediction of dredging properties inside a cooling water intake basin was 9 presented by Fleming and Hunt, which described the first stage of this work . - In that paper a sediment transport model was combined interactively with numerical models of wave refraction, wave diffraction, long shore currents and circulation currents. The last of these numerical models was used to evaluate the current patterns due to the interruption of the continuity of the longshore currents, together with the cooling water flows in the vicinity of the basin. In this paper we describe the development of more sophisticated numerical models for the first three stages of the process. An understanding of the process of longshore current and set up creation, depends on the concept of radiation stress, introduced by Longuet-Higgins and Stewart,12'13' ' in a series of papers. A number of workers have since used the radiation stress to determine coastline phenomena, and we now describe a few of the relevant papers, without any attempt at a comprehensive survey. Bowen 5'6 considered a straight coastline with parallel contours, and determined near shore circulation patterns, using a stream function formulation of the shallow water equations, for normally incident waves, with a sinusoidal coastwise variation in wave amplitude. He used a finite difference method to solve for the stream function. Longuet-Higgins10'11 criticized Bowen's use of a constant mixing length (horizontal) viscosity, and introduced a viscosity which varied directly with the distance from the shore, in his one dimensional analytical model for obliquely incident waves. He was able to obtain analytically longshore velocity profiles, which he plotted for a range of viscosities.


Author(s):  
Giovanni Tocci Monaco ◽  
Nicholas Fantuzzi ◽  
Francesco Fabbrocino ◽  
Raimondo Luciano

AbstractIn this work, the bending behavior of nanoplates subjected to both sinusoidal and uniform loads in hygrothermal environment is investigated. The present plate theory is based on the classical laminated thin plate theory with strain gradient effect to take into account the nonlocality present in the nanostructures. The equilibrium equations have been carried out by using the principle of virtual works and a system of partial differential equations of the sixth order has been carried out, in contrast to the classical thin plate theory system of the fourth order. The solution has been obtained using a trigonometric expansion (e.g., Navier method) which is applicable to simply supported boundary conditions and limited lamination schemes. The solution is exact for sinusoidal loads; nevertheless, convergence has to be proved for other load types such as the uniform one. Both the effect of the hygrothermal loads and lamination schemes (cross-ply and angle-ply nanoplates) on the bending behavior of thin nanoplates are studied. Results are reported in dimensionless form and validity of the present methodology has been proven, when possible, by comparing the results to the ones from the literature (available only for cross-ply laminates). Novel applications are shown both for cross- and angle-ply laminated which can be considered for further developments in the same topic.


2021 ◽  
Vol 9 (6) ◽  
pp. 600
Author(s):  
Hyun Dong Kim ◽  
Shin-ichi Aoki

When erosion occurs, sand beaches cannot maintain sufficient sand width, foreshore slopes become steeper due to frequent erosion effects, and beaches are trapped in a vicious cycle of vulnerability due to incident waves. Accordingly, beach nourishment can be used as a countermeasure to simultaneously minimize environmental impacts. However, beach nourishment is not a permanent solution and requires periodic renourishment after several years. To address this problem, minimizing the period of renourishment is an economical alternative. In the present study, using the Tuvaluan coast with its cross-sectional gravel nourishment site, four different test cases were selected for the hydraulic model experiment aimed at discovering an effective nourishment strategy to determine effective alternative methods. Numerical simulations were performed to reproduce gravel nourishment; however, none of these models simultaneously simulated the sediment transport of gravel and sand. Thus, an artificial neural network, a deep learning model, was developed using hydraulic model experiments as training datasets to analyze the possibility of simultaneously accomplishing the sediment transport of sand and gravel and supplement the shortcomings of the numerical models.


2021 ◽  
Vol 11 (12) ◽  
pp. 5638
Author(s):  
Selahattin Kocaman ◽  
Stefania Evangelista ◽  
Hasan Guzel ◽  
Kaan Dal ◽  
Ada Yilmaz ◽  
...  

Dam-break flood waves represent a severe threat to people and properties located in downstream regions. Although dam failure has been among the main subjects investigated in academia, little effort has been made toward investigating wave propagation under the influence of tailwater depth. This work presents three-dimensional (3D) numerical simulations of laboratory experiments of dam-breaks with tailwater performed at the Laboratory of Hydraulics of Iskenderun Technical University, Turkey. The dam-break wave was generated by the instantaneous removal of a sluice gate positioned at the center of a transversal wall forming the reservoir. Specifically, in order to understand the influence of tailwater level on wave propagation, three tests were conducted under the conditions of dry and wet downstream bottom with two different tailwater depths, respectively. The present research analyzes the propagation of the positive and negative wave originated by the dam-break, as well as the wave reflection against the channel’s downstream closed boundary. Digital image processing was used to track water surface patterns, and ultrasonic sensors were positioned at five different locations along the channel in order to obtain water stage hydrographs. Laboratory measurements were compared against the numerical results obtained through FLOW-3D commercial software, solving the 3D Reynolds-Averaged Navier–Stokes (RANS) with the k-ε turbulence model for closure, and Shallow Water Equations (SWEs). The comparison achieved a reasonable agreement with both numerical models, although the RANS showed in general, as expected, a better performance.


Water ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 344
Author(s):  
Le Thi Thu Hien ◽  
Nguyen Van Chien

The aim of this paper was to investigate the ability of some 2D and 3D numerical models to simulate flood waves in the presence of an isolated building or building array in an inundated area. Firstly, the proposed 2D numerical model was based on the finite-volume method (FVM) to solve 2D shallow-water equations (2D-SWEs) on structured mesh. The flux-difference splitting method (FDS) was utilized to obtain an exact mass balance while the Roe scheme was invoked to approximate Riemann problems. Secondly, the 3D commercially available CFD software package was selected, which contained a Flow 3D model with two turbulent models: Reynolds-averaged Navier-Stokes (RANs) with a renormalized group (RNG) and a large-eddy simulation (LES). The numerical results of an impact force on an obstruction due to a dam-break flow showed that a 3D solution was much better than a 2D one. By comparing the 3D numerical force results of an impact force acting on building arrays with the existence experimental data, the influence of velocity-induced force on a dynamic force was quantified by a function of the Froude number and the water depth of the incident wave. Furthermore, we investigated the effect of the initial water stage and dam-break width on the 3D-computed results of the peak value of force intensity.


2013 ◽  
Vol 569-570 ◽  
pp. 595-602 ◽  
Author(s):  
William Finnegan ◽  
Jamie Goggins

A vital aspect of ensuring the cost effectiveness of wave energy converters (WECs) is being able to monitor their performance remotely through structural health monitoring, as these devices are deployed in very harsh environments in terms of both accessibility and potential damage to the devices. The WECs are monitored through the use of measuring equipment, which is strategically placed on the device. This measured data is then compared to the output from a numerical model of the WEC under the same ocean wave conditions. Any deviations would suggest that there are problems or issues with the WEC. The development of accurate and effective numerical models is necessary to minimise the number of times the visual, or physical, inspection of a deployed WEC is required. In this paper, a numerical wave tank model is, first, validated by comparing the waves generated to those generated experimentally using the wave flume located at the National University of Ireland, Galway. This model is then extended so it is suitable for generating real ocean waves. A wave record observed at the Atlantic marine energy test site has been replicated in the model to a high level of accuracy. A rectangular floating prism is then introduced into the model in order to explore wave-structure interaction. The dynamic response of the structure is compared to a simple analytical solution and found to be in good agreement.


Author(s):  
Stefan Schmid ◽  
Rudi Kulenovic ◽  
Eckart Laurien

For the validation of empirical models to calculate leakage flow rates in through-wall cracks of piping, reliable experimental data are essential. In this context, the Leakage Flow (LF) test rig was built up at the IKE for measurements of leakage flow rates with reduced pressure (maximum 1 MPA) and temperature (maximum 170 °C) compared to real plant conditions. The design of the test rig enables experimental investigations of through-wall cracks with different geometries and orientations by means of circular blank sheets with integrated cracks which are installed in the tubular test section of the test rig. In the paper, the experimental LF set-up and used measurement techniques are explained in detail. Furthermore, first leakage flow measurement results for one through-wall crack geometry and different imposed fluid pressures at ambient temperature conditions are presented and discussed. As an additional aspect the experimental data are used for the determination of the flow resistance of the investigated leak channel. Finally, the experimental results are compared with numerical results of WinLeck calculations to prove specifically in WinLeck implemented numerical models.


2021 ◽  
Author(s):  
Murat Zeybek ◽  
Lei Jiang ◽  
Hadrien Dumont

Abstract The radius of investigation (ROI) of pressure transient analyses has been traditionally assessed using analytical formulations with basic reservoir parameters for homogenous systems. Numerous studies aimed to improve ROI formulations to incorporate all reservoir and testing parameters such as gauge resolution and rate for more accurate ROI assessments. However, new generation wireline formation testers aim to improve deep transient tests with significant developments in gauge resolution and increasing rate. Challenges still remain in heterogeneous formations such as shaly sands and carbonate reservoirs. In this study, detailed conceptual high-resolution numerical models are set up, including comprehensive reservoir and measurement parameters, to investigate more realistic ROI assessments in layered heterogeneous systems without and with hydraulic communication. Several conceptual examples are presented in layered systems with permeability contrasts. In addition, deviation from infinite-acting radial flow (IAFR) and pressure propagation in highly heterogeneous layered systems are investigated to detect the presence of geological features, including closed boundary systems and the presence of a fault in the proximity of wellbore.


2012 ◽  
Vol 524-527 ◽  
pp. 699-704
Author(s):  
Xiao Gang Xia ◽  
Yun Feng Yang

Based on the overburden three caving feature, the deformation of mining rock process was devided and the criterion of gradual transformation of each stages deformation were given. Then , combined the thin-plate theory, the differential models were derived for rock deformation in level and similar to level bured condition. The boundary condition of each models and exchange condition between different models were put forward and the gradual mechanics model was set up.The subsidence model before roof collapse was solved by Navier double trigonometric series and the deflection surface expression of rock deformation was put forword. At last, the reliability and practicality of the models was verified by engineering examples.


Sign in / Sign up

Export Citation Format

Share Document