A Numerical Study on Correlation Between the Bow Design Parameters and Added Resistance Using the Design of Experiments

2016 ◽  
Author(s):  
Gwan Hoon Kim ◽  
Hyun Joon Shin ◽  
Jeonghwa Seo ◽  
Shin Hyung Rhee
Keyword(s):  
Design Of Experiments ◽  
Numerical Simulations ◽  
Numerical Study ◽  
Design Parameters ◽  
Added Resistance ◽  
Hull Form ◽  
Entrance Angle ◽  
Wave Condition ◽  
Added Resistance In Waves ◽  
Bulbous Bow

In this study, numerical computation was carried out for evaluating the effects of the design parameter variations on the added resistance of Aframax tanker in head seas. The design of experiments (DOE) was used to efficiently conduct the numerical simulations with the hull form variations and save computational resources. A computational fluid dynamics (CFD) code based on the continuity and Reynolds averaged Navier-Stokes (RANS) equation was used for the numerical simulation. The simulation was performed in a short wave condition where the wave length was half of the ship length, which is expected to be most frequent in the vessel operation. Five design parameters of fore-body hull form were selected for the variations: design waterline length (DWL), bulbous bow height (BBH), bulbous bow volume (BBV), bow flare angle (BFA) and bow entrance angle (BEA). Each parameter had two levels in the variations, thus total 32 cases were designed initially. The results of the numerical simulations were analyzed statistically to determine the main effects and correlations in the five design parameters variations. Among them, the most significant parameter that influences on the added resistance in waves was DWL, followed by BBV and BEA. The other parameters had little effects on the added resistance in waves. By the computations, it was revealed that Extending DWL and decreasing BEA promoted the reflection of waves more toward the side than forward. In addition, there existed two-way interactions for the following two-factor combinations: DWL-BFA, DWL-BEA, DWL-BBV, BBH-BBV.

scholarly journals Application of the Design of Experiments and Computational Fluid Dynamics to Bow Design Improvement

2019 ◽  
Vol 7 (7) ◽  
pp. 226 ◽  
Author(s):  
Woochan Seok ◽  
Gwan Hoon Kim ◽  
Jeonghwa Seo ◽  
Shin Hyung Rhee
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Design Of Experiments ◽  
Wavelength Region ◽  
Regression Equation ◽  
Design Parameters ◽  
Added Resistance ◽  
Short Wavelength Region ◽  
Hull Form ◽  
Design Elements

Techniques of the design of experiments (DOE) and computational fluid dynamics (CFD) were applied for improving the bow shape of a tanker hull. Through this, a hull that could reduce the added resistance in waves was derived. The key design elements of the bow shape were selected as parameters for design optimization and added resistance in the short-wavelength region was interpreted through CFD considering the operational condition of the full scale ship. For design parameter changes, the number of analyses was minimized by applying DOE. The regression equation for calculating added resistance was derived using bow-shape design parameters by applying the response surface method and regression analysis to obtain the optimal hull with minimal added resistance was derived. The methodology was applied to an Aframax tanker hull form, and the derived added resistance regression equation and the added resistance value obtained through CFD analysis showed a difference of approximately 1%. The model test results of the improved hull form showed that the added resistance was reduced by 52% in comparison to that obtained for the original hull form.

Hydrodynamic Optimization of a Wedge Hull

2015 ◽  
Author(s):  
Lijue Wang ◽  
Fuxin Huang ◽  
Chi Yang ◽  
Raju Datla
Keyword(s):  
Hydrodynamic Performance ◽  
Surface Mesh ◽  
Nurbs Surface ◽  
Bottom Edge ◽  
Hull Form ◽  
Entrance Angle ◽  
Total Drag ◽  
Rounded Corner ◽  
Bulbous Bow ◽  
Hydrodynamic Optimization

A novel wedge-shaped hull form is optimized for reduced drag using a further developed practical hydrodynamic optimization tool. The hull features a sharp entrance angle, rectilinear sides, sharp bottom edges, a triangular waterplane and a linear aftward taper from a deep bow to a shallow transom. The optimization involves two modifications of the hull form, one is to smooth out the sharp bottom edge with a rounded corner and the other is to generate a bulbous bow. In order to perform the hydrodynamic optimization of the hull, a Non-Uniform Rational BSpline (NURBS)-based hull surface modification tool, a NURBS surface mesh generator, a surrogate model and an evolutionary optimization solver are developed and integrated into the practical hydrodynamic optimization tool. The hydrodynamic performances, i.e., the total drag and the flow field near the obtained hull bodies are assessed and compared with the original wedge hull using numerical simulations. Results showed that rounding the sharp edge of the wedge hull can reduce the total drag by alleviating the flow separations around the hull body. The wedge hull with rounded bottom edge and optimized bulbous bow can achieve larger drag reduction and the flow separations are almost eliminated. The total drag of the optimal hull is compared with an earlier-optimized wedge hull that has a different type of bulbous bow, whose hydrodynamic performance has been validated by model tests.

Sailing Yacht Performance in Calm Water and in Waves

1993 ◽  
Author(s):  
J. Gerritsma ◽  
J. A. Keuning ◽  
A. Versluis
Keyword(s):  
Model Experiment ◽  
Irregular Waves ◽  
Current Interest ◽  
Added Resistance ◽  
Hull Form ◽  
Wide Range ◽  
Calm Water ◽  
Added Resistance In Waves ◽  
Sailing Yacht ◽  
Calculated Analysis

The Delft systematic Yatch Hull Series has been extended to a total of 39 hull form variations, covering a wide range of length displacement ratios and other form of parameters. The total set of model experiment results, upright and heeled resistance as well as sideforce and stability, had been analysed and polynomial expressions to approximate these quantities are presented. In view of the current interest in the performance of sailing yachts in waves, the added resistance in irregular waves of 8 widely different hull variations has been calculated. Analysis of the results shows that the added resistance in waves strongly depends on the product of displacement-length ratio and the gyradius of the pitching motion.

scholarly journals Added Resistance in Waves and Amplitude Function Expressing a Ship Hull Form

2008 ◽  
Vol 8 (0) ◽  
pp. 163-169 ◽  
Author(s):  
Shigeru Naito ◽  
Mariko Kuroda ◽  
Hisahumi Yoshida ◽  
Takehiro Ikeda
Keyword(s):  
Ship Hull ◽  
Added Resistance ◽  
Amplitude Function ◽  
Hull Form ◽  
Added Resistance In Waves

Hydrodynamic Performance and Appendage Considerations of Wave-Piercing Planing Craft Overlapping Waves and Porpoising

2019 ◽  
Author(s):  
Sang-Won Kim ◽  
Sang-Eui Lee ◽  
Gyoung-Woo Lee ◽  
Kwang-Cheol Seo ◽  
Nobuyuki Oshima
Keyword(s):  
Numerical Simulation ◽  
Pressure Distribution ◽  
High Speed ◽  
Numerical Study ◽  
Hydrodynamic Performance ◽  
Moving Mesh ◽  
Navier Stokes ◽  
Hull Form ◽  
Wave Condition ◽  
Planing Craft

Abstract This work addresses the numerical study of wave-piercing planing hull and related hydrodynamic performance as the appendages. From the half century ago, the interest in high-speed planing crafts has been advanced toward maintaining performance stably. The main reasons to make it hard are instability motion occurring from porpoising and wave condition. Porpoising is mainly due to overlap the heaving and pitching motion with certain period, which is caused by instable pressure distribution and changing longitudinal location of center of gravity. In addition, in wave condition, encountering wave disturbs going into planing mode. This paper presents numerical results of wave-piercing planing hull in porpoising and wave condition. Numerical simulation is conducted via Reynolds Averaged Navier-stokes (RANS) with moving mesh techniques (overset grid), performed at different wave condition. The results for the behaviors of wave-piercing hull form are practically presented and investigated in this study. The understanding of these phenomena is important for design of appendages of wave-piercing hull-form.

Experimental investigation on the added resistance of modified KVLCC2 hull forms with different bow shapes

2016 ◽  
Vol 231 (2) ◽  
pp. 395-410
Author(s):  
Jaehoon Lee ◽  
Dong-Min Park ◽  
Yonghwan Kim
Keyword(s):  
Model Tests ◽  
Green Water ◽  
Added Resistance ◽  
Hull Form ◽  
Motion Responses ◽  
Wide Range ◽  
Added Resistance In Waves ◽  
Design Speed ◽  
Hull Forms ◽  
Motion Amplitude

The effect of different bow shapes on the added resistance in waves was observed through a series of model tests. To this end, three different hull forms of KRISO Very Large Crude Carrier 2 were considered: an original hull form and two modified hulls with different bow shapes, called ax-bow and leadge-bow. The model tests were conducted for a wide range of wavelengths with two wave amplitudes in a regular head-sea condition at the design speed. Each test condition was imposed at least twice in order to check the repeatability of measurement, considering the uncertainties in model test and the nonlinear nature of the added resistance. This article introduces a preliminary study on the effects of surge motion, amplitude of incident wave, and green-water allowance around bow region. This article briefly includes the uncertainty analysis of recent study regarding the performance of the original hull. Based on the results of the experimental study for three different bow shapes, the parameters which influence the added resistance and motion responses are discussed.

A Novel Measure to Reduce Ship Resistance in Waves

2017 ◽  
Author(s):  
Bingjie Guo ◽  
Bjørn-Johan Vartdal ◽  
Sverre Steen
Keyword(s):  
Cfd Simulation ◽  
Low Cost ◽  
Ship Motions ◽  
The Novel ◽  
Added Resistance ◽  
Wave Condition ◽  
Oblique Waves ◽  
Ship Resistance ◽  
Added Resistance In Waves ◽  
3D Effect

Ships travel in waves most of the time. The horsepower increase or speed loss in waves can become large in adverse sea. Speed loss needs to be compensated for by increasing the power. Moreover, the associated speed-loss can possibly not be compensated due to the limit of installed power. This will cause delays, and may even lead to safety concerns in maneuvering. Thus, there is a need for minimizing added resistance due to both economical and safety reasons. Ships with better performance in waves even with reduced power are desired. Latest researches on advanced ship optimization are taking added resistance into account. Ship bow optimization has been the main measure to reduce added resistance in waves. Based on analyzing the working principles and potential benefit of the different kinds of novel ship bows, a novel measure is proposed to reduce the ship resistance in waves is proposed. A novel measure to reduce the ship resistance in waves of existing ships by installing a simple structure at the ship bow. The structure is designed to sharpen the ship bow and therefore reduce added resistance due to wave reflection. Thus, it is suitable for the large tankers and bulk carriers, which have blunt bows. The volume above free surface was expected to reduce ship motions and the added resistance due to ship motions consequently. This measure does not change the original ship design. It can be retrofitted on existing ships fairly easily at low cost. In order to verify the benefit due to the retrofitted structure, CFD simulations are performed in both head and oblique waves, which can take 3D effect into account. Four different retrofitted structures are designed and the numerical simulations are performed with the same numerical and mesh settings in each wave condition. The CFD simulation results confirm that the novel measure can reduce ship added resistance efficiently and it also has benefits in oblique waves.

Using Ansys for Design and Numerical Study of a Specific Fixed Wing UAV

2018 ◽  
Vol 55 (4) ◽  
pp. 652-657 ◽  
Author(s):  
Gabriel Murariu ◽  
Razvan Adrian Mahu ◽  
Adrian Gabriel Murariu ◽  
Mihai Daniel Dragu ◽  
Lucian P. Georgescu ◽  
...  
Keyword(s):  
Numerical Simulations ◽  
Unmanned Aerial Vehicle ◽  
Numerical Study ◽  
Flight Time ◽  
Cluster System ◽  
Numerical Results ◽  
Operational Performance ◽  
Gliding Flight ◽  
Aerial Vehicle ◽  
Constant Altitude

This article presents the design of a specific unmanned aerial vehicle UAV prototype own building. Our UAV is a flying wing type and is able to take off with a little boost. This system happily combines some major advantages taken from planes namely the ability to fly horizontal, at a constant altitude and of course, the great advantage of a long flight-time. The aerodynamic models presented in this paper are optimized to improve the operational performance of this aerial vehicle, especially in terms of stability and the possibility of a long gliding flight-time. Both aspects are very important for the increasing of the goals� efficiency and for the getting work jobs. The presented simulations were obtained using ANSYS 13 installed on our university� cluster system. In a next step the numerical results will be compared with those during experimental flights. This paper presents the main results obtained from numerical simulations and the obtained magnitudes of the main flight coefficients.

scholarly journals AC Current Ripple in Three-Phase Four-Leg PWM Converters with Neutral Line Inductor

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1430
Author(s):  
Aleksandr Viatkin ◽  
Riccardo Mandrioli ◽  
Manel Hammami ◽  
Mattia Ricco ◽  
Gabriele Grandi
Keyword(s):  
Numerical Simulations ◽  
Pulse Width Modulation ◽  
Neutral Line ◽  
Experimental Tests ◽  
Performance Comparison ◽  
Design Parameters ◽  
Switching Frequency ◽  
Three Phase ◽  
Ac Current ◽  
Current Ripple

This paper presents a comprehensive study of peak-to-peak and root-mean-square (RMS) values of AC current ripples with balanced and unbalanced fundamental currents in a generic case of three-phase four-leg converters with uncoupled AC interface inductors present in all three phases and in neutral. The AC current ripple characteristics were determined for both phase and neutral currents, considering the sinusoidal pulse-width modulation (SPWM) method. The derived expressions are simple, effective, and ready for accurate AC current ripple calculations in three- or four-leg converters. This is particularly handy in the converter design process, since there is no need for heavy numerical simulations to determine an optimal set of design parameters, such as switching frequency and line inductances, based on the grid code or load restrictions in terms of AC current ripple. Particular attention has been paid to the performance comparison between the conventional three-phase three-leg converter and its four-leg counterpart, with distinct line inductance values in the neutral wire. In addition to that, a design example was performed to demonstrate the power of the derived equations. Numerical simulations and extensive experimental tests were thoroughly verified the analytical developments.

Sign in / Sign up

Export Citation Format

Share Document