Numerical Prediction of the Propulsion Characteristics of Ships in Waves

2016 ◽  
Author(s):  
Sebastian Sigmund ◽  
Ould el Moctar
Keyword(s):  
Equations Of Motion ◽  
Open Water ◽  
Computational Effort ◽  
The Self ◽  
Experimental Results ◽  
Characteristic Change ◽  
Flow Solver ◽  
Head Waves ◽  
Calm Water ◽  
Regular Head Waves

The influence of regular head waves on the propulsion characteristics of a twin screw cruise ship is investigated using RANS based flow-solver. Propeller open water characteristics are determined at first by computing the propeller forces in homogeneous inflow. Then, computations of the towed model without propeller and of the self-propelled model in calm water are performed to obtain the propulsion characteristics in calm water. Afterwards, the total resistance as well as the forces of the self-propelled model in regular head waves are computed. All computations are performed using a RANS based flow-solver coupled with the six-degrees-of-freedom equations of motion. The sliding interface method is used to allow the rotation of the geometrically modelled propeller, when needed. Computations are performed using the same numerical grids to keep errors originating on different spatial and temporal discretization as small as possible. Grid studies are performed to evaluate discretization errors of each mesh region, namely the hull region and the rotating propeller region, separately. The numerical results are compared with experimental results obtained from physical tests. It is shown, that RANS is capable of investigating the propulsion behavior of a ship in regular head waves, but to the cost of high computational effort. Fair agreement between numerical and experimental results is obtained. All results show that the propulsion characteristic change in waves. It is also found, that this is mainly caused by the change of the propeller efficiency due to a different propulsion point as a consequence of the added resistance in waves.

Unsteady Numerical Simulation of the Behavior of a Ship Moving in Head Sea

2019 ◽  
Author(s):  
Adrian Lungu
Keyword(s):  
Free Surface Flow ◽  
Surface Flow ◽  
Incoming Wave ◽  
Grid Convergence ◽  
Head Waves ◽  
Calm Water ◽  
Unsteady Numerical Simulation ◽  
Resistance Coefficients ◽  
Regular Head Waves ◽  
Numerical Approaches

Abstract The paper follows a previous work of the author that dealt with ship resistance and self-propulsion numerical investigations, proposing a series of numerical simulations performed to assess the seakeeping performances of the KCS model which moves in regular head waves. Various simulations of the free-surface flow around the hull equipped with rudder moving either in calm water or in heading waves are proposed. For the calm water case, in which a series of six Fr numbers is considered, verification and validation based on the grid convergence tests are performed. Then, a series of five different simulations for various incoming wave characteristics are presented and discussed in every detail. Comparisons with the experimental data [1], [2] are provided aimed at validating the numerical approaches in terms of the total resistance coefficients as well as the heave and pitch motions characteristics. Several remarks will conclude the findings of the present work.

scholarly journals Full-Scale CFD Analysis of Double-M Craft Seakeeping Performance in Regular Head Waves

2021 ◽  
Vol 9 (5) ◽  
pp. 504
Author(s):  
Deniz Ozturk ◽  
Cihad Delen ◽  
Simone Mancini ◽  
Mehmet Ozan Serifoglu ◽  
Turgay Hizarci
Keyword(s):  
Full Scale ◽  
Stokes Wave ◽  
Added Resistance ◽  
Motion Responses ◽  
Seakeeping Performance ◽  
Head Waves ◽  
Calm Water ◽  
Maximum Improvement ◽  
Fifth Order ◽  
Regular Head Waves

This study presents the full-scale resistance and seakeeping performance of an awarded Double-M craft designed as a 15 m next-generation Emergency Response and Rescue Vessel (ERRV). For this purpose, the Double-M craft is designed by comprising the benchmark Delft 372 catamaran with an additional center and two side hulls. First, the resistance and seakeeping analyses of Delft 372 catamaran are simulated on the model scale to verify and compare the numerical setup for Fr = 0.7. Second, the seakeeping performance of the full-scale Double-M craft is examined at Fr = 0.7 in regular head waves (λ/L = 1 to 2.5) for added resistance and 2-DOF motion responses. The turbulent flow is simulated by the unsteady RANS method with the Realizable Two-Layer k-ε scheme. The calm water is represented by the flat VOF (Volume of Fluid) wave, while the incident long waves are represented by the fifth-order Stokes wave. The residual resistance of the Double-M craft is improved by 2.45% compared to that of the Delft 372 catamaran. In the case of maximum improvement (at λ/L = 1.50), the relative added resistance of the Double-M craft is 10.34% lower than the Delft 372 catamaran; moreover, the heave and pitch motion responses were 72.5% and 35.5% less, respectively.

scholarly journals NUMERICAL INVESTIGATION OF INTERCEPTOR EFFECT ON SEA KEEPING BEHAVIOUR OF PLANING HULL ADVANCING IN REGULAR HEAD WAVES

Brodogradnja ◽  
2021 ◽  
Vol 72 (2) ◽  
pp. 73-92
Author(s):  
Jangam Suneela ◽  
◽  
Prasanta Sahoo ◽  
Keyword(s):  
Numerical Data ◽  
Navier Stokes ◽  
Hydrodynamic Characteristics ◽  
Head Waves ◽  
Calm Water ◽  
Vessel Response ◽  
Planing Vessel ◽  
Motion Characteristics ◽  
The Impact ◽  
Regular Head Waves

In this paper an attempt has been made to assess the capability of numerical algorithm based on Reynolds Averaged Navier Stokes (RANS) for predicting the motion characteristics of the planing hull in calm water and regular waves. The focus of the present study is the impact of interceptors on the sea keeping quality of a planing vessel investigated through the application of numerical methods. The wave properties such as wavelength and wave height are taken into consideration to investigate the effect of wave steepness on vessel response. It is found that numerical data can efficiently simulate the motion attitude and the hydrodynamic characteristics of planing craft in regular head waves. The planing hull with and without interceptor fitted at the transom is simulated in numerical wave tank. The results show reduction in heave and pitch motions which gave favorable sea keeping behavior for the hull fitted with interceptor. The numerical solution is useful for the preliminary prediction of navigation safety during sailing.

Lateral Tire Forces on Wet Roads

1977 ◽  
Vol 5 (2) ◽  
pp. 75-82 ◽  
Author(s):  
A. Schallamach
Keyword(s):  
Normal Load ◽  
The Self ◽  
Experimental Results ◽  
Slip Angle ◽  
Tire Model ◽  
Side Force ◽  
Tire Forces

Abstract Expressions are derived for side force and self-aligning torque of a simple tire model on wet roads with velocity-dependent friction. The results agree qualitatively with experimental results at moderate speeds. In particular, the theory correctly predicts that the self-aligning torque can become negative under easily realizable circumstances. The slip angle at which the torque reverses sign should increase with the normal load.

Analysis of Linear Nonconservative Vibrations

1995 ◽  
Vol 62 (3) ◽  
pp. 685-691 ◽  
Author(s):  
F. Ma ◽  
T. K. Caughey
Keyword(s):  
Modal Analysis ◽  
Equations Of Motion ◽  
Substantial Reduction ◽  
Computational Effort ◽  
Equivalence Transformations ◽  
State Space Approach ◽  
Nonconservative System ◽  
First Order ◽  
Physical Insight ◽  
Space Approach

The coefficients of a linear nonconservative system are arbitrary matrices lacking the usual properties of symmetry and definiteness. Classical modal analysis is extended in this paper so as to apply to systems with nonsymmetric coefficients. The extension utilizes equivalence transformations and does not require conversion of the equations of motion to first-order forms. Compared with the state-space approach, the generalized modal analysis can offer substantial reduction in computational effort and ample physical insight.

Optimization of RANS Solver Simulation Setup for Propeller Open Water Performance Prediction

2015 ◽  
Author(s):  
Mohammed Islam ◽  
Fatima Jahra ◽  
Michael Doucet
Keyword(s):  
Domain Size ◽  
Open Water ◽  
Fractional Factorial ◽  
Navier Stokes ◽  
Calm Water ◽  
Simulation Results ◽  
Open Water Performance ◽  
Thrust And Torque ◽  
Simulation Time ◽  
Fixed Pitch

Mesh and domain optimization strategies for a RANS solver to accurately estimate the open water propulsive characteristics of fixed pitch propellers are proposed based on examining the effect of different mesh and computation domain parameters. The optimized mesh and domain size parameters were selected using Design of Experiments (DoE) methods enabling simulations to be carried out in a limited memory environment, and in a timely manner; without compromising the accuracy of results. A Reynolds-Averaged Navier Stokes solver is used to predict the propulsive performance of a fixed pitch propeller. The predicted thrust and torque for the propeller were compared to the corresponding measurements. A total of six meshing parameters were selected that could affect the computational results of propeller open water performance. A two-level fractional factorial design was used to screen out parameters that do not significantly contribute to explaining the dependent parameters: namely simulation time, propeller thrust and propeller torque. A total of 32 simulations were carried out only to find out that the selected six meshing parameters were significant in defining the response parameters. Optimum values of each of the input parameters were obtained for the DOE technique and additional simulations were run with those parameters. The simulation results were validated using open water experimental results of the same propeller. It was found that with the optimized meshing arrangement, the propeller opens simulation time was reduced by at least a factor of 6 as compared to the generally popular meshing arrangement. Also, the accuracy of propulsive characteristics was improved by up to 50% as compared to published simulation results. The methodologies presented in this paper can be similarly applied to other simulations such as calm water ship resistance, ship propulsion to systematically derive the optimized meshing arrangement for simulations with minimal simulation time and maximum accuracy. This investigation was carried out using STAR-CCM+, a commercial CFD package; however the findings can be applied to any RANS solver.

Sign in / Sign up

Export Citation Format

Share Document