Fatigue of Combined Drag and Inertial Forces

2014 ◽  
Author(s):  
Wenbo Huang
Keyword(s):  
Numerical Analysis ◽  
Fatigue Damage ◽  
High Frequency ◽  
Low Frequency ◽  
Inertial Force ◽  
Frequency Domain Method ◽  
Inertial Forces ◽  
Combined Load ◽  
Drag Forces ◽  
Load Combination

Based on the rain-flow counting technique, a frequency domain method is developed for calculating the fatigue damage caused by the combined drag and inertial loads. Firstly, by observation of the combined signal simulated, the combined load can be considered as the oscillation of the high frequency inertial force around the low frequency drag force with the random amplitudes, which makes it possible to identify the rain-flow large and small cycles. The cyclic range of rain-flow small cycles are determined by considering the reduced effect of the low frequency drag forces on the cyclic range of high frequency inertial forces. The cyclic ranges of rain-flow large cycles are determined by means of Turkstra’s rule of load combination. The numerical analysis show that the damages estimated by the developed method are very close to the rain-flow damages.

Analytical Solutions of Bimodal Gaussian Processes’ Fatigue Damages

2017 ◽  
Author(s):  
Wenbo Huang
Keyword(s):  
Analytical Solutions ◽  
Gaussian Processes ◽  
High Frequency ◽  
Numerical Solutions ◽  
Low Frequency ◽  
Frequency Domain Method ◽  
Load Combination ◽  
Analytical Formulas ◽  
Reduction Effect ◽  
Damage Estimates

Based on the rain-flow counting technique, a frequency domain method is developed for calculating the fatigue damages caused by the bimodal Gaussian loads. Firstly, by considering the reduction effect of low frequency loads on high frequency ones, the amplitudes of the small rain-flow cycles are obtained. Secondly, the amplitudes of the large rain-flow cycles are determined by means of Turkstra’s rule of load combination. Moreover, based on the numerical solutions developed, the two analytical formulas for the damage estimates of small and large cycles are developed. Both numerical and analytical solutions are benchmarked against the rain-flow damage estimates and compared with the existing ones. The numerical analyses show that the damages estimated by the new method are close to the rain-flow damages.

scholarly journals Drag forces on a bed particle in open-channel flow: effects of pressure spatial fluctuations and very-large-scale motions

2019 ◽  
Vol 863 ◽  
pp. 494-512 ◽  
Author(s):  
S. M. Cameron ◽  
V. I. Nikora ◽  
I. Marusic
Keyword(s):  
Channel Flow ◽  
Drag Force ◽  
High Frequency ◽  
Large Scale ◽  
Open Channel ◽  
Low Frequency ◽  
Open Channel Flow ◽  
Stereoscopic Particle Image Velocimetry ◽  
Force Fluctuations ◽  
Drag Forces

The fluctuating drag forces acting on spherical roughness elements comprising the bed of an open-channel flow have been recorded along with synchronous measurements of the surrounding velocity field using stereoscopic particle image velocimetry. The protrusion of the target particle, equipped with a force sensor, was systematically varied between zero and one-half diameter relative to the hexagonally packed adjacent spheres. Premultiplied spectra of drag force fluctuations were found to have bimodal shapes with a low-frequency (${\approx}0.5~\text{Hz}$) peak corresponding to the presence of very-large-scale motions (VLSMs) in the turbulent flow. The high-frequency ($\gtrapprox 4~\text{Hz}$) region of the drag force spectra cannot be explained by velocity time series extracted from points around the particle, but instead appears to be dominated by the action of pressure gradients in the overlying flow field. For small particle protrusions, this high-frequency region contributes a majority of the drag force variance, while the relative importance of the low-frequency drag force fluctuations increases with increasing protrusion. The amplitude of high-frequency drag force fluctuations is modulated by the VLSMs irrespective of particle protrusion. These results provide some insight into the mechanics of bed particle stability and indicate that the optimum conditions for particle entrainment may occur when a low-pressure region embedded in the high-velocity portion of a VLSM overlays a particle.

A practical method for combination of fatigue damage subjected to low–frequency and high–frequency Gaussian random processes

2016 ◽  
Vol 60 ◽  
pp. 47-60 ◽  
Author(s):  
Chaoshuai Han ◽  
Yongliang Ma ◽  
Xianqiang Qu ◽  
Mindong Yang ◽  
Peijiang Qin
Keyword(s):  
Fatigue Damage ◽  
High Frequency ◽  
Low Frequency ◽  
Practical Method ◽  
Random Processes

Simulations of high-resolution images of amorphous silicon films

1986 ◽  
Vol 44 ◽  
pp. 544-545
Author(s):  
G. Y. Fan ◽  
J. M. Cowley
Keyword(s):  
Electron Microscope ◽  
High Frequency ◽  
Fourier Transformation ◽  
Amorphous Materials ◽  
Low Frequency ◽  
Chromatic Aberration ◽  
Structure Information ◽  
Frequency Components ◽  
High Resolution Images ◽  
Spatial Frequency Spectrum

It is well known that the structure information on the specimen is not always faithfully transferred through the electron microscope. Firstly, the spatial frequency spectrum is modulated by the transfer function (TF) at the focal plane. Secondly, the spectrum suffers high frequency cut-off by the aperture (or effectively damping terms such as chromatic aberration). While these do not have essential effect on imaging crystal periodicity as long as the low order Bragg spots are inside the aperture, although the contrast may be reversed, they may change the appearance of images of amorphous materials completely. Because the spectrum of amorphous materials is continuous, modulation of it emphasizes some components while weakening others. Especially the cut-off of high frequency components, which contribute to amorphous image just as strongly as low frequency components can have a fundamental effect. This can be illustrated through computer simulation. Imaging of a whitenoise object with an electron microscope without TF limitation gives Fig. 1a, which is obtained by Fourier transformation of a constant amplitude combined with random phases generated by computer.

SEM image sharpness analysis

1996 ◽  
Vol 54 ◽  
pp. 142-143
Author(s):  
M. T. Postek ◽  
A. E. Vladar
Keyword(s):  
High Frequency ◽  
Low Frequency ◽  
Quantitative Information ◽  
Primary Electron ◽  
Image Sharpness ◽  
Critical Dimensions ◽  
Sem Image ◽  
Frequency Changes ◽  
Electron Microscopes ◽  
Scanning Electron

Fully automated or semi-automated scanning electron microscopes (SEM) are now commonly used in semiconductor production and other forms of manufacturing. The industry requires that an automated instrument must be routinely capable of 5 nm resolution (or better) at 1.0 kV accelerating voltage for the measurement of nominal 0.25-0.35 micrometer semiconductor critical dimensions. Testing and proving that the instrument is performing at this level on a day-by-day basis is an industry need and concern which has been the object of a study at NIST and the fundamentals and results are discussed in this paper.In scanning electron microscopy, two of the most important instrument parameters are the size and shape of the primary electron beam and any image taken in a scanning electron microscope is the result of the sample and electron probe interaction. The low frequency changes in the video signal, collected from the sample, contains information about the larger features and the high frequency changes carry information of finer details. The sharper the image, the larger the number of high frequency components making up that image. Fast Fourier Transform (FFT) analysis of an SEM image can be employed to provide qualitiative and ultimately quantitative information regarding the SEM image quality.

Real Ear Sound Pressure Levels Developed by Three Portable Stereo System Earphones

1992 ◽  
Vol 1 (4) ◽  
pp. 52-55 ◽  
Author(s):  
Gail L. MacLean ◽  
Andrew Stuart ◽  
Robert Stenstrom
Keyword(s):  
High Frequency ◽  
Sound Pressure ◽  
Low Frequency ◽  
Test System ◽  
Output Frequency ◽  
Frequency Effects ◽  
Adult Men ◽  
Frequency Responses ◽  
Significant Difference ◽  
Sound Pressure Levels

Differences in real ear sound pressure levels (SPLs) with three portable stereo system (PSS) earphones (supraaural [Sony Model MDR-44], semiaural [Sony Model MDR-A15L], and insert [Sony Model MDR-E225]) were investigated. Twelve adult men served as subjects. Frequency response, high frequency average (HFA) output, peak output, peak output frequency, and overall RMS output for each PSS earphone were obtained with a probe tube microphone system (Fonix 6500 Hearing Aid Test System). Results indicated a significant difference in mean RMS outputs with nonsignificant differences in mean HFA outputs, peak outputs, and peak output frequencies among PSS earphones. Differences in mean overall RMS outputs were attributed to differences in low-frequency effects that were observed among the frequency responses of the three PSS earphones. It is suggested that one cannot assume equivalent real ear SPLs, with equivalent inputs, among different styles of PSS earphones.

Evaluation of Special Hearing Aids for Deaf Children

1971 ◽  
Vol 36 (4) ◽  
pp. 527-537 ◽  
Author(s):  
Norman P. Erber
Keyword(s):  
Hearing Aids ◽  
High Frequency ◽  
Hearing Aid ◽  
Low Frequency ◽  
Acoustic Stimulation ◽  
Deaf Children ◽  
Frequency Range ◽  
Frequency Limit ◽  
Unpublished Studies ◽  
Published Research

Two types of special hearing aid have been developed recently to improve the reception of speech by profoundly deaf children. In a different way, each special system provides greater low-frequency acoustic stimulation to deaf ears than does a conventional hearing aid. One of the devices extends the low-frequency limit of amplification; the other shifts high-frequency energy to a lower frequency range. In general, previous evaluations of these special hearing aids have obtained inconsistent or inconclusive results. This paper reviews most of the published research on the use of special hearing aids by deaf children, summarizes several unpublished studies, and suggests a set of guidelines for future evaluations of special and conventional amplification systems.

Efeitos do Método Pilates sobre a variabilidade da frequência cardíaca, flexibilidade e variáveis antropométricas em indivíduos sedentários

2016 ◽  
Vol 17 (1) ◽  
pp. 66
Author(s):  
Maria Lina Silva Leite
Keyword(s):  
High Frequency ◽  
Low Frequency

O objetivo deste estudo foi avaliar os efeitos do Método Pilates sobre a variabilidade da frequência cardíaca, na flexibilidade e nas variáveis antropométricas em indivíduos sedentários. O presente estudo contou com 14 voluntárias do sexo feminino, na faixa etária entre 40 e 55 anos, que realizaram 20 sessões de exercícios do Método Pilates, duas vezes por semana, com duração de 45 minutos cada sessão, dividida em três fases: repouso, exercício e recuperação. As variáveis estudadas foram: os dados antropométricos, flexibilidade avaliada utilizando o teste de sentar-e-alcançar com o Banco de Wells, e intervalos R-R usando um cardiotacômetro. O processamento dos sinais da frequência cardíaca foi efetuado em ambiente MatLab 6.1®, utilizando a TWC. Os dados coletados foram submetidos ao teste de normalidade de Shapiro Wilk e foi utilizado o teste de Wilcoxon e Anova One Way (α = 0,05). Nos resultados, observou-se que não houve diferenças significativas entre os valores antropométricos e de frequência cardíaca, porém houve aumento da flexibilidade com o treinamento. Comparando a primeira e a vigésima sessão com relação aos parâmetros low frequency (LF), high frequency (HF), e relação LF/HF, não houve diferença na fase de repouso e foram constatadas diferenças significativas de LF (p = 0,04) e HF (p = 0,04) na fase de exercício e diferença significativa de LF/HF (p = 0,05) na fase de recuperação. Comparando os parâmetros nos períodos de repouso, exercícios e recuperação durante a primeira sessão e durante a vigésima sessão, não houve diferença significativa nos parâmetros LF, HF e LF/HF. Pode-se concluir que, em relação à flexibilidade, foi observada uma melhora significativa, enquanto a análise da frequência cardíaca caracterizou a intensidade do exercício de 50% da capacidade funcional das voluntárias. Em relação aos parâmetros LF, HF e LF/HF foram observados um aumento da variabilidade da frequência cardíaca, provavelmente produto da atividade do Método Pilates. A Transformada Wavelet (TWC) mostrou-se um Método adequado para as análises da variabilidade da frequência cardíaca.Palavras-chave: frequência cardíaca, Transformada Wavelet, Pilates.

Dynamics of the processes in metal machining

1998 ◽  
Vol 2 ◽  
pp. 115-122
Author(s):  
Donatas Švitra ◽  
Jolanta Janutėnienė
Keyword(s):  
High Frequency ◽  
Machine Tools ◽  
Metal Cutting ◽  
Cutting Tool ◽  
Low Frequency ◽  
Metal Cutting Machine ◽  
Cutting Machine ◽  
Metal Machining

In the practice of processing of metals by cutting it is necessary to overcome the vibration of the cutting tool, the processed detail and units of the machine tool. These vibrations in many cases are an obstacle to increase the productivity and quality of treatment of details on metal-cutting machine tools. Vibration at cutting of metals is a very diverse phenomenon due to both it’s nature and the form of oscillatory motion. The most general classification of vibrations at cutting is a division them into forced vibration and autovibrations. The most difficult to remove and poorly investigated are the autovibrations, i.e. vibrations arising at the absence of external periodic forces. The autovibrations, stipulated by the process of cutting on metalcutting machine are of two types: the low-frequency autovibrations and high-frequency autovibrations. When the low-frequency autovibration there appear, the cutting process ought to be terminated and the cause of the vibrations eliminated. Otherwise, there is a danger of a break of both machine and tool. In the case of high-frequency vibration the machine operates apparently quiently, but the processed surface feature small-sized roughness. The frequency of autovibrations can reach 5000 Hz and more.

Calculation-and-experimental estimation of the role of the frequency ratio in changing the endurance at two-frequency deformation modes

2019 ◽  
Vol 85 (1(I)) ◽  
pp. 64-71 ◽  
Author(s):  
M. M. Gadenin
Keyword(s):  
High Frequency ◽  
Experimental Studies ◽  
Low Frequency ◽  
Reduction Factor ◽  
Single Frequency ◽  
Cyclic Loads ◽  
Small Ratio ◽  
Harmonic Components ◽  
Deformation Modes

The cycle configuration at two-frequency loading regimes depends on the number of parameters including the absolute values of the frequencies and amplitudes of the low-frequency and high-frequency loads added during this mode, the ratio of their frequencies and amplitudes, as well as the phase shift between these harmonic components, the latter having a significant effect only with a small ratio of frequencies. Presence of such two-frequency regimes or service loading conditions for parts of machines and structures schematized by them can significantly reduce their endurance. Using the results of experimental studies of changes in the endurance of a two-frequency loading of specimens of cyclically stable, cyclically softened and cyclically hardened steels under rigid conditions we have shown that decrease in the endurance under the aforementioned conditions depends on the ratio of frequencies and amplitudes of operation low-frequency low-cycle and high-frequency vibration stresses, and, moreover, the higher the level of the ratios of amplitudes and frequencies of those stacked harmonic processes of loading the greater the effect. It is shown that estimation of such a decrease in the endurance compared to a single frequency loading equal in the total stress (strains) amplitudes can be carried out using an exponential expression coupling those endurances through a parameter (reduction factor) containing the ratio of frequencies and amplitudes of operation cyclic loads and characteristic of the material. The reduction is illustrated by a set of calculation-experimental curves on the corresponding diagrams for each of the considered types of materials and compared with the experimental data.

Sign in / Sign up

Export Citation Format

Share Document