Snap Loads on Mooring Lines of a Floating Offshore Wind Turbine Structure

2014 ◽  
Author(s):  
Wei-ting Hsu ◽  
Krish P. Thiagarajan ◽  
Matthew Hall ◽  
Michael MacNicoll ◽  
Richard Akers
Keyword(s):  
Wind Turbine ◽  
Impact Load ◽  
Offshore Wind ◽  
Mooring Line ◽  
Offshore Wind Turbine ◽  
Special Focus ◽  
Mooring Lines ◽  
Floating Offshore Wind Turbine ◽  
Marine Applications

There are a number of design challenges facing mooring systems of floating offshore wind turbine (FOWT) platforms in an offshore environment. Some unique aspects of the FOWT industry should be considered when examining applicability of established offshore mooring practices. Important among these are: economy and cost effectiveness; light weight minimal platforms; and water depths ranging from 50–300 m. A lighter displacement platform in shallow water, supported by lines with light to moderate pre-tension can result in a higher probability of slack line events and hence snap loads during re-engagement. Such loads can result in shock on the line material and considerably reduce the fatigue life. Such events have the potential to occur in various sea states, and not necessarily limited to extreme conditions. These conditions will be dependent on structure resonant motions, which are influenced by wind loads and moments, wave conditions and mooring line properties. Model tests of typical concepts for FOWT reported in literature have shown occasional slack line episodes. This paper is a review of literature on snap load occurrence in marine applications, including lifting and lowering operations, ROV and diving bell operations. This paper presents a case study of a FOWT. Special focus is on mooring systems which are affected by impact load conditions. Criteria are reviewed and consequences are documented.

scholarly journals Dynamic Response for a Submerged Floating Offshore Wind Turbine with Different Mooring Configurations

2019 ◽  
Vol 7 (4) ◽  
pp. 115 ◽  
Author(s):  
Yane Li ◽  
Conghuan Le ◽  
Hongyan Ding ◽  
Puyang Zhang ◽  
Jian Zhang
Keyword(s):  
Dynamic Response ◽  
Wind Turbine ◽  
Dynamic Responses ◽  
Offshore Wind ◽  
Mooring Line ◽  
Offshore Wind Turbine ◽  
Intermediate Water ◽  
Mooring System ◽  
Mooring Lines ◽  
Floating Offshore Wind Turbine

The paper discusses the effects of mooring configurations on the dynamic response of a submerged floating offshore wind turbine (SFOWT) for intermediate water depths. A coupled dynamic model of a wind turbine-tower-floating platform-mooring system is established, and the dynamic response of the platform, tensions in mooring lines, and bending moment at the tower base and blade root under four different mooring configurations are checked. A well-stabilized configuration (i.e., four vertical lines and 12 diagonal lines with an inclination angle of 30°) is selected to study the coupled dynamic responses of SFOWT with broken mooring lines, and in order to keep the safety of SFOWT under extreme sea-states, the pretension of the vertical mooring line has to increase from 1800–2780 kN. Results show that the optimized mooring system can provide larger restoring force, and the SFOWT has a smaller movement response under extreme sea-states; when the mooring lines in the upwind wave direction are broken, an increased motion response of the platform will be caused. However, there is no slack in the remaining mooring lines, and the SFOWT still has enough stability.

scholarly journals DeepCwind Semi-Submersible Floating Offshore Wind Turbine Platform with Nonlinear Multi-Segment Catenary Mooring Line and Intermediate Buoy

2021 ◽  
Author(s):  
mohammad motallebi ◽  
Hassan Ghassemi
Keyword(s):  
Adverse Effects ◽  
Wind Turbine ◽  
Water Depth ◽  
Offshore Wind ◽  
Correct Selection ◽  
Mooring Line ◽  
Offshore Wind Turbine ◽  
Mooring Lines ◽  
Floating Offshore Wind Turbine ◽  
Selection Of

In this paper, with the purpose of improving the mechanical behavior of DeepCwind semi-submersible floating offshore wind turbine (FOWT) platform mooring lines, nonlinear catenary cables of platform are divided into multi-segments and intermediate buoy. The mathematical formulations of the dynamic equation acted on the cable with buoys are described. Present study is employed to the OC4-DeepCwind semi-submersible FOWT platform. It is designed for 200-meter water depth with mooring lines consist of three catenary steel chain cables that have an angle of 120 degrees to each other. The dynamic response of multi-segment catenary mooring line with different buoys radiuses and different positions along the cables were investigated. The full-scale platform was modeled in ANSYS-AQWA software and the simulations are performed in harsh offshore. The tension, strain, anchor uplift, cable uplift for different buoy radiuses and its position along cable are presented and discussed. Moreover, platform motions at three directions (surge, heave and pitch) are also analyzed. It is concluded that by correct selection of the buoy volume and position along cable, the tension of the cable may be reduced up to 45%. By incorrect selection of the buoy, the results will cause adverse effects.

Coupled Dynamic Analysis for Multi-Unit Floating Offshore Wind Turbine in Maximum Operational and Survival Conditions

2015 ◽  
Author(s):  
H. K. Jang ◽  
H. C. Kim ◽  
M. H. Kim ◽  
K. H. Kim
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Time Domain ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Random Waves ◽  
Mooring Lines ◽  
Floating Offshore Wind Turbine ◽  
Coupled Dynamic Analysis ◽  
Floating Offshore Wind Turbines

Numerical tools for a single floating offshore wind turbine (FOWT) have been developed by a number of researchers, while the investigation of multi-unit floating offshore wind turbines (MUFOWT) has rarely been performed. Recently, a numerical simulator was developed by TAMU to analyze the coupled dynamics of MUFOWT including multi-rotor-floater-mooring coupled effects. In the present study, the behavior of MUFOWT in time domain is described through the comparison of two load cases in maximum operational and survival conditions. A semi-submersible floater with four 2MW wind turbines, moored by eight mooring lines is selected as an example. The combination of irregular random waves, steady currents and dynamic turbulent winds are applied as environmental loads. As a result, the global motion and kinetic responses of the system are assessed in time domain. Kane’s dynamic theory is employed to formulate the global coupled dynamic equation of the whole system. The coupling terms are carefully considered to address the interactions among multiple turbines. This newly developed tool will be helpful in the future to evaluate the performance of MUFOWT under diverse environmental scenarios. In the present study, the aerodynamic interactions among multiple turbines including wake/array effect are not considered due to the complexity and uncertainty.

Fatigue Analysis for Mooring System of a Spar-Type Floating Offshore Wind Turbine

2020 ◽  
Author(s):  
Xutian Xue ◽  
Xiaoyong Liu ◽  
Nian-Zhong Chen ◽  
Xifeng Gao
Keyword(s):  
Wind Turbine ◽  
Fatigue Analysis ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Safety Factors ◽  
Mooring Lines ◽  
Hydrodynamic Analysis ◽  
Floating Offshore Wind Turbine ◽  
Different Diameters ◽  
Rainflow Counting

Abstract This paper aims to perform a time-domain mooring fatigue analysis for a Spar-type floating offshore wind turbine operated in the South China Sea. Tension ranges of mooring lines are achieved from a hydrodynamic analysis where the effects of wind, wave and current are considered. A rainflow counting method is used to calculate the number of mooring tension cycles with corresponding ranges. The fatigue lives of mooring lines are then predicted by Palmgren-Miner’s rule according to T-N & S-N curves. A comparison of fatigue lives predicted by T-N & S-N curves-based approaches with/without considering safety factors is made. The results show that the T-N curves-based approach is more conservative than the S-N curves-based approach if safety factors are not considered in the two approaches, while the fatigue lives predicted by both approaches are in general comparable when the safety factors suggested by API and DNVGL are applied in the two approaches. A comparative study of three kinds of R4 grade studless mooring chains with different diameters (2.5-inch, 4-inch, 5-inch) is also conducted and the results show that the design with the 2.5-inch chain does not meet the fatigue requirements.

Dynamic Response of Spar-Type Floating Offshore Wind Turbine in Freak Wave

2019 ◽  
Author(s):  
Yougang Tang ◽  
Yan Li ◽  
Peng Xie ◽  
Xiaoqi Qu ◽  
Bin Wang
Keyword(s):  
Dynamic Response ◽  
Wind Turbine ◽  
Offshore Wind ◽  
Modulation Method ◽  
Power Coefficient ◽  
Offshore Wind Turbine ◽  
Floating Structure ◽  
Mooring Lines ◽  
Freak Wave ◽  
Floating Offshore Wind Turbine

Abstract Simulations are conducted in time domain to investigate the dynamic response of a SPAR-type floating offshore wind turbine under the scenarios with freak wave. Towards this end, a coupled aero-hydro numerical model is developed. The methodology includes a blade-element-momentum model for aerodynamics, a nonlinear model for hydrodynamics, a nonlinear restoring model of SPAR buoy, and a nonlinear algorithm for mooring cables. The OC3 Hywind SPAR-type FOWT is chosen as an example to study the dynamic response under the freak conditions, while the time series of freak wave is generated by the Random Frequency Components Selection Phase Modulation Method. The motions of platform, the tensions in the mooring lines and the power generation performance are documented in different cases. According to the simulations, it shows that the power coefficient of wind turbine decreased rapidly at the moment when freak wave acted on the floating structure.

VolturnUS 1:8: Conclusion of 18-Months of Operation of the First Grid-Connected Floating Wind Turbine Prototype in the Americas

2015 ◽  
Author(s):  
Anthony M. Viselli ◽  
Andrew J. Goupee ◽  
Habib J. Dagher ◽  
Christopher K. Allen
Keyword(s):  
Wind Turbine ◽  
Large Data ◽  
Full Scale ◽  
Offshore Wind ◽  
Mooring Line ◽  
Offshore Wind Turbine ◽  
Data Set ◽  
Floating Offshore Wind Turbine ◽  
The Past ◽  
Floating Wind Turbine

This paper presents an overview of the successful conclusion of 18 months of testing the first grid-connected floating offshore wind turbine prototype in the Americas. The prototype, called VolturnUS 1:8, was installed off Castine, Maine, USA. The prototype is a 1:8 scale prototype and serves to de-risk the deployment of a full-scale 6MW turbine. VolturnUS utilizes innovations in materials, construction, and deployment technologies such as a concrete semi-submersible hull and an advanced composite tower to reduce the costs of offshore wind. The prototype unit was designed following the American Bureau of Shipping (ABS) “Guide for Building and Classing Floating Offshore Wind Turbine Installations”. Froude scaling was used in designing the 1:8-scale VolturnUS prototype so that the motions of the prototype in the relatively protected site represent those of the full-scale unit in an open site farther offshore. During the past year, a comprehensive instrumentation package monitored key performance characteristics of the platform during operational, extreme, and survival storm conditions. Data collected include: wind speed, turbine power, rotor angular frequency, blade pitch, torque, acceleration; tower bending moment, 6 DOF accelerations at tower top and base, mooring line tensions, and wave elevation at the platform. During the past year the prototype has experienced many environments representative of scaled ABS design conditions including operational wind and sea-states, 50-year sea states and 500-year survival sea states. This large data set provides a unique view of a near full-scale floating wind turbine subjected to its prescribed environmental conditions. Inspections of the concrete hull following removal provided confirmation of material durability. Marine growth measurements provide data for future design efforts.

scholarly journals Numerical Analysis of a Catenary Mooring System Attached by Clump Masses for Improving the Wave-Resistance Ability of a Spar Buoy-Type Floating Offshore Wind Turbine

2019 ◽  
Vol 9 (6) ◽  
pp. 1075 ◽  
Author(s):  
Zhenqing Liu ◽  
Yuangang Tu ◽  
Wei Wang ◽  
Guowei Qian
Keyword(s):  
Wind Turbine ◽  
International Energy Agency ◽  
Wave Resistance ◽  
Offshore Wind ◽  
Irregular Waves ◽  
Mooring Line ◽  
Offshore Wind Turbine ◽  
Induced Response ◽  
Mooring Lines ◽  
Energy Agency

The International Energy Agency (IEA), under the auspices of their Offshore Code Comparison Collaboration (OC3) initiative, has completed high-level design OC-3 Hywind system. In this system the wind turbine is supported by a spar buoy platform, showing good wave-resistance performance. However, there are still large values in the motion of surge degree of freedom (DOF). Addition of clump masses on the mooring lines is an effective way of reducing the surge motion. However, the optimization of the locations where the clump masses are added is still not clear. In this study, therefore, an in-house developed code is verified by comparing the results of the original OC3 model with those by FAST. The improvement of the performance of this modified platform as a function of the location of the clump masses has been examined under three regular waves and three irregular waves. In the findings of these examination, it was apparent that attaching clump masses with only one-tenth of the mass of the total mooring-line effectively reduces the wave-induced response. Moreover, there is an obvious improvement as the depth of the location where the clump masses mounted is increased.

Sign in / Sign up

Export Citation Format

Share Document