Physical and Theoretical Modeling of Surface-Piercing Hydrofoils for a High-Speed Unmanned Surface Vessel

2012 ◽  
Author(s):  
Stefano Brizzolara ◽  
Yin Lu Young
Keyword(s):  
High Speed ◽  
Hydrodynamic Performance ◽  
Scaled Model ◽  
Mixture Flow ◽  
Numerical Predictions ◽  
University Of Berlin ◽  
Wide Range ◽  
Unmanned Surface Vessel ◽  
Ranse Solver ◽  
Surface Vessel

The objective of this work is to investigate the performance of two pairs of negative dihedral surface-piercing (SP) hydrofoils designed especially for an unmanned surface vessel with a top speed of 120 knots in sea state two. Physical modeling of a 1/6-scaled model of the SP hydrofoil was conducted at the free-surface cavitation tunnel at the Technical University of Berlin (TUB). The SP hydrofoil feature a new type of super-cavitating profile with an annex tapered trailing edge to achieve good efficiencies in foil born conditions (60–120 knots, super-cavitating/ super-ventilated regimes), as well as at take-off speeds (25–40 knots, wetted and/or partial-cavitating regimes). Preliminary results showed interesting anomalies in the trends of the measured forces with respect to the cavitation number and angle of attack for a wide range of inflow speeds. Details of the experimental study are presented along with numerical predictions obtained using finite volume RANSE solver with a volume of fluid technique to allow for a mixture flow with air/vapor and water phases. Explanation of the anomalies in the hydrodynamic performance is given.

Finite element modelling for orthogonal machining of AA2024-T351 alloy with an advanced fracture criterion

2021 ◽  
pp. 1-41
Author(s):  
Prudvi Reddy Paresi ◽  
N. Arunachalam ◽  
Yanshan Lou ◽  
Jeong Whan Yoon
Keyword(s):  
Constitutive Model ◽  
Strain Rate ◽  
High Speed ◽  
Fracture Criterion ◽  
Numerical Models ◽  
Machining Simulation ◽  
Experimental Conditions ◽  
Orthogonal Machining ◽  
Numerical Predictions ◽  
Wide Range

Abstract Numerical modelling of the plastic deformation and fracture during the high speed machining is highly challengeable. Consequently, there is a need for an advanced constitutive model and fracture criterion to make the numerical models more reliable. The aim of the present study is to extend the recent advanced static Lou-Yoon-Huh (LYH) ductile fracture creation to high strain rate and temperature applications such as machining. In the present work, the LYH static fracture creation was extended to machining conditions by introducing strain rate and temperature dependency terms. This extended LYH fracture criterion was calibrated over the wide range of stress triaxialities and different temperatures. Modified Khan- Huang-Liang (KHL) constitutive model along with the variable friction model was employed to predict the flow behaviour of work material during the machining simulation. Damage evolution method was coupled to identify the element deletion point during the machining simulation. Orthogonal machining experiments were carried out for an aerospace grade AA2024-T351 at cutting speeds varying between 100 and 400m/min with the feed rates varying between 0.1 and 0.3mm/rev. To assess the prediction capabilities of extended LYH fracture criterion numerical simulations were also carried out using Johnson-Cook (JC) fracture criterion under all experimental conditions. Specific cutting energy, chip morphology and compression ratio predictions were compared with the experimental data. Numerical predictions with coupled extended LYH criterion showed good agreement with experimental results compared to coupled JC fracture criterion.

Influence of Stator Blade Geometry on Torque Converter Cavitation

2017 ◽  
Vol 140 (4) ◽  
Author(s):  
Cheng Liu ◽  
Wei Wei ◽  
Qingdong Yan ◽  
Brian K. Weaver ◽  
Houston G. Wood
Keyword(s):  
High Speed ◽  
Torque Converter ◽  
Operating Conditions ◽  
Hydrodynamic Performance ◽  
Speed Ratio ◽  
Capacity Loss ◽  
Wide Range ◽  
Stator Blade ◽  
Torque Converters ◽  
Blade Geometry

Cavitation in torque converters may cause degradation in hydrodynamic performance, severe noise, or even blade damage. Researches have highlighted that the stator is most susceptible to the occurrence of cavitation due to the combination of high flow velocities and high incidence angles. The objective of this study is to therefore investigate the effects of cavitation on hydrodynamic performance as well as the influence of stator blade geometry on cavitation. A steady-state homogeneous computational fluid dynamics (CFD) model was developed and validated against test data. It was found that cavitation brought severe capacity constant degradation under low-speed ratio (SR) operating conditions and vanished in high-speed ratio operating conditions. A design of experiments (DOE) study was performed to investigate the influence of stator design variables on cavitation over various operating conditions, and it was found that stator blade geometry had a significant effect on cavitation behavior. The results show that stator blade count and leaning angle are important variables in terms of capacity constant loss, torque ratio (TR) variance, and duration of cavitation. Large leaning angles are recommended due to their ability to increase the cavitation number in torque converters over a wide range of SRs, leading to less stall capacity loss as well as a shorter duration of cavitation. A reduced stator blade count is also suggested due to a reduced TR loss and capacity loss at stall.

scholarly journals Mixing of complex fluids with coaxial mixers composed of two central impellers and an anchor

2021 ◽  
Author(s):  
Argang Kazemzadeh
Keyword(s):  
High Speed ◽  
Complex Fluids ◽  
Operating Conditions ◽  
Newtonian Fluids ◽  
Hydrodynamic Performance ◽  
Mixing Efficiency ◽  
Efficient System ◽  
Wide Range ◽  
Coaxial Mixers ◽  
Pseudoplastic Fluids

The coaxial mixers composed of a high-speed central impeller and a low-speed anchor have been recommended by the previous researchers for the mixing of highly viscous and non-Newtonian fluids. However, no study has been reported in the literature regarding the use of the coaxial mixing systems composed of two central impellers and an anchor in the agitation of complex fluids. Thus, the main objective of this study was to investigate the performance of coaxial mixers composed of two central impellers and an anchor in the agitation of the xanthan gum solution, which is a yield-pseudoplastic fluid, through electrical resistance tomography (ERT), the computational fluid dynamics (CFD), and design of experiments (DOE) combined with the response surface methodology (RSM). In the first stage of this study, the hydrodynamic performance of coaxial mixers, the single and double Scaba impellers in combination with an anchor impeller, was investigated in the mixing of yield-pseudoplastic fluids. Considering the mixing efficiency criteria, it was found that the double Scaba-anchor coaxial system was more efficient than the single Scaba-anchor coaxial mixer in the mixing of yield pseudoplastic fluids with regard to the mixing time and power drawn. In the second stage of this research project, the performances of three different coaxial mixers, namely, double Scaba-anchor coaxial (DSAC), double Rushton turbine-anchor coaxial (DRAC), and double pitched blade turbine-anchor coaxial (DPAC) mixers were assessed. It was found that the double Scaba-anchor coaxial (DSAC) mixer was more efficient system compared to the others at the same operating conditions. To evaluate the influence of the impeller spacing on the hydrodynamics of the double Scaba-anchor coaxial mixer, the lower impeller clearance and the spacing between two central impellers were changed within a wide range. The results demonstrated that a coaxial mixer with the impeller spacing of almost equal to the central impeller diameter was the most efficient configuration compared to the other cases. When the impeller spacing was varied, the merging flow and parallel flow patterns were observed. Finally, the hydrodynamic performances of different configurations of coaxial mixers composed of a wall scraping anchor impeller in combination with two different or identical central high-speed impellers were analyzed. The coaxial mixers utilized in this stage were the Scaba–Scaba-anchor (SSAC), Scaba-Rushton-anchor (SRAC), Rushton-Scaba-anchor (RSAC), Scaba-pitched blade-anchor (SPBAC), and pitched blade-Scaba-anchor (PBSAC). A new correlation was introduced for these complex configurations of the coaxial mixers by incorporating the Metzner-Otto constants (Ks) of the different types of the central impellers into the Reynolds number. The analysis of the collected data revealed that the Scaba-pitched blade-anchor coaxial (SPBAC) mixer was the most efficient mixing system in the mixing of the highly viscous non-Newtonian fluids.

Comparative Performance of Optimum High Speed SWATH and Semi-SWATH in Calm Water and in Waves

2015 ◽  
Author(s):  
S. Brizzolara ◽  
G. Vernengo ◽  
L. Bonfiglio ◽  
D. Bruzzone
Keyword(s):  
High Speed ◽  
Hydrodynamic Performance ◽  
Forward Speed ◽  
Comparative Performance ◽  
Hull Form ◽  
High Speeds ◽  
Head Waves ◽  
Calm Water ◽  
Minimization Algorithms ◽  
Ranse Solver

The hydrodynamic performance of unconventional SWATH and Semi-SWATH for high speed applications are analyzed and compared in this paper. Bare hull resistance in calm water is estimated by an inviscid boundary element method with viscous corrections and verified by a fully turbulent, multiphase unsteady RANSE solver. Motions response in head waves, calculated by a frequency domain 3D panel method with forward speed effects are also evaluated and compared. Both considered hulls are the best designs coming from full parametric hull form optimization procedures, based on CFD solvers for the estimation of their hydrodynamic performance and driven by evolutionary minimization algorithms. The SWATH has twin parabolic struts and an unconventional underwater shape, the semi-SWATH has a slender triangular waterline, a bulbous shape in the entrance body which gradually morph into a U-section with a shallow transom in the run body. In general, as expected, the Semi-SWATH hull shows a lower drag at high speeds while the single strut SWATH is superior at lower speeds. As regards seakeeping, the SWATH shows unbeatable lower pitch and heave motions in shorter waves, where the Semi-SWATH evidences a double peaked RAO. More detailed analysis and conclusion are drawn in the paper.

scholarly journals An assessment of the laminar kinetic energy concept for the prediction of high-lift, low-Reynolds number cascade flows

2011 ◽  
Vol 225 (7) ◽  
pp. 995-1003 ◽  
Author(s):  
R Pacciani ◽  
M Marconcini ◽  
A Arnone ◽  
F Bertini
Keyword(s):  
Reynolds Number ◽  
Kinetic Energy ◽  
High Speed ◽  
Low Reynolds Number ◽  
Flow Region ◽  
Freestream Turbulence ◽  
High Lift ◽  
Numerical Predictions ◽  
Wide Range ◽  
Low Reynolds

The laminar kinetic energy (LKE) concept has been applied to the prediction of low-Reynolds number flows, characterized by separation-induced transition, in high-lift airfoil cascades for aeronautical low-pressure turbine applications. The LKE transport equation has been coupled with the low-Reynolds number formulation of the Wilcox's k − ω turbulence model. The proposed methodology has been assessed against two high-lift cascade configurations, characterized by different loading distributions and suction-side diffusion rates, and tested over a wide range of Reynolds numbers. The aft-loaded T106C cascade is studied in both high- and low-speed conditions for several expansion ratios and inlet freestream turbulence values. The front-loaded T108 cascade is analysed in high-speed, low-freestream turbulence conditions. Numerical predictions with steady inflow conditions are compared to measurements carried out by the von Kármán Institute and the University of Cambridge. Results obtained with the proposed model show its ability to predict the evolution of the separated flow region, including bubble-bursting phenomenon and the formation of open separations, in high-lift, low-Reynolds number cascade flows.

Fluid-Film Journal Bearings Operating in a Hybrid Mode: Part I—Theoretical Analysis and Design

1981 ◽  
Vol 103 (4) ◽  
pp. 558-565 ◽  
Author(s):  
D. Koshal ◽  
W. B. Rowe
Keyword(s):  
High Speed ◽  
Journal Bearings ◽  
Hydrodynamic Performance ◽  
Total Power ◽  
Theoretical Treatment ◽  
Power Ratio ◽  
Eccentricity Ratio ◽  
Analysis And Design ◽  
System A ◽  
Wide Range

Oil-lubricated plain hybrid journal bearings have been investigated theoretically and experimentally to determine the hybrid (hydrostatic/hydrodynamic) performance. The paper consists of two parts: Part I deals with the theoretical treatment of results, and Part II describes the experimental investigation. It is demonstrated that when two rows of inlet lubricant sources are employed in a plain hybrid bearing, greater load-carrying capacity is obtained by positioning the entries near the ends of the bearing rather than at the center or at quarter stations. These results extend previous work by presenting data for a wide range of power ratio (K). The parameter K is defined as the ratio of friction power to pumping power. Increasing K has the same effect as increasing speed for a particular bearing system. A new basis for optimizing hybrid bearings is described. The bearings to be optimized are compared with a reference bearing, on a basis of load/total power; a technique which is not required in other bearings where load does not increase rapidly with power ratio. Plain hybrid bearings are compared with conventional recessed hydrostatic journal bearings and with axial groove hydrodynamic journal bearings. It is found that plain hybrid bearings are superior in performance to recessed journal bearings at low eccentricity ratio and low speed. Also plain hybrid bearings are comparable to axial groove hydrodynamic journal bearings at a high eccentricity ratio and high speed with advantages for variable directions of loading. Furhermore the hydrostatic effect tends to raise the whirl onset speed.

scholarly journals Marine Turbine Hydrodynamics by a Boundary Element Method with Viscous Flow Correction

2018 ◽  
Author(s):  
Francesco Salvatore ◽  
Zohreh Sarichloo ◽  
Danilo Calcagni
Keyword(s):  
Viscous Flow ◽  
Numerical Models ◽  
Turbine Blades ◽  
Integral Equation Method ◽  
Boundary Integral ◽  
Operating Conditions ◽  
Hydrodynamic Performance ◽  
Numerical Predictions ◽  
Wide Range ◽  
Marine Current

A computational methodology for the hydrodynamic analysis of horizontal axis marine current turbines is presented. The approach is based on a boundary integral equation method for inviscid flows originally developed for marine propellers and adapted here to describe the flow features that characterize hydrokinetic turbines. To this purpose, semi-analytical trailing wake and viscous-flow correction models are introduced. A validation study is performed by comparing hydrodynamic performance predictions with two experimental test cases and with results from other numerical models in the literature. The capability of the proposed methodology to correctly describe turbine thrust and power over a wide range of operating conditions is discussed. Viscosity effects associated to blade flow separation and stall are taken into account and predicted thrust and power are comparable with results of blade element methods that are largely used in the design of marine current turbines. The accuracy of numerical predictions tend to reduce in cases where turbine blades operate in off-design conditions.

scholarly journals Mixing of complex fluids with coaxial mixers composed of two central impellers and an anchor

2021 ◽  
Author(s):  
Argang Kazemzadeh
Keyword(s):  
High Speed ◽  
Complex Fluids ◽  
Operating Conditions ◽  
Newtonian Fluids ◽  
Hydrodynamic Performance ◽  
Mixing Efficiency ◽  
Efficient System ◽  
Wide Range ◽  
Coaxial Mixers ◽  
Pseudoplastic Fluids

The coaxial mixers composed of a high-speed central impeller and a low-speed anchor have been recommended by the previous researchers for the mixing of highly viscous and non-Newtonian fluids. However, no study has been reported in the literature regarding the use of the coaxial mixing systems composed of two central impellers and an anchor in the agitation of complex fluids. Thus, the main objective of this study was to investigate the performance of coaxial mixers composed of two central impellers and an anchor in the agitation of the xanthan gum solution, which is a yield-pseudoplastic fluid, through electrical resistance tomography (ERT), the computational fluid dynamics (CFD), and design of experiments (DOE) combined with the response surface methodology (RSM). In the first stage of this study, the hydrodynamic performance of coaxial mixers, the single and double Scaba impellers in combination with an anchor impeller, was investigated in the mixing of yield-pseudoplastic fluids. Considering the mixing efficiency criteria, it was found that the double Scaba-anchor coaxial system was more efficient than the single Scaba-anchor coaxial mixer in the mixing of yield pseudoplastic fluids with regard to the mixing time and power drawn. In the second stage of this research project, the performances of three different coaxial mixers, namely, double Scaba-anchor coaxial (DSAC), double Rushton turbine-anchor coaxial (DRAC), and double pitched blade turbine-anchor coaxial (DPAC) mixers were assessed. It was found that the double Scaba-anchor coaxial (DSAC) mixer was more efficient system compared to the others at the same operating conditions. To evaluate the influence of the impeller spacing on the hydrodynamics of the double Scaba-anchor coaxial mixer, the lower impeller clearance and the spacing between two central impellers were changed within a wide range. The results demonstrated that a coaxial mixer with the impeller spacing of almost equal to the central impeller diameter was the most efficient configuration compared to the other cases. When the impeller spacing was varied, the merging flow and parallel flow patterns were observed. Finally, the hydrodynamic performances of different configurations of coaxial mixers composed of a wall scraping anchor impeller in combination with two different or identical central high-speed impellers were analyzed. The coaxial mixers utilized in this stage were the Scaba–Scaba-anchor (SSAC), Scaba-Rushton-anchor (SRAC), Rushton-Scaba-anchor (RSAC), Scaba-pitched blade-anchor (SPBAC), and pitched blade-Scaba-anchor (PBSAC). A new correlation was introduced for these complex configurations of the coaxial mixers by incorporating the Metzner-Otto constants (Ks) of the different types of the central impellers into the Reynolds number. The analysis of the collected data revealed that the Scaba-pitched blade-anchor coaxial (SPBAC) mixer was the most efficient mixing system in the mixing of the highly viscous non-Newtonian fluids.

Microfabrication research at the National Submicron Facility

1983 ◽  
Vol 41 ◽  
pp. 86-89
Author(s):  
E.D. Wolf
Keyword(s):  
Integrated Circuits ◽  
Particle Physics ◽  
High Speed ◽  
New Technology ◽  
High Energy ◽  
High Energy Particle ◽  
New Science ◽  
Wide Range ◽  
Intermediate Domain ◽  
Circuit Function

Most microelectronics devices and circuits operate faster, consume less power, execute more functions and cost less per circuit function when the feature-sizes internal to the devices and circuits are made smaller. This is part of the stimulus for the Very High-Speed Integrated Circuits (VHSIC) program. There is also a need for smaller, more sensitive sensors in a wide range of disciplines that includes electrochemistry, neurophysiology and ultra-high pressure solid state research. There is often fundamental new science (and sometimes new technology) to be revealed (and used) when a basic parameter such as size is extended to new dimensions, as is evident at the two extremes of smallness and largeness, high energy particle physics and cosmology, respectively. However, there is also a very important intermediate domain of size that spans from the diameter of a small cluster of atoms up to near one micrometer which may also have just as profound effects on society as “big” physics.

Assessment of Commercial Off-the-Shelf Tissue Adhesives for Sealing Military-Relevant Corneal Perforation Injuries

2021 ◽  
Author(s):  
Eric J Snider ◽  
Lauren E Cornell ◽  
Brandon M Gross ◽  
David O Zamora ◽  
Emily N Boice
Keyword(s):  
Intraocular Pressure ◽  
High Speed ◽  
Anterior Segment ◽  
Ocular Tissue ◽  
Corneal Tissue ◽  
Corneal Perforation ◽  
Tissue Adhesives ◽  
Open Globe ◽  
Wide Range ◽  
Commercial Off The Shelf

ABSTRACT Introduction Open-globe ocular injuries have increased in frequency in recent combat operations due to increased use of explosive weaponry. Unfortunately, open-globe injuries have one of the worst visual outcomes for the injured warfighter, often resulting in permanent loss of vision. To improve visual recovery, injuries need to be stabilized quickly following trauma, in order to restore intraocular pressure and create a watertight seal. Here, we assess four off-the-shelf (OTS), commercially available tissue adhesives for their ability to seal military-relevant corneal perforation injuries (CPIs). Materials and Methods Adhesives were assessed using an anterior segment inflation platform and a previously developed high-speed benchtop corneal puncture model, to create injuries in porcine eyes. After injury, adhesives were applied and injury stabilization was assessed by measuring outflow rate, ocular compliance, and burst pressure, followed by histological analysis. Results Tegaderm dressings and Dermabond skin adhesive most successfully sealed injuries in preliminary testing. Across a range of injury sizes and shapes, Tegaderm performed well in smaller injury sizes, less than 2 mm in diameter, but inadequately sealed large or complex injuries. Dermabond created a watertight seal capable of maintaining ocular tissue at physiological intraocular pressure for almost all injury shapes and sizes. However, application of the adhesive was inconsistent. Histologically, after removal of the Dermabond skin adhesive, the corneal epithelium was removed and oftentimes the epithelium surface penetrated into the wound and was adhered to inner stromal tissue. Conclusions Dermabond can stabilize a wide range of CPIs; however, application is variable, which may adversely impact the corneal tissue. Without addressing these limitations, no OTS adhesive tested herein can be directly translated to CPIs. This highlights the need for development of a biomaterial product to stabilize these injuries without causing ocular damage upon removal, thus improving the poor vision prognosis for the injured warfighter.

Sign in / Sign up

Export Citation Format

Share Document