Slamming Simulations in a Conditional Wave

2012 ◽  
Author(s):  
Sopheak Seng ◽  
Jørgen Juncher Jensen
Keyword(s):  
Bending Moment ◽  
Body Motion ◽  
Correction Coefficient ◽  
Container Ship ◽  
Cfd Simulations ◽  
Strip Theory ◽  
Structural Responses ◽  
Cfd Method ◽  
Extreme Responses ◽  
Vertical Bending Moment

A study of slamming events in conditional waves is presented in this paper. The ship is sailing in head sea and the motion is solved for under the assumption of rigid body motion constrained to two degree-of-freedom i.e. heave and pitch. Based on a time domain non-linear strip theory most probable conditional waves are generated to induce short term extreme responses of 4500 MNm sagging and hogging vertical bending moment (VBM) amidships on a modern 9,400-TEU post-Panamax container ship and 3000 MNm (sag) on a Panamax container ship. The results of the strip theory are compared to the results of free surface NS/VOF CFD simulations under the same wave conditions. In moderate seas and no occurrence of slamming the structural responses predicted by the methods agree well. When slamming occurs the strip theory overpredicts VBM but the peak values of VBM occurs at approximately the same time as predicted by the CFD method implying the possibility to use the more accurate CFD results to improve the estimation of slamming loads in the strip theory through a rational correction coefficient.

Time Domain Comparison With Experiments for Ship Motions and Structural Loads on a Container Ship in Abnormal Waves

2011 ◽  
Author(s):  
Suresh Rajendran ◽  
Nuno Fonseca ◽  
C. Guedes Soares ◽  
Gu¨nther F. Clauss ◽  
Marco Klein
Keyword(s):  
Time Domain ◽  
Bending Moment ◽  
Green Water ◽  
Ship Motions ◽  
Container Ship ◽  
Wave Elevation ◽  
Strip Theory ◽  
The Time Domain ◽  
Vertical Bending Moment ◽  
Comparison With Experiments

The paper presents experimental results from model tests with a containership advancing in abnormal wave conditions and comparisons with numerical simulations. A nonlinear time domain method based on strip theory is used for the calculation of vertical ship responses induced by abnormal waves. This code combines the linear diffraction and radiation forces with dominant nonlinear forces associated with vertical response arising from Froude-Krylov forces, hydrostatic forces and shipping of green water. The time domain simulations are compared directly with experimental records from tests with a model of a container ship in deterministic waves for a range of Froude numbers. Extreme sea conditions were replicated by the reproduction of realistic abnormal waves like the New Year Wave and abnormal wave from North Alwyn. Head sea condition is considered and the comparisons include the wave elevation, the vertical motions of the ship and the vertical bending moment at midship.

Response Based Identification of Critical Wave Scenarios

2012 ◽  
Author(s):  
Günther F. Clauss ◽  
Marco Klein ◽  
Carlos Guedes Soares ◽  
Nuno Fonseca
Keyword(s):  
Linear Method ◽  
Bending Moment ◽  
Extreme Wave ◽  
Offshore Structure ◽  
Sea State ◽  
Worst Case ◽  
Strip Theory ◽  
Wave Conditions ◽  
Vertical Bending Moment ◽  
Method Approach

In the last years the identification and investigation of critical wave sequences regarding offshore structure responses became one of the main topics in the ocean engineering community. Thereby the area of interest covers the entire field of application spectra at sea — from efficient and economic offshore operations in moderate sea states to reliability as well as survival in extreme wave conditions. For most cases, the focus lies on limiting criteria for the design, such as maximum global loads, maximum relative motions between two or more vessels or maximum accelerations, at which the floating structure has to operate or to survive. These criteria are typically combined with a limiting characteristic sea state (Hs, Tp) or a rogue wave. For the investigation of offshore structures as well as the identification of critical wave sequences, different approaches are available — most of them are based on linear transfer functions as it is an efficient procedure for the fast holistic evaluation. But, for some cases the linear method approach implies uncertainties due to nonlinear response behavior, in particular in extreme wave conditions. This paper presents an approach to these challenges, a response based optimization tool for critical wave sequence detection. This tool, which has been successfully introduced for the evaluation of the applicability of a multi-body system based on the linear method approach, is adjusted to a nonlinear task — the vertical bending moment of a chemical tanker in extreme wave conditions. Therefore a nonlinear strip theory solver is introduced into the optimization routine to capture the nonlinear effects on the vertical bending moment due to steep waves acting on large bow flares. The goal of the procedure is to find a worst case wave sequence for a certain critical sea state. This includes intensive numerical investigation as well as model test validation.

Steep Wave Effects on Wave Induced Vertical Bending Moment Using a 3D Numerical Wave Tank

2017 ◽  
Author(s):  
Shivaji Ganesan Thirunaavukarasu ◽  
Debabrata Sen ◽  
Yogendra Parihar
Keyword(s):  
Comparative Study ◽  
Incident Wave ◽  
Bending Moment ◽  
Wave Steepness ◽  
Numerical Wave Tank ◽  
Wave Tank ◽  
Strip Theory ◽  
Numerical Wave ◽  
Wave Induced ◽  
Vertical Bending Moment

This paper presents a detail comparative study on wave induced vertical bending moment (VBM) between linear and approximate nonlinear calculations using a 3D numerical wave tank (NWT) method. The developed numerical approach is in time domain where the ambient incident waves can be defined by any suitable wave theory. Certain justifying approximations employed in the solution of the interaction hydrodynamics (diffraction and radiation) enabling the NWT to generate stable long duration time histories of all parameters of interest. This is an extension of our earlier works towards the development of a practical NWT based solution for wave-structure interactions [1]. After a brief outline of the implemented numerical details, a comprehensive validation and verification of vertical shear force (VSF) and bending moment RAOs computed using the linearized version of the NWT against the usual linear results of strip theory and 3D panel codes are presented. Next we undertake the comparative study between the fully linear and approximate nonlinear versions of the present code for different incident wave steepness. In the approximate nonlinear formulation, the ambient incident wave is defined by the full nonlinear numerical wave model based on Fourier approximation method which can generate very steep steady periodic nonlinear waves up to the near wave breaking limit. The nonlinearities associated with the incident Froude Krylov and hydrostatic restoring forces/moments are exact up to the instantaneous wetted surface at the displaced location, but the hydrodynamic diffraction and radiation effects are linearized around the mean wetted surface. The standard S175 container hull is considered for the comparative studies because of its geometric nonlinearities. Numerical simulations are performed for four different wave lengths with increasing wave steepness. It is observed that the computed wave induced VBM amidships from the approximate nonlinear results can be almost 30% higher compared to the results from a purely linear solution, which can be a critical issue from the safety point. Significant higher harmonics are also observed in the approximate nonlinear results which at some times may be responsible for exciting the undesirable whipping/springing responses.

Influence of Whipping on Long-term Vertical Bending Moment

2004 ◽  
Vol 48 (04) ◽  
pp. 261-272
Author(s):  
Gro Sagli Baarholm ◽  
Jørgen Juncher Jensen
Keyword(s):  
Nonlinear Response ◽  
Extreme Values ◽  
Bending Moment ◽  
Sea Waves ◽  
Short Term ◽  
Strip Theory ◽  
Long Time ◽  
Wave Induced ◽  
Vertical Bending Moment

This paper is concerned with estimating the response value corresponding to a long return period, say 20 years. Time domain simulation is required to obtain the nonlinear response, and long time series are required to limit the statistical uncertainty in the simulations. It is crucial to introduce ways to improve the efficiency in the calculation. A method to determine the long-term extremes by considering only a few short-term sea states is applied. Long-term extreme values are estimated using a set of sea states that have a certain probability of occurrence, known as the contour line approach. Effect of whipping is included by assuming that the whipping and wave-induced responses are independent, but the effect of correlation of the long-term extreme value is also studied. Numerical calculations are performed using a nonlinear, hydroelastic strip theory as suggested by Xia et al (1998). Results are presented for the S-175 containership (ITTC 1983) in head sea waves. The analysis shows that whipping increases the vertical bending moment and that the correlation is significant.

Determination of global design loads for large high-speed catamarans

2002 ◽  
Vol 216 (1) ◽  
pp. 79-94
Author(s):  
S E Heggelund ◽  
T Moan ◽  
S Oma
Keyword(s):  
High Speed ◽  
Bending Moment ◽  
Wave Loads ◽  
Strip Theory ◽  
Non Linear ◽  
Design Loads ◽  
Linear Effects ◽  
Operational Criteria ◽  
Vertical Bending Moment

Methods for calculation of design loads for high-speed vessels are investigated. The influence of operational restrictions on design loads is emphasized. Relevant operational criteria for high-speed displacement vessels are discussed. Procedures and criteria for numerical calculation of operational limits are incomplete and should be further investigated. Operational limits and design loads for a 60 m catamaran are calculated on the basis of linear strip theory. Non-linear effects on design loads are assessed from calculations in regular waves. Simplified formulae commonly used by classification societies for prediction of operational limits seem to over-predict the reduction of motions and wave loads at reduced speed. When operational limits typically given by the shipmaster or the operator are used, the design loads found by direct calculations are comparable with design loads given by classification societies. For vertical bending moment and torsion, the use of active foils is found to increase the linear loads. Owing to reduced motions, the foils reduce the non-linear loads and hence the total loads. The effect of non-linear horizontal loads is not investigated but can be important for transverse bending moment.

scholarly journals Simulation based calculation of ship motions in extreme seas with a body-exact strip theory approach

Pomorstvo ◽  
2021 ◽  
Vol 35 (1) ◽  
pp. 36-48
Author(s):  
Kıvanç Ali Anil ◽  
Devrim Bülent Danışman ◽  
Kadir Sarıöz
Keyword(s):  
Bending Moment ◽  
Computer Experiments ◽  
Ship Motions ◽  
Theory Approach ◽  
Seakeeping Performance ◽  
Strip Theory ◽  
Simulation Based ◽  
Consistent Assessment ◽  
Extreme Responses ◽  
Ship Hydroelasticity

For all design phases of naval vessels, the fidelity of seakeeping calculations in extreme seas is open to discussion due to the inadequacy of the linear theory of ship motions. Currently the computer-generated time series of ship responses and wave height (the real time computer experiments) are utilized to calculate the distribution of the vertical distortion, shear force and bending moment by means of “ship hydroelasticity theory”. Inspired by these studies a simulation based calculation of symmetric ship motions is performed in long crested irregular head seas, in addition with a body-exact strip theory approach. The scope of this study is limited to the ship motions only. Verification is achieved utilizing the spectral analysis procedure which contains the discrete Fourier transform (DFT) and the smoothing algorithms. The results are compared with the experimental data, and the ANSYS AQWA software results. The simulation results provide adequate data for the extreme responses. This state-of-the-art method in addition with a “body-exact strip theory approach” ensures the consistent assessment of the seakeeping performance in extreme sea condition. As a result, it is evaluated that this calculation method can be used in the design stages of naval platforms.

Analysis of Vertical Bending Moment on an Ultra Large Containership Induced by Extreme Head Seas

2014 ◽  
Author(s):  
Suresh Rajendran ◽  
Nuno Fonseca ◽  
C. Guedes Soares
Keyword(s):  
Rigid Body ◽  
Bending Moment ◽  
Variable Stiffness ◽  
The Body ◽  
Experimental Results ◽  
Irregular Waves ◽  
Time Step ◽  
Strip Theory ◽  
Vertical Bending Moment ◽  
Body Response

This paper discusses the numerical analysis of an ultra large containership model in severe head seas. A body nonlinear time domain code based on the strip theory is used for the calculation of the rigid body response of the vessel. The radiation, diffraction, Froude-krylov and hydrostatic forces are calculated for the exact wetted surface area of the ship at each time step. A practical engineering approach is followed to calculate the body nonlinear radiation and diffraction forces. The numerical vertical bending moment is compared with the experimental results. The experiment was conducted on a flexible model in both regular and irregular waves. The model comprised six segments that were joined with an aluminum backbone of variable stiffness characteristics in order to replicate the hydroelastic behavior of the real ship. The model was tested for two ship speeds, 15 and 22 knots. For the first three harmonic values of the vertical bending moment, a good agreement between the numerical and the experimental results are found. However, higher harmonics significantly contributed to the total experimental vertical bending moment, in regular waves with 8m wave height and a ship speed of 15 knots. Similarly, the value of the fourth harmonic was 32% of the first harmonic values when the ship encountered a 5m regular wave with 22 knots speed. On comparison of the rigid body response in irregular seas, the hydroelastic loads resulted in 49% increase in the maximum value of the vertical bending moment.

Calculation of Vertical Bending Moment Acting on an Ultra Large Containership in Large Amplitude Waves

2015 ◽  
Author(s):  
Suresh Rajendran ◽  
Nuno Fonseca ◽  
C. Guedes Soares
Keyword(s):  
Large Amplitude ◽  
Bending Moment ◽  
Regular Waves ◽  
Structural Dynamic ◽  
Strip Theory ◽  
Structural Dynamic Characteristics ◽  
Wetted Surface Area ◽  
The Time Domain ◽  
Hydroelastic Response ◽  
Vertical Bending Moment

The time domain method is further extended here in order to calculate the hydroelastic response of an ultra large containership in regular waves. Based on strip theory, the hydrodynamic and the hydrostatic forces are calculated for the instantaneous wetted surface area. Slamming forces are calculated using a Von Karman approach in which the water pile up during slamming is neglected. Timoshenko beam which takes into account the shear deformation and rotary inertia is used to model the structural dynamic characteristics of the hull. The beam is discretized using the finite element method and the ship vibration is solved using the modal analysis. The method is used to calculate the vertical bending moment acting on an ultra large containership in large amplitude regular waves. The results are compared with the experimental results measured in wave tank.

Response Based Identification of Critical Wave Scenarios

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Günther F. Clauss ◽  
Marco Klein ◽  
Carlos Guedes Soares ◽  
Nuno Fonseca
Keyword(s):  
Linear Method ◽  
Bending Moment ◽  
Extreme Wave ◽  
Offshore Structure ◽  
Sea State ◽  
Worst Case ◽  
Strip Theory ◽  
Wave Conditions ◽  
Vertical Bending Moment ◽  
Method Approach

In the past few years the identification and investigation of critical wave sequences in terms of offshore structure responses became one of the main topics in the ocean engineering community. Thereby the area of interest covers the entire field of application spectra at sea—from efficient and economic offshore operations in moderate sea states to reliability as well as survival in extreme wave conditions. For most cases, the focus lies on limiting criteria for the design, such as maximum global loads, maximum relative motions between two or more vessels, or maximum accelerations, at which the floating structure has to operate or to survive. These criteria are typically combined with a limiting characteristic sea state (Hs, Tp) or a rogue wave. For the investigation of offshore structures as well as the identification of critical wave sequences, different approaches are available—most of them are based on linear transfer functions as it is an efficient procedure for the fast holistic evaluation. But, for some cases the linear method approach implies uncertainties due to nonlinear response behavior, in particular in extreme wave conditions. This paper presents an approach to these challenges, a response based optimization tool for critical wave sequence detection. This tool, which has been successfully introduced for the evaluation of the applicability of a multibody system based on the linear method approach, is adjusted to a nonlinear task—the vertical bending moment of a chemical tanker in extreme wave conditions. Therefore a nonlinear strip theory solver is introduced into the optimization routine to capture the nonlinear effects on the vertical bending moment due to steep waves. The goal of the procedure is to find a worst case wave sequence for a certain critical sea state. This includes intensive numerical investigation as well as model test validation.

Short Term Distribution of Loads Acting on a Cruise Vessel in Extreme Seas Using a Body Nonlinear Time Domain With Second Order Froude-Krylov Pressure

2015 ◽  
Author(s):  
Suresh Rajendran ◽  
Nuno Fonseca ◽  
C. Guedes Soares
Keyword(s):  
Free Surface ◽  
Time Domain ◽  
Surface Condition ◽  
Bending Moment ◽  
The Body ◽  
Short Term ◽  
Weakly Nonlinear ◽  
Strip Theory ◽  
Vertical Bending Moment ◽  
Nonlinear Time Domain

Short term probability distribution of the vertical bending moment acting on a cruise vessel in extreme seas is calculated using a body nonlinear time domain method based on strip theory. The hydrodynamic forces are calculated for the exact wetted surface area under the incident wave profile. The incident potential satisfies the weakly nonlinear free surface condition based on the Stokes expansion. The disturbance potential satisfies the linear free surface and body boundary conditions. Certain practical engineering techniques are employed for the calculation of the body nonlinear forces. The statistics and the probability of distribution of the numerical vertical bending moment are compared with the experimental results measured in the wave tank.

Sign in / Sign up

Export Citation Format

Share Document