Investigation of the Effects of Microgrooved Cutting Tool in High Speed Machining of AISI 1045 Steel

2017 ◽  
Author(s):  
Xingbang Chen ◽  
Nick H. Duong ◽  
J. Ma ◽  
Shuting Lei
Keyword(s):  
Cutting Force ◽  
High Speed ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Contact Length ◽  
High Speed Machining ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
Cutting Inserts ◽  
1045 Steel

In this paper, numerical investigation of the effects of microgroove textured cutting tools in high speed machining of AISI 1045 is conducted using Finite Element Method (FEM). Microgrooves are designed and fabricated on the rake face of cemented carbide (WC/Co) cutting inserts. The effects of microgroove width, edge distance (the distance from cutting edge to the first microgroove), and microgroove depth are examined and assessed in terms of main cutting force, thrust force, and tool-chip contact length. It is found that microgrooved cutting tools generate lower cutting force and consequently lower the energy necessary for machining. This research provides insightful guidance for optimizing tool life and reducing energy consumption in high-speed machining of AISI 1045 steel.

Assessment of the Performance of Microbumped Cutting Tool in Machining of AISI 1045 Steel

2014 ◽  
Author(s):  
J. Ma ◽  
Nick H. Duong ◽  
Shuting Lei
Keyword(s):  
Cutting Force ◽  
Cutting Tool ◽  
Thrust Force ◽  
Cutting Tools ◽  
Contact Length ◽  
Machining Performance ◽  
Edge Distance ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel

This paper investigates the performance of microbump textured cutting tool in dry orthogonal machining of mild steel (AISI 1045 steel) using AdvantEdge finite element simulation. Microbumps are designed on the rake face of cemented carbide (WC/Co) cutting inserts. The purpose is to examine the effect of microbump textured tools on machining performance and to compare it with non-textured regular cutting tools. Specifically, the following microbump parameters are examined: microbump width, microbump height, and edge distance (the distance from cutting edge to the first microbump). Their effects are assessed in terms of the main force, thrust force, and chip-tool contact length. It is found that microbump textured cutting tools generate lower cutting force and thrust force and consequently lower the energy consumption for machining. The micobump width, microbump height, and edge distance all have influence on cutting force in their own ways.

CEL FEM Investigation of Effects of Microgrooved Cutting Tools in High Speed Machining of AISI 1045 Steel

2017 ◽  
Author(s):  
Han Wu ◽  
Nick H. Duong ◽  
J. Ma ◽  
Shuting Lei
Keyword(s):  
Cutting Force ◽  
High Speed ◽  
Cutting Tools ◽  
Cutting Temperature ◽  
Chip Morphology ◽  
High Speed Machining ◽  
Rake Face ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel

In this paper, the commercial FEM software package Abaqus is used to investigate the effects of microgrooved cutting tools in high speed orthogonal cutting of AISI 1045 steel. Microgrooves are designed and fabricated on the rake face of cemented carbide (WC/Co) cutting inserts. A coupled Eulerian-Lagrangian (CEL) finite element model is developed based on Abaqus to solve the evolution of the cutting temperature, chip morphology, cutting force, and phase constitutes simultaneously. This model is validated by comparing the numerical results with the experimental data for orthogonal high speed cutting of AISI 1045 steel with various cutting conditions. In addition, this model is also validated by comparing with the experimental data of regular tool and microgrooved cutting tool under the cutting speed of 120m/min. This validated CEL FEM model is then utilized to investigate the effects of microgrooved cutting tools on the phase transformation, cutting force, cutting temperature, and chip morphology in high speed orthogonal cutting of AISI 1045. The effects of microgroove width, edge distance (the distance from cutting edge to the first microgroove), and microgroove depth are examined and assessed in terms of cutting force, cutting temperature, chip morphology, and phase transformation. It is found that this CEL FEM model can capture the essential features of orthogonal high speed cutting of AISI 1045 using microgrooved cutting tools. It is also concluded that microgrooved cutting tools can not effectively reduce the cutting force in high speed machining, which is contrary to the conclusion obtained for low speed machining in previous research. However, microgrooves on the rake face have influence on the austenite percentage in the chip near the rake face. This research provides insightful guidance for optimizing the cutting performance in terms of cutting temperature, cutting force, chip morphology, and phase transformation in high speed machining of AISI 1045 steel.

Assessment of Restricted Contact Cutting Tool in Dry Machining of AISI 1045 Steel

2014 ◽  
Author(s):  
J. Ma ◽  
Xianchen Ge ◽  
Nick H. Duong ◽  
Shuting Lei
Keyword(s):  
Cutting Force ◽  
Cutting Tool ◽  
Thrust Force ◽  
Alpha Angle ◽  
Cutting Tools ◽  
Rake Face ◽  
Edge Radius ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel

This paper studies the performance of restricted cutting tool in dry orthogonal machining of mild steel (AISI 1045 steel) using finite element simulations. The rake face of cemented carbide (WC/Co) cutting inserts is designed and the rake face length is shortened. The purpose is to examine the effect of shortened tools on machining performance and to compare it with regular cutting tools. The following restricted tool parameters are examined: length of rake face, alpha angle (the angle between the rake face and the supporting face), and edge radius. Their effects are assessed in terms of the main force, thrust force, and chip-tool contact length. It is found that restricted cutting tools generate lower cutting force and thrust force and consequently lower the energy necessary for machining. The length of rake face, the angle between the rake face and the supporting face, and edge radius all have influence on cutting force in their own ways. The effects of these three parameters on the tool temperature distribution are also investigated.

Assessment of Microgrooved Cutting Tool in Dry Machining of AISI 1045 Steel

2015 ◽  
Vol 137 (3) ◽  
Author(s):  
Jianfeng Ma ◽  
Nick H. Duong ◽  
Shing Chang ◽  
Yunsong Lian ◽  
Jianxin Deng ◽  
...  
Keyword(s):  
Cutting Force ◽  
Cutting Tool ◽  
Thrust Force ◽  
Cutting Tools ◽  
Groove Depth ◽  
Groove Width ◽  
Edge Distance ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel

This paper studies the performance of microgrooved cutting tool in dry orthogonal machining of mild steel (AISI 1045 steel) using advantedge finite element simulation. Microgrooves are designed on the rake face of cemented carbide (WC/Co) cutting inserts. The purpose is to examine the effect of microgroove textured tools on machining performance and to compare it with nontextured cutting tools. Specifically, the following groove parameters are examined: groove width, groove depth, and edge distance (the distance from cutting edge to the first groove). Their effects are assessed in terms of the main force, thrust force, and chip–tool contact length. It is found that microgrooved cutting tools generate lower cutting force and thrust force, and consequently lower the energy necessary for machining. The groove width, groove depth, and edge distance all have influence on cutting force in their own ways.

scholarly journals Selection of Machining Parameters Using a Correlative Study of Cutting Tool Wear in High-Speed Turning of AISI 1045 Steel

2018 ◽  
Vol 2 (4) ◽  
pp. 66 ◽  
Author(s):  
Luis Hernández González ◽  
Yassmin Seid Ahmed ◽  
Roberto Pérez Rodríguez ◽  
Patricia Zambrano Robledo ◽  
Martha Guerrero Mata
Keyword(s):  
High Speed ◽  
Manufacturing Industry ◽  
Cutting Tool ◽  
Flank Wear ◽  
Machining Parameters ◽  
High Speed Turning ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel ◽  
Coated Carbide

The manufacturing industry aims to produce many high quality products efficiently at low cost, thereby motivating companies to use advanced manufacturing technologies. The use of high-speed machining is increasingly widespread; however, it lacks a deep-rooted knowledge base needed to facilitate implementation. In this paper, response surface methodology (RSM) has been applied to determine the optimum cutting conditions leading to minimum flank wear in high-speed dry turning on AISI 1045 steel. The mathematical models in terms of machining parameters were developed for flank wear prediction using RSM on the basis of experimental results. The high speed turning experiments were carried out with two coated carbide and a cermet inserts using AISI 1045 steel as work material at different cutting speeds and machining times. The models selected for optimization were validated through the Pareto principle. Results showed the GC4215 insert to be the most optimal option, because it did not reach the cutting tool life limit and could be used for the whole range of cutting parameters selected. To quantitatively evaluate the usefulness of the cutting tools, it was proposed the coefficient of use of the tools from the results of the contour graphs. The GC4215 insert showed 100% effectiveness, followed by the GC4225 with 98.4%, and finally, the CT5015 insert with 83%.

scholarly journals EFFECT OF CUTTING SPEED IN THE TURNING PROCESS OF AISI 1045 STEEL ON CUTTING FORCE AND BUILT-UP EDGE (BUE) CHARACTERISTICS OF CARBIDE CUTTING TOOL

SINERGI ◽  
2020 ◽  
Vol 24 (3) ◽  
pp. 171
Author(s):  
Sobron Yamin Lubis ◽  
Sofyan Djamil ◽  
Yehezkiel Kurniawan Zebua
Keyword(s):  
Cutting Force ◽  
Metal Cutting ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Process ◽  
Depth Of Cut ◽  
Aisi 1045 Steel ◽  
1045 Steel

In the machining of metal cutting, cutting tools are the main things that must be considered. Using improper cutting parameters can cause damage to the cutting tool. The damage is Built-Up Edge (BUE). The situation is undesirable in the metal cutting process because it can interfere with machining, and the surface roughness value of the workpiece becomes higher. This study aimed to determine the effect of cutting speed on BUE that occurred and the cutting strength caused. Five cutting speed variants are used. Observation of the BUE process is done visually, whereas to determine the size of BUE using a digital microscope. If a cutting tool occurs BUE, then the cutting process is stopped, and measurements are made. This study uses variations in cutting speed consisting of cutting speed 141, 142, 148, 157, 163, and 169 m/min, and depth of cut 0.4 mm. From the results of the study were obtained that the biggest feeding force is at cutting speed 141 m/min at 347 N, and the largest cutting force value is 239 N with the dimension of BUE length: 1.56 mm, width: 1.35 mm, high: 0.56mm.

scholarly journals FINITE ELEMENT MODELING OF TEMPERATURE FIELDS ON THE CUTTING EDGE IN THE DRY HIGH-SPEED TURNING OF AISI 1045 STEEL

2020 ◽  
Vol 18 (2) ◽  
pp. 205
Author(s):  
Roberto Pérez ◽  
Luis Hernández ◽  
Ana Quesada ◽  
Julio Pino ◽  
Enrique Zayas
Keyword(s):  
Finite Element ◽  
Temperature Field ◽  
High Speed ◽  
Cutting Tools ◽  
Temperature Fields ◽  
High Speed Turning ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel ◽  
Conventional Machining

High-speed turning is an advanced and emerging machining technique that, in contrast to the conventional machining, allows the manufacture of the workpiece with high accuracy, efficiency and quality, with lower production costs and with a considerable reduction in the machining times. The cutting tools used for the conventional machining cannot be employed for high-speed machining due to a high temperature induced in machining and a lower tool life. Therefore, it is necessary to study the influence of high cutting speeds on the temperature distribution in different typologies of cutting tools, with the aim of evaluating their behavior. In this paper, a finite element method modeling approach with arbitrary Lagrangian-Eulerian fully coupled thermal-stress analysis is employed. The research presents the results of different cutting tools (two coated carbide tools and uncoated cermet) effects on average surface temperature fields on the cutting edge in the dry high-speed turning of AISI 1045 steel. The numerical experiments were designed based on different cutting tools like input parameters and different temperature field zones like dependent variables in the dry high-speed turning of AISI 1045 steel. The results indicate that the dry high-speed turning of AISI 1045 steel does not influence significantly the temperature field zones when P10, P15 or P25 inserts are used. Therefore, the use of a dry high-speed turning method, which reduces the amount of lubricant and increases productivity, may represent an alternative to turning to the extent here described.

Effect on Flow Stress of a Rapid Phase Transition in AISI 1045 Steel

2011 ◽  
Author(s):  
Timothy J. Burns ◽  
Steven P. Mates ◽  
Richard L. Rhorer ◽  
Eric P. Whitenton ◽  
Debasis Basak
Keyword(s):  
Phase Transition ◽  
High Speed ◽  
Compressive Loading ◽  
Kolsky Bar ◽  
High Speed Machining ◽  
Eutectoid Temperature ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel ◽  
Cook Model

New experimental data on AISI 1045 steel from the NIST pulse-heated Kolsky Bar Laboratory are presented. The material is shown to exhibit a nonequilibrium phase transformation at high strain rate. An interesting feature of these data is that the material has a stiffer response to compressive loading when it has been preheated to a testing temperature that is below the eutectoid temperature using pulse-heating than it does when it has been preheated using a slower heating method. On the other hand, when the material has been pulse-heated to a temperature that exceeds the eutectoid temperature prior to compressive loading on the Kolsky bar, it is shown to exhibit a significant loss of strength. A consequence of this behavior is that fixed-parameter constitutive models, such as the well-known Johnson-Cook model, cannot be used to describe this constitutive response behavior. An argument is made that the phase transition does not occur during high-speed machining operations, and suggestions are made as to how to modify the Johnson-Cook model of Jaspers and Dauzenberg for this material in order to obtain improved temperature predictions in finite-element simulations of high-speed machining processes.

Sign in / Sign up

Export Citation Format

Share Document