Numerical Simulation of Nonlinear Flow and Heat Transfer in a Sudden Expansion and Contraction Channel

2016 ◽  
Author(s):  
M. Yang ◽  
L. Q. Yang ◽  
W. Lu ◽  
L. Li ◽  
Q. X. Liu ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Reynolds Number ◽  
Rectangular Channel ◽  
Flow Region ◽  
Nonlinear Flow ◽  
Forced Flow ◽  
Sudden Expansion ◽  
Symmetric State ◽  
Flow And Heat Transfer

Numerical simulation of forced flow in sudden-expansion followed by sudden-contraction rectangular channel was presented for the whole flow region. The nonlinear flow and heat transfer characteristics were investigated by various Reynolds number and geometrical dimension and the critical Reynolds numbers under different conditions have been calculated. The results show flow and heat transfer from symmetric state to asymmetric state with the increase of Re. When Re<Rec (critical Reynolds number for flow transformation), the symmetric state is stable. On the other hand, when Re ≥Rec, the flow loses stability and from symmetric to asymmetric via a symmetry-breaking bifurcation. And the heat transfer performance have relevant characteristics as fluid flow.

scholarly journals Heat transfer and flow region characteristics study in a non-annular channel between rotor and stator

2012 ◽  
Vol 16 (2) ◽  
pp. 593-603 ◽  
Author(s):  
M. Nili-Ahmadabadi ◽  
H. Karrabi
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Flow Characteristics ◽  
Annular Channel ◽  
Flow Region ◽  
Air Gap ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer ◽  
Slip Ring

This paper will present the results of the experimental investigation of heat transfer in a non-annular channel between rotor and stator similar to a real generator. Numerous experiments and numerical studies have examined flow and heat transfer characteristics of a fluid in an annulus with a rotating inner cylinder. In the current study, turbulent flow region and heat transfer characteristics have been studied in the air gap between the rotor and stator of a generator. The test rig has been built in a way which shows a very good agreement with the geometry of a real generator. The boundary condition supplies a non-homogenous heat flux through the passing air channel. The experimental devices and data acquisition method are carefully described in the paper. Surface-mounted thermocouples are located on the both stator and rotor surfaces and one slip ring transfers the collected temperature from rotor to the instrument display. The rotational speed of rotor is fixed at three under: 300rpm, 900 rpm and 1500 rpm. Based on these speeds and hydraulic diameter of the air gap, the Reynolds number has been considered in the range: 4000<Rez<30000. Heat transfer and pressure drop coefficients are deduced from the obtained data based on a theoretical investigation and are expressed as a formula containing effective Reynolds number. To confirm the results, a comparison is presented with Gazley?s (1985) data report. The presented method and established correlations can be applied to other electric machines having similar heat flow characteristics.

Computation of Flow and Heat Transfer in Rotating Rectangular Channels (AR=4:1) With Pin-Fins by a Reynolds Stress Turbulence Model

2006 ◽  
Vol 129 (6) ◽  
pp. 685-696 ◽  
Author(s):  
Guoguang Su ◽  
Hamn-Ching Chen ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Rotation Number ◽  
Rectangular Channel ◽  
Density Ratio ◽  
Three Dimensional ◽  
Diameter Ratio ◽  
Mean Velocity ◽  
Flow And Heat Transfer ◽  
Pin Fins

Computations with multi-block chimera grids were performed to study the three-dimensional turbulent flow and heat transfer in a rotating rectangular channel with staggered arrays of pin-fins. The channel aspect ratio (AR) is 4:1, the pin length to diameter ratio (H∕D) is 2.0, and the pin spacing to diameter ratio is 2.0 in both the stream-wise (S1∕D) and span-wise (S2∕D) directions. A total of six calculations have been performed with various combinations of rotation number, Reynolds number, and coolant-to-wall density ratio. The rotation number and inlet coolant-to-wall density ratio varied from 0.0 to 0.28 and from 0.122 to 0.20, respectively, while the Reynolds number varied from 10,000 to 100,000. For the rotating cases, the rectangular channel was oriented at 150deg with respect to the plane of rotation to be consistent with the configuration of the gas turbine blade. A Reynolds-averaged Navier-Stokes (RANS) method was employed in conjunction with a near-wall second-moment turbulence closure for detailed predictions of mean velocity, mean temperature, and heat transfer coefficient distributions.

DNS of Expansion Ratio Effects on Three-Dimensional Unsteady Separated Flow and Heat Transfer Around a Downward Step

2005 ◽  
Author(s):  
Aya Kito ◽  
Kazuaki Sugawara ◽  
Hiroyuki Yoshikawa ◽  
Terukazu Ota
Keyword(s):  
Heat Transfer ◽  
Rectangular Channel ◽  
Three Dimensional ◽  
Side Wall ◽  
Separated Flow ◽  
Flow Region ◽  
Expansion Ratio ◽  
Mean Velocity ◽  
Flow And Heat Transfer ◽  
Channel Expansion

The direct numerical simulation methodology was employed to analyze the unsteady features of a three-dimensional separated flow and heat transfer around a downward step in a rectangular channel, and to clarify systematically the channel expansion ratio effects upon them. Numerical calculations were carried out using the finite difference method. The Reynolds number Re based on the mean velocity at inlet and the step height was varied from 300 to 1000. The channel expansion ratio ER is 1.5, 2.0 and 3.0 under a step aspect ratio of 36.0. It is found that the flow is steady upto Re = 500 but becomes sensibly unsteady at Re = 700 for all the three expansion ratios. In the case of ER = 2.0, the separated shear layer is most unstable. In the case of ER = 1.5, the longitudinal vortices formed near the side walls of channel are strongest. Nusselt number reaches its maximum in the reattachment flow region and also in the neighborhood of the side wall, and their locations depend greatly upon ER and Re.

DNS of Three-Dimensional Unsteady Separated Flow and Heat Transfer in a Sudden-Expansion Channel

2005 ◽  
Author(s):  
Hiroyuki Yoshikawa ◽  
Kimitake Ishikawa ◽  
Terukazu Ota
Keyword(s):  
Heat Transfer ◽  
Rectangular Channel ◽  
Three Dimensional ◽  
Separated Flow ◽  
Expansion Ratio ◽  
Sudden Expansion ◽  
Number Range ◽  
Simulation Methodology ◽  
Flow And Heat Transfer ◽  
Unsteady Separated Flow

Numerical results of a three-dimensional unsteady separated flow and heat transfer in a sudden expansion rectangular channel are presented. A direct numerical simulation methodology was employed in the calculations using the finite difference method. Treated in the present study is a rectangular channel of aspect ratio AR = 4.0 and expansion ratio ER = 2.5 in a Reynolds number range from 200 to 1000. It is found that the flow becomes unsteady at Re = 400 and severely complicated at Re = 500 to 1000. The heat transfer characteristics are presented and discussed in relation to the flow ones.

Numerical Simulation of Heat and Flow of Liquid Through Minichannels

2006 ◽  
Author(s):  
Heming Yun ◽  
Lin Cheng ◽  
Liqiu Wang ◽  
Shusheng Zhang
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Reynolds Number ◽  
Aspect Ratio ◽  
Flow Region ◽  
Resistance Coefficient ◽  
Equivalent Diameter ◽  
Nusselt Numbers ◽  
Friction Factors ◽  
Simulation Results

In this paper the heat transfer and flow in minichannels was investigated by using CFD methods. The numerical simulation results show that the equivalent diameter has little influence on resistance coefficient in the laminar region. In the turbulent flow region, the resistance coefficient decreases with the increasing of the equivalent diameter. In all computation region, the friction factors increases with increasing of the aspect ratio, and the friction factors decreases obviously with increasing of Reynolds number. The numerical simulation results show that the equivalent diameter has little influence on heat transfer Nusselt number in laminar flow region. In turbulent region, the Nusselt numbers are larger than those in macro channels. The Nusselt numbers increase with decreasing of equivalent diameter and the aspect ratio for a given Reynolds number.

Computation of Flow and Heat Transfer in Rotating Rectangular Channels (AR=4:1) With Pin-Fins by a Reynolds Stress Turbulence Model

2005 ◽  
Author(s):  
Guoguang Su ◽  
Hamn-Ching Chen ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Rotation Number ◽  
Rectangular Channel ◽  
Density Ratio ◽  
Three Dimensional ◽  
Diameter Ratio ◽  
Mean Velocity ◽  
Flow And Heat Transfer ◽  
Pin Fins

Computations with multi-block chimera grids were performed to study the three-dimensional turbulent flow and heat transfer in a rotating rectangular channel with staggered arrays of pin-fins. The channel aspect ratio (AR) is 4:1, the pin length to diameter ratio (H/D) is 2.0, and the pin spacing to diameter ratio is 2.0 in both the stream-wise (S1/D) and span-wise (S2/D) directions. A total of six calculations have been performed with various combinations of rotation number, Reynolds number, and coolant-to-wall density ratio. The rotation number and inlet coolant-to-wall density ratio varied from 0.0 to 0.28 and from 0.122 to 0.20, respectively, while the Reynolds number varied from 10,000 to 100,000. For the rotating cases, the rectangular channel was oriented at 150 deg with respect to the plane of rotation to be consistent with the configuration of the gas turbine blade. A Reynolds-Averaged Navier-Stokes (RANS) method was employed in conjunction with a near-wall second-moment turbulence closure for detailed predictions of mean velocity, mean temperature, and heat transfer coefficient distributions.

Experimental Study on Thermal-Hydraulic Performance of Single-Phase Water Flow in Narrow Rectangular Channel

2009 ◽  
Author(s):  
Mei Wang ◽  
Yan Wen ◽  
Suizheng Qiu ◽  
Guanghui Su ◽  
Weifeng Ni
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Laminar Flow ◽  
Friction Factor ◽  
Water Flow ◽  
Single Phase ◽  
Rectangular Channel ◽  
Flow Region ◽  
Phase Water

The purpose of this study is to discover the differences of pressure drop and heat transfer of single-phase water flow between conventional channels and narrow rectangular channels. Furthermore, the differences between the level and the vertical channel have been studied. The gap of the test channel is 1.8mm. Compared with conventional channels, the narrow rectangular channel showed differences in both flow and heat transfer characteristics. The critical Reynolds number of transition from laminar flow to turbulent flow is 900∼1300, which is smaller compared with conventional channels. The friction factor is larger than that of the conventional channels and the correlation of friction factor with Reynolds number was given by experimental results. From the relation graph of Nusselt number and Reynolds number, the demarcation of the laminar flow region and turbulence flow region is obvious. In laminar region, Nusselt number almost remained constant and approximately consistent with numerical simulation results. While in turbulent region, Nusselt number increased significantly with increasing Reynolds number. A new Nusselt number correlation was obtained based on Dittus-Boelter equation, and the coefficients were less about 13% than that of Dittus-Boelter equation.

Sign in / Sign up

Export Citation Format

Share Document