Neutron Diffraction Studies of Residual Stresses Around Gouges and Gouged Dents

2012 ◽  
Author(s):  
Lynann Clapham ◽  
Vijay Babbar ◽  
Thomas Gnaeupel-Herold ◽  
Remi Batisse ◽  
Mures Zarea
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Neutron Diffraction ◽  
Stress Field ◽  
Residual Stresses ◽  
Wall Stress ◽  
Outer Wall ◽  
Stress Distributions ◽  
Wall Surface ◽  
Residual Stress Field

The residual stress pattern surrounding gouges is complex and, to date, has not been accurately modeled using stress modeling software. Thus measurement of these stress distributions is necessary. Neutron diffraction is the only experimental method with the capability of directly evaluating residual strain throughout the entire thickness of a pipe wall, in and around dent or gouged regions. Neutron diffraction measurements were conducted at the NIST reactor on three gouged dents in X52 pipeline sections. These were part of a larger sample set examined as part of the comprehensive MD4-1 PRCI/DOT PHMSA project. Gouges contained in pipeline sections were termed BEA161 (primarily a gouge with little denting), and BEA178 (mild gouging, very large dent). Measurements were also conducted on a coupon sample – P22, that was created as part of an earlier study. For the moderate gouges with little or no associated denting (BEA161 and P22) the residual stress field was highly localized around the immediate gouge vicinity (except where there was some denting present). The through wall stress distributions were similar at most locations — characterized by neutral or moderate hoop and axial stresses (50–100MPa) at the outer wall surface (i.e. at the gouge itself) gradually becoming highly compressive (up to −600MPa) at the inner wall surface. The other sample (BEA178) exhibited a very mild gouge with significant denting, and the results were very different. The denting process associated with this kind of gouge+dent dominated the residual stresses, making the residual stress distribution very complex. In addition, rather than having a residual stress field that is localized in the immediate gouge vicinity, the varying stress distribution extends to the edge of the dented region..

The Effect of Residual Stresses on the Fracture Resistance of Ductile Steels

2002 ◽  
Author(s):  
Noel P. O’Dowd ◽  
Yuebao Lei
Keyword(s):  
Residual Stress ◽  
Stress Field ◽  
Residual Stresses ◽  
Crack Opening ◽  
Stress Distributions ◽  
Residual Stress Field ◽  
Element Analysis ◽  
Fatigue And Fracture ◽  
Negative Effect ◽  
Fracture Performance

Tensile residual stresses, such as those generated by welding, act as crack opening stresses and can have a negative effect on the fatigue and fracture performance of a component. In this work the effect of representative residual stress distributions on the fracture behaviour of a ferritic steel has been examined using finite element analysis. A Gurson-type void growth model is used to model the effect of ductile tearing ahead of a crack. For the cases examined it is seen that a tensile residual stress field may lead to a reduction in the toughness of the material (as represented by the J-resistance curve). The observed difference in toughness can be linked to the different constraint levels in the specimens due to the introduction of the residual stress field and can be rationalised through the use of a two parameter, J–Q approach.

Abrasive Waterjet Peening With Elastic Prestress: Subsurface Residual Stress Distribution

2007 ◽  
Author(s):  
Balaji Sadasivam ◽  
Alpay Hizal ◽  
Dwayne Arola
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Stress Field ◽  
Yield Strength ◽  
Residual Stresses ◽  
Residual Stress Distribution ◽  
Abrasive Waterjet ◽  
Residual Stress Field ◽  
Surface Residual Stress ◽  
Compressive Residual Stresses

Recent advances in abrasive waterjet (AWJ) technology have resulted in new processes for surface treatment that are capable of introducing compressive residual stresses with simultaneous changes in the surface texture. While the surface residual stress resulting from AWJ peening has been examined, the subsurface residual stress field resulting from this process has not been evaluated. In the present investigation, the subsurface residual stress distribution resulting from AWJ peening of Ti6Al4V and ASTM A228 steel were studied. Treatments were conducted with the targets subjected to an elastic prestress ranging from 0 to 75% of the substrate yield strength. The surface residual stress ranged from 680 to 1487 MPa for Ti6Al4V and 720 to 1554 MPa for ASTM A228 steel; the depth ranged from 265 to 370 μm for Ti6Al4V and 550 to 680 μm for ASTM A228 steel. Results showed that elastic prestress may be used to increase the surface residual stress in AWJ peened components by up to 100%.

An evaluation of residual stress distribution in welded compact tension specimens using neutron diffraction

2005 ◽  
Vol 40 (2) ◽  
pp. 211-216 ◽  
Author(s):  
G. O Rading
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Neutron Diffraction ◽  
Stress Field ◽  
Fatigue Cracks ◽  
Compact Tension ◽  
Maximum Tensile Stress ◽  
Thickness Variation ◽  
Residual Stress Field ◽  
Neutron Diffraction Technique

The neutron diffraction technique was used to determine the residual stress field in welded compact tension specimens of the aluminium-lithium alloy AA 2095. The deep penetrating characteristic of neutrons was exploited to evaluate the through-thickness variation in residual stress. Moreover, insight into the redistribution of these stresses was gained by extending a fatigue crack through the residual stress field and re-examining the stress distribution. The specimen without a crack was found to have a high compressive stress (of the order of - 135MPa) ahead of the notch. This rose to a maximum tensile stress of about 50MPa, 22 mm from the notch, followed by a drop to negative values further ahead of the notch. It was observed that the magnitude of the stresses changed on moving into the thickness of the specimen. However, the form of the graph showing stress versus distance ahead of the notch remained unchanged. When fatigue cracks of different lengths were introduced, the magnitude of the stress close to the tip first increased with crack length, before decreasing and then rising again. Nevertheless, the form of the graph remained unchanged and the stress at the crack tip remained compressive. The paper concludes that any study of the response of a component to mechanical loading involving a residual stress field must take these factors (i.e. through-thickness stress variation and stress redistribution) into consideration.

Standardized Through-Wall Distributions of Dissimilar Metal Weld Residual Stress

2015 ◽  
Author(s):  
John E. Broussard
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Crack Growth ◽  
Welding Process ◽  
Wall Stress ◽  
Residual Stress Distribution ◽  
Analytical Models ◽  
Stress Distributions ◽  
Dissimilar Metal

The residual stresses imparted by the welding process are a principal factor in the process of primary water stress corrosion cracking (PWSCC) of Alloy 82/182 nickel-alloy (i.e., dissimilar metal or DM) piping butt welds in PWRs. While Section XI of the ASME Code requires that residual stresses are considered in crack growth calculations, there is little guidance or requirement on how to calculate them. Analytical models are frequently used to simulate the welding process in order to predict the residual stress distribution in the weld and base material as an input to crack growth calculations. The crack growth calculations, in turn, have demonstrated a high sensitivity to the welding residual stress distribution inputs. While significant progress has been made in understanding and reducing the variability in calculated residual stress among modelers as well as the variability in measured residual stress among different techniques, there remains some uncertainty regarding any given measured or calculated distribution. A feasible alternative to calculating through-wall stress distributions with analytical models on a case-by-case basis is to develop a set of standardized through-wall stress distributions that are applicable to DM welds. Examples of standardized through-wall distributions for residual stress are found in numerous consensus code and standards. The benefit of established through-wall stress distributions is that evaluations for flaws in welds would start from a uniform basis on one of the key inputs to the crack growth calculation, reducing the time required to perform and review flaw evaluations. This paper presents and describes the technical basis for a set of through-wall distributions for common DM welds found in the US nuclear industry. The basis of the distributions include the results of analytical models, including uncertainty, as well as measured data for through-wall stress in DM welds.

scholarly journals Residual stresses in thermite welded rails: significance of additional forging

2020 ◽  
Vol 64 (7) ◽  
pp. 1195-1212
Author(s):  
B. Lennart Josefson ◽  
R. Bisschop ◽  
M. Messaadi ◽  
J. Hantusch
Keyword(s):  
Residual Stress ◽  
Stress Field ◽  
Residual Stresses ◽  
Weld Metal ◽  
Welding Process ◽  
Surface Zone ◽  
Fe Model ◽  
Uneven Surface ◽  
Residual Stress Field ◽  
High Dynamic

Abstract The aluminothermic welding (ATW) process is the most commonly used welding process for welding rails (track) in the field. The large amount of weld metal added in the ATW process may result in a wide uneven surface zone on the rail head, which may, in rare cases, lead to irregularities in wear and plastic deformation due to high dynamic wheel-rail forces as wheels pass. The present paper studies the introduction of additional forging to the ATW process, intended to reduce the width of the zone affected by the heat input, while not creating a more detrimental residual stress field. Simulations using a novel thermo-mechanical FE model of the ATW process show that addition of a forging pressure leads to a somewhat smaller width of the zone affected by heat. This is also found in a metallurgical examination, showing that this zone (weld metal and heat-affected zone) is fully pearlitic. Only marginal differences are found in the residual stress field when additional forging is applied. In both cases, large tensile residual stresses are found in the rail web at the weld. Additional forging may increase the risk of hot cracking due to an increase in plastic strains within the welded area.

The Effects of Loadings on Welding Residual Stresses and Assessment of Fracture Parameters in a Welding Residual Stress Field

2011 ◽  
Author(s):  
Liwu Wei ◽  
Weijing He ◽  
Simon Smith
Keyword(s):  
Residual Stress ◽  
Stress Field ◽  
Residual Stresses ◽  
Path Dependence ◽  
Welding Residual Stress ◽  
Assessment Procedure ◽  
Fe Model ◽  
J Integral ◽  
Residual Stress Field ◽  
Growing Crack

The level of welding residual stress is an important consideration in the ECA of a structure or component such as a pipeline girth weld. Such a consideration is further complicated by their variation under load and the complexity involved in the proper assessment of fracture mechanics parameters in a welding residual stress field. In this work, 2D axi-symmetric FEA models for simulation of welding residual stresses in pipe girth welds were first developed. The modelling method was validated using experimental measurements from a 19-pass girth weld. The modeling method was used on a 3-pass pipe girth weld to predict the residual stresses and variation under various static and fatigue loadings. The predicted relaxation in welding residual stress is compared to the solutions recommended in the defect assessment procedure BS 7910. Fully circumferential internal cracks of different sizes were introduced into the FE model of the three-pass girth weld. Two methods were used to introduce a crack. In one method the crack was introduced instantaneously and the other method introduced the crack progressively. Physically, the instantaneously introduced crack represents a crack originated from manufacturing or fabrication processes, while the progressively growing crack simulates a fatigue crack induced during service. The J-integral values for the various cracks in the welding residual stress field were assessed and compared. This analysis was conducted for a welding residual stress field as a result of a welding simulation rather than for a residual stress field due to a prescribed temperature distribution as considered by the majority of previous investigations. The validation with the 19-pass welded pipe demonstrated that the welding residual stress in a pipe girth weld can be predicted reasonably well. The relaxation and redistribution of welding residual stresses in the three-pass weld were found to be significantly affected by the magnitude of applied loads and the strain hardening models. The number of cycles in fatigue loading was shown to have little effect on relaxation of residual stresses, but the range and maximum load together governed the relaxation effect. A significant reduction in residual stresses was induced after first cycle but subsequent cycles had no marked effect. The method of introducing a crack in a FE model, progressively or instantaneously, has a significant effect on J-integral, with a lower value of J obtained for a progressively growing crack. The path-dependence of the J-integral in a welding residual stress field is discussed.

A Numerical Study on the Redistribution of Residual Stress After Machining

2017 ◽  
Author(s):  
Kunyang Lin ◽  
Wenhu Wang ◽  
Ruisong Jiang ◽  
Yifeng Xiong
Keyword(s):  
Residual Stress ◽  
Stress Field ◽  
Residual Stresses ◽  
Numerical Study ◽  
Cutting Speed ◽  
Machining Process ◽  
Stress Profile ◽  
Residual Stress Field ◽  
Machining Processes ◽  
Residual Stress Profile

Machining induced residual stresses have an important effect on the surface integrity. Effects of various factors on the distribution of residual stress profiles induced by different machining processes have been investigated by many researchers. However, the initial residual, as one of the important factor that affect the residual stress profile, is always been ignored. In this paper, the residual stress field induced by the quenching process is simulated by the FEM software as the initial condition. Then the initial residual stress field is used to study the residual stress redistribution after the machining process. The influence of initial stress on the stress formation is carried out illustrating with the mechanical and thermal loads during machining processes. The effects of cutting speed on the distribution of residual stress profile are also discussed. These results are helpful to understand how initial residual stresses are redistributed during machining better. Furthermore, the results in the numerical study can be used to explain the machining distortion problem caused by residual stress in the further work.

ENPOWER: Investigations by Neutron Diffraction and Finite Element Analyses on Residual Stress Formation in Repair Welds Applied to Ferritic Steel Plates

2005 ◽  
Author(s):  
Carsten Ohms ◽  
Robert C. Wimpory ◽  
Dimitar Neov ◽  
Didier Lawrjaniec ◽  
Anastasius G. Youtsos
Keyword(s):  
Experimental Data ◽  
Residual Stress ◽  
Numerical Analysis ◽  
Neutron Diffraction ◽  
Stress Field ◽  
Ferritic Steel ◽  
Maximum Stress ◽  
Steel Plates ◽  
Residual Stress Field ◽  
Welding Procedure

The European collaborative research project ENPOWER (Management of Nuclear Plant Operation by Optimizing Weld Repairs) has as one of its main objectives the development of guidelines for the application of repair welds to safety critical components in nuclear power plants. In this context letter box repair welds applied to thin ferritic steel plates to simulate repair of postulated shallow cracks have been manufactured for the purpose of experimental and numerical analysis of welding residual stresses. Two specimens have been procured, one of them prepared in accordance with a standard welding procedure, while in the second case a different procedure was followed in order to obtain extended martensite formation in the heat affected zone. Residual stresses have been determined in both specimens by neutron diffraction at the High Flux Reactor of the Joint Research Centre in Petten, The Netherlands. In parallel Institut de Soudure in France has performed a full 3-d analysis of the residual stress field for the standard welding case taking into account the materials and phase transformations. The experimental data obtained for both specimens clearly suggest that the non-conventional welding procedure rendered higher maximum stress values. In the case of the standard welding procedure numerical and experimental data show a reasonable qualitative agreement. The maximum stress value was in both cases found in the same region of the material — in the base metal just underneath the weld pool — and in both cases found to be of similar magnitude (∼800 MPa found in neutron diffraction and ∼700 MPa found in numerical analysis). In this paper the experimental and numerical approaches are outlined and the obtained results are presented. In addition an outlook is given to future work to be performed on this part of the ENPOWER project. A main issue pending is the application of an optimized advanced post weld heat treatment in one of the two cases and the subsequent numerical and experimental determination of its impact on the residual stress field. At the same time further evaluation of the materials transformations due to welding is pursued.

Determination of the Residual Stress Field around Scratches Using Synchrotron X-Rays and Nanoindentation

2010 ◽  
Vol 652 ◽  
pp. 25-30
Author(s):  
M.K. Khan ◽  
Michael E. Fitzpatrick ◽  
L.E. Edwards ◽  
S.V. Hainsworth
Keyword(s):  
Residual Stress ◽  
Stress Field ◽  
Residual Stresses ◽  
Small Scale ◽  
X Rays ◽  
X Ray Diffraction ◽  
Residual Stress Field ◽  
Fine Grained ◽  
Load Displacement

The residual strain field around the scratches of 125µm depth and 5µm root radius have been measured from the Synchrotron X-ray diffraction. Scratches were produced using different tools in fine-grained aluminium alloy AA 5091. Residual stresses up to +1700 micro-strains were measured at the scratch tip for one tool but remained up to only +1000 micro-strains for the other tool scratch. The load-displacement curves obtained from nanoindentation were used to determine the residual stresses around the scratches. It was found that the load-displacement curves are sensitive to any local residual stress field present and behave according to the type of residual stresses. This combination of nanoindentation and synchrotron X-rays has been proved highly effective for the study of small-scale residual stresses around the features such as scratches.

Sign in / Sign up

Export Citation Format

Share Document