Crack Growth Model of Pipeline Steels in Near-Neutral pH Soil Environments

2008 ◽  
Author(s):  
Weixing Chen ◽  
R. Kania ◽  
R. Worthingham ◽  
S. Kariyawasam
Keyword(s):  
Stress Intensity Factor ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Crack Growth ◽  
Growth Model ◽  
Full Scale ◽  
Loading Frequency ◽  
Pipeline Steels ◽  
Neutral Ph ◽  
Full Scale Tests

This paper reports the crack growth behavior of pipeline steels in near-neutral pH environments. Crack growth data both from laboratory tests using compact tension (CT) specimen and from full scale tests of shallow cracks were analyzed using a true corrosion-fatigue model established recently. It has been found that the crack growth rate can be correlated with ΔK2Kmax/fα, where ΔK is the stress intensity factor range; Kmax is the maximum stress intensity factor; f is the loading frequency; and α is a factor related to corrosivity of soil environments. This correlation enables determination of threshold ΔK2Kmax/fα values for long cracks such as in a test using CT specimen. The above growth correlation appears also true for small/shallow cracks in full scale tests except that small/shallow cracks were found to grow at appreciable rates below the threshold of long/deep cracks. Implications of the growth model to crack growth occurring in the field and pipe integrity management were also discussed in the paper.

Hydrogen Assisted Fatigue Crack Growth in a Precipitation-Hardened Martensitic Stainless Steel Under Gaseous Hydrogen

2014 ◽  
Author(s):  
Giovambattista Bilotta ◽  
Mandana Arzaghi ◽  
Gilbert Hénaff ◽  
Guillaume Benoit ◽  
Clara Moriconi ◽  
...  
Keyword(s):  
Stress Intensity Factor ◽  
Fatigue Crack ◽  
Stress Intensity ◽  
Fatigue Crack Growth ◽  
Intensity Factor ◽  
Crack Growth ◽  
Martensitic Stainless Steel ◽  
Gaseous Hydrogen ◽  
Crack Growth Behavior ◽  
Loading Frequency

In this study, the effect of gaseous hydrogen on the fatigue crack growth behavior in a precipitation-hardened martensitic stainless steel is investigated. It is known that the degradation in fatigue crack growth behavior derives from a complex interaction between the fatigue damage and the amount of hydrogen enriching the crack tip, which is dependent on the hydrogen pressure, loading frequency, and stress intensity factor amplitude. Therefore, fatigue crack growth tests were performed in a range of 0.09 to 40 MPa under gaseous hydrogen at a frequency of 20 and 0.2 Hz. The fatigue data as well as fracture morphologies obtained so far indicate a sharp increase in crack growth rates in a narrow range of stress intensity factor amplitudes. Also, it is shown that by decreasing the loading frequency to 0.2 Hz at a given pressure of hydrogen the transition occurs at lower values of stress intensity factor amplitudes accompanied by a change in fracture mode. Scanning electron microscope (SEM) observations of the fracture surfaces are used to support the explanations proposed to account for the observed phenomena.

Influence of Mean Stress Intensity on Fatigue Crack Growth in an Aluminium Alloy

1975 ◽  
Vol 17 (4) ◽  
pp. 199-205 ◽  
Author(s):  
C. M. Branco ◽  
J. C. Radon ◽  
L. E. Culver
Keyword(s):  
Stress Intensity Factor ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Crack Propagation ◽  
Crack Growth ◽  
Threshold Value ◽  
Al Alloy ◽  
Loading Frequency ◽  
Mean Stress ◽  
Mean Values

The effects of the mean stress-intensity factor, Km, and the range of the stress intensity, Δ K, on crack propagation phenomena in the Al-alloy RR 58 have been studied using contoured double-cantilever beam specimens providing a constant stress-intensity factor for all crack lengths. Based on the experimental data available, a relationship of the following form, between the cyclic crack growth rate, d a/d N, and the tensile loading levels, has been proposed: where Δ K = ( Kmax - Kmin); Kmax, Kmin and Km are the maximum, minimum and mean values of the stress-intensity factor; Δ Kth is the threshold value of Δ K for crack propagation; K1C is the critical fracture toughness in plane strain conditions; A and α arc constants. In tests at room temperature (21 °C) in laboratory air and at a loading frequency of 0.15 Hz, it was found that Δ Kth decreased with increasing values of K m, α was equal to 1.36 and A equalled 3.16 times 10-5(in/cycle).

Crack Growth in Stainless Steel 304 under Creep-Fatigue Loading

2007 ◽  
Vol 353-358 ◽  
pp. 485-490 ◽  
Author(s):  
Y.M. Baik ◽  
K.S. Kim
Keyword(s):  
Stress Intensity Factor ◽  
Stainless Steel ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Crack Growth ◽  
Growth Rates ◽  
Static Loading ◽  
Fatigue Loading ◽  
Creep Fatigue ◽  
Crack Growth Rates

Crack growth in compact specimens of type 304 stainless steel is studied at 538oC. Loading conditions include pure fatigue loading, static loading and fatigue loading with hold time. Crack growth rates are correlated with the stress intensity factor. A finite element analysis is performed to understand the crack tip field under creep-fatigue loading. It is found that fatigue loading interrupts stress relaxation around the crack tip and cause stress reinstatement, thereby accelerating crack growth compared with pure static loading. An effort is made to model crack growth rates under combined influence of creep and fatigue loading. The correlation with the stress intensity factor is found better when da/dt is used instead of da/dN. Both the linear summation rule and the dominant damage rule overestimate crack growth rates under creep-fatigue loading. A model is proposed to better correlate crack growth rates under creep-fatigue loading: 1 c f da da da dt dt dt Ψ −Ψ     =         , where Ψ is an exponent determined from damage under pure fatigue loading and pure creep loading. This model correlates crack growth rates for relatively small loads and low stress intensity factors. However, correlation becomes poor as the crack growth rate becomes large under a high level of load.

Slow Crack Growth in Glasses and Ceramics Under Residual and Applied Stresses

1989 ◽  
Vol 111 (1) ◽  
pp. 61-67 ◽  
Author(s):  
F. Erdogan
Keyword(s):  
Stress Intensity Factor ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Residual Stresses ◽  
Crack Growth ◽  
Slow Crack Growth ◽  
Threshold Value ◽  
Crack Arrest ◽  
Growing Crack ◽  
Applied Stresses

The problem of slow crack growth under residual stresses and externally applied loads in plates is considered. Even though the technique developed to treat the problem is quite general, in the solution given it is assumed that the plate contains a surface crack and the residual stresses are compressive near and at the surfaces and tensile in the interior. The crack would start growing subcritically when the stress intensity factor exceeds a threshold value. Initially the crack faces near the plate surface would remain closed. A crack-contact problem would, therefore, have to be solved to calculate the stress intensity factor. Depending on the relative magnitudes of the residual and applied stresses and the threshold and critical stress intensity factors, the subcritically growing crack would either be arrested or become unstable. The problem is solved and examples showing the time to crack arrest or failure are discussed.

Effect of Temperature on Fatigue Crack Growth in CPVC

2003 ◽  
Vol 125 (1) ◽  
pp. 71-77 ◽  
Author(s):  
Muhammad Irfan-ul-Haq ◽  
Nesar Merah
Keyword(s):  
Stress Intensity Factor ◽  
Fatigue Crack ◽  
Stress Intensity ◽  
Fatigue Crack Growth ◽  
Intensity Factor ◽  
Crack Growth ◽  
Effect Of Temperature ◽  
Stress Intensity Factor Range ◽  
Crack Growth Behavior ◽  
Different Temperatures

This study addresses the effect of temperature on fatigue crack growth (FCG) behavior of CPVC. FCG tests were conducted on CPVC SEN tensile specimens in the temperature range −10 to 70°C. These specimens were prepared from 4-in. injection-molded pipe fittings. Crack growth behavior was studied using LEFM concepts. The stress intensity factor was modified to include the crack closure and plastic zone effects. The effective stress intensity factor range ΔKeff gave satisfactory correlation of crack growth rate (da/dN) at all temperatures of interest. The crack growth resistance was found to decrease with temperature increase. The effect of temperature on da/dN was investigated by considering the variation of mechanical properties with temperature. Master curves were developed by normalizing ΔKeff by fracture strain and yield stress. All the da/dN-ΔK curves at different temperatures were collapsed on a single curve. Crazing was found to be the dominant fatigue mechanism, especially at high temperature, while shear yielding was the dominant mechanism at low temperatures.

Mechanisms of Fatigue Crack Growth in WC-Co Cemented Carbides

2005 ◽  
Vol 297-300 ◽  
pp. 1120-1125 ◽  
Author(s):  
Myung Hwan Boo ◽  
Chi Yong Park
Keyword(s):  
Growth Rate ◽  
Stress Intensity Factor ◽  
Fatigue Crack ◽  
Stress Intensity ◽  
Fatigue Crack Growth ◽  
Intensity Factor ◽  
Crack Growth ◽  
Stress Ratio ◽  
Cemented Carbides ◽  
Stress Intensity Factor Range

In order to study the influence of stress ratio and WC grain size, the characteristics of fatigue crack growth were investigated in WC-Co cemented carbides with two different grain sizes of 3 and 6 µm. Fatigue crack growth tests were carried out over a wide range of fatigue crack growth rates covering the threshold stress intensity factor range DKth. It was found that crack growth rate da/dN against stress intensity factor range DK depended on stress ratio R. The crack growth rate plotted in terms of effective stress intensity factor range DKeff still exhibited the effect of microstructure. Fractographic examination revealed brittle fracture at R=0.1 and ductile fracture at R=0.5 in Co binder phase. The amount of Co phase transformation for stress ratio was closely related to fatigue crack growth characteristics.

Sign in / Sign up

Export Citation Format

Share Document