Cut Point Optimization of Diesel Oil: Gasoline Interfaces

2008 ◽  
Author(s):  
Sergio D. Gavi´n
Keyword(s):  
Diesel Oil ◽  
Technical Solution ◽  
Cut Point ◽  
Product Generation ◽  
Pipeline Systems

This paper presents the technical solution developed by Repsol YPF in one of its pipeline systems to reduce contaminated product generation as a result of the interfaces that are generated between diesel oil and gasolines during transport.

Drying and heating of scrap metal at steelmaking: industrial safety, economics, ecology

2020 ◽  
Vol 76 (12) ◽  
pp. 1353-1258
Author(s):  
V. A. Spirin ◽  
V. E. Nikol’skii ◽  
D. V. Vokhmintsev ◽  
A. A. Moiseev ◽  
P. G. Smirnov ◽  
...  
Keyword(s):  
Energy Efficiency ◽  
High Efficiency ◽  
Steel Production ◽  
Scrap Metal ◽  
Industrial Safety ◽  
Technical Solution ◽  
Metal Charge ◽  
Basic Task ◽  
Scrap Heating ◽  
Winter Time

At steel production based on scrap metal utilization, the scrap heating before charging into a melting facility is an important way of energy efficiency increase and ecological parameters improving. In winter time scrap metal charging with ice inclusions into a metal melt can result in a considerable damage of equipment and even accidents. Therefore, scrap preliminary drying is necessary to provide industrial safety. It was shown, that in countries with warm and low-snow climate with no risk of scrap metal icing up during its transportation and storing in the open air, the basic task being solved at the scrap drying is an increase of energy efficiency of steelmaking. InRussiathe scrap metal drying first of all provides the safety of the process and next - energy saving. Existing technologies of scrap metal drying and heating considered, as well as advantages and drawbacks of technical solutions used at Russian steel plants. In winter time during scrap metal heating at conveyers (Consteel process) hot gases penetrate not effectively into its mass, the heat is not enough for evaporation of wetness in the metal charge. At scrap heating by the furnace gases, a problem of dioxines emissions elimination arises. Application of shaft heaters results in high efficiency of scrap heating. However, under conditions of Russian winter the upper scrap layers are not always heated higher 0 °С and after getting into a furnace bath the upper scrap layers cause periodical vapor explosions. The shaft heaters create optimal conditions for dioxines formation, which emit into atmosphere. It was shown, that accounting Russian economic and nature conditions, the metal charge drying and heating in modified charging buckets by the heat of burnt natural gas or other additional fuel is optimal. The proposed technical solution enables to burnt off organic impurities ecologically safely, to melt down ice, to evaporate the wetness in the scrap as well as to heat the charge as enough as the charging logistics enables it. The method was implemented at several Russian steel plants. Technical and economical indices of scrap metal drying in buckets under conditions of EAF-based shop, containing two furnaces ДСП-100, presented.

Technical Solution for Scutching the Raw Bast Material

2018 ◽  
Vol 14 (1) ◽  
pp. 24-35
Author(s):  
Yu.V. Berezovsky ◽  
Keyword(s):  
Technical Solution

MODELING OF THE DYNAMIC PROCESS RELEASE OF STUCK DRILLING TOOLS BY HYDRO-PULSE METHOD

2019 ◽  
pp. 94-103
Author(s):  
K. H. Levchyk ◽  
M. V. Shcherbyna
Keyword(s):  
Mathematical Model ◽  
Dynamic Process ◽  
Drilling Fluid ◽  
Pulse Method ◽  
Geometrical Parameters ◽  
Technical Solution ◽  
Rock Layer ◽  
Drilling Tool ◽  
Drilling Tools ◽  
Drill Pipes

A technical solution is proposed for the elimination the grabbing of drilling tool, based on the use of energy due to the circulation of the drilling fluid. The expediency eliminating the grabbing drilling tool using the hydro-impulse method is substantiated. A method of drawing up a mathematical model for the dynamic process of a grabbing string of drill pipes in the case of perturbation of hydro-impulse oscillations in the area of the productive rock layer is developed. The law of longitudinal displacements arising in the trapped string is obtained, which allows choosing the optimal geometrical parameters of the passage channels and the frequency rotational of shutter for these channels. Recommendations for using this method for practical use have been systematized.

PRESSURE CONTROL SYSTEM AT CEMENTATION OF WELLS

2017 ◽  
pp. 62-67
Author(s):  
V. G. Kuznetsov ◽  
O. A. Makarov
Keyword(s):  
Control System ◽  
Oil And Gas ◽  
Pressure Control ◽  
Poor Quality ◽  
Technical Solution ◽  
Cement Slurry ◽  
Automated Control ◽  
Injection Speed ◽  
Pressure Control System ◽  
Effective Life

At cementing of casing of oil and gas wells during the process of injecting of cement slurry in the casing column the slurry can move with a higher speed than it’s linear injection speed. A break of continuity of fluid flow occurs, what can lead to poor quality isolation of producing formations and shorten the effective life of the well. We need to find some technical solution to stabilize the linear velocity of the cement slurry in the column. This task can be resolved with an automated control system.

Sign in / Sign up

Export Citation Format

Share Document