Non-Intrusive Case Temperature Measurement Method of Direct-Water-Cooled Power Module

2015 ◽  
Author(s):  
Keisuke Horiuchi ◽  
Yuichiro Konishi ◽  
Atsuo Nishihara
Keyword(s):  
Thermal Resistance ◽  
Structure Function ◽  
Temperature Measurement ◽  
Flow Rate ◽  
Measurement Method ◽  
Water Flow Rate ◽  
Power Module ◽  
Thermal Capacitance ◽  
Simulation Results ◽  
Heat Spreading

In this paper, we present a non-intrusive case temperature measurement method of the direct-water-cooled power module. It uses the structure function, which in this case comprises the cumulative thermal capacitance and the cumulative thermal resistance. Since the effective heat transfer rate of the pinfin heatsink varies with the water flow rate, in this study we assumed the inflection point of the structure function corresponding to the change in the flow rate was junction-case thermal resistance. We compared numerical simulation results with experimental results and present our findings. Finally, we show that the design area in which the heat spreading angle of 45 degrees, the well-known rule of thumb, is suitable.

Thermal Performance Comparison for Five Liquid Heat Sink Designs

2011 ◽  
Author(s):  
Christopher Greene ◽  
Randall D. Manteufel ◽  
Amir Karimi
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Thermal Resistance ◽  
Flow Rate ◽  
Heat Sink ◽  
Fluid Velocity ◽  
Water Flow Rate ◽  
High Flow ◽  
Heat Transfer Area ◽  
Flow Rates

Five high-flow liquid-cooled heat sink designs are compared for the cooling of a single chip CPU. Five distinctive design configurations are considered with regard to the introduction, passage, and extraction of cooling fluid. The typical water flow rate is about 3.8 liters per minute (lpm) with flow passages in the primary heat transfer area ranging from 2 to 0.1mm. The design configurations are summarized and compared, considering: the primary convective heat transfer area, flow passage streamlining, acceleration mechanisms, and nominal fluid velocity in the primary heat transfer area. Overall pressure drop and thermal resistance are compared for varying flow rates of water. At the nominal flow, the pressure drops ranged from 1 kPa to 20 kPa. In the restrictive designs, such as nozzles, flow acceleration accounts for the largest source of pressure drop. In some designs, a large fraction of the overall pressure drop is due to circuitous flow associated with the introduction and/or extraction of flow which contributes little to heat removal. At the nominal flow, the overall thermal resistance varied from 0.14 to 0.18 C/W. As flow rate increases the overall thermal resistance decreases. Results indicated that 80 to 85% of the total thermal resistance is due to conduction and about 15 to 20% attributed to convection at the nominal flow rate. There is minimal thermal benefit for flow rates beyond twice the nominal while this substantially increases fluid pumping requirements. This study highlights design features which yield above average heat transfer performance with minimal pressure drop for high-flow liquid-cooled heat sinks.

scholarly journals Effect of Water Flow on Underwater Wet Welded A36 Steel

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 682
Author(s):  
Eko Surojo ◽  
Aziz Harya Gumilang ◽  
Triyono Triyono ◽  
Aditya Rio Prabowo ◽  
Eko Prasetya Budiana ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Flow ◽  
Flow Rate ◽  
Water Flow Rate ◽  
Physical And Mechanical Properties ◽  
Shielded Metal Arc Welding ◽  
Effect Of Water ◽  
Bending Effect ◽  
Metal Arc Welding ◽  
A36 Steel

Underwater wet welding (UWW) combined with the shielded metal arc welding (SMAW) method has proven to be an effective way of permanently joining metals that can be performed in water. This research was conducted to determine the effect of water flow rate on the physical and mechanical properties (tensile, hardness, toughness, and bending effect) of underwater welded bead on A36 steel plate. The control variables used were a welding speed of 4 mm/s, a current of 120 A, electrode E7018 with a diameter of 4 mm, and freshwater. The results show that variations in water flow affected defects, microstructure, and mechanical properties of underwater welds. These defects include spatter, porosity, and undercut, which occur in all underwater welding results. The presence of flow and an increased flow rate causes differences in the microstructure, increased porosity on the weld metal, and undercut on the UWW specimen. An increase in water flow rate causes the acicular ferrite microstructure to appear greater, and the heat-affected zone (HAZ) will form finer grains. The best mechanical properties are achieved by welding with the highest flow rate, with a tensile strength of 534.1 MPa, 3.6% elongation, a Vickers microhardness in the HAZ area of 424 HV, and an impact strength of 1.47 J/mm2.

A Drain–Source Connection Technique: Thermal Resistance Measurement Method for GaN HEMTs Using TSEP at High Voltage

2020 ◽  
Vol 67 (12) ◽  
pp. 5454-5459
Author(s):  
Xuan Li ◽  
Shiwei Feng ◽  
Chang Liu ◽  
Yamin Zhang ◽  
Kun Bai ◽  
...  
Keyword(s):  
Thermal Resistance ◽  
High Voltage ◽  
Measurement Method ◽  
Resistance Measurement ◽  
Gan Hemts

scholarly journals Turbine Blade Three-Wavelength Radiation Temperature Measurement Method Based on Reflection Error Correction

2021 ◽  
Vol 11 (9) ◽  
pp. 3913
Author(s):  
Kaifeng Zheng ◽  
Jinguang Lü ◽  
Yingze Zhao ◽  
Jin Tao ◽  
Yuxin Qin ◽  
...  
Keyword(s):  
Temperature Measurement ◽  
Turbine Blade ◽  
Measurement Method ◽  
Turbine Blades ◽  
Target Surface ◽  
Maximum Error ◽  
Radiation Temperature ◽  
Average Error ◽  
Real Surface ◽  
Wavelength Radiation

The turbine blade is a key component in an aeroengine. Currently, measuring the turbine blade radiation temperature always requires obtaining the emissivity of the target surface in advance. However, changes in the emissivity and the reflected ambient radiation cause large errors in measurement results. In this paper, a three-wavelength radiation temperature measurement method was developed, without known emissivity, for reflection correction. Firstly, a three-dimensional dynamic reflection model of the turbine blade was established to describe the ambient radiation of the target blade based on the real surface of the engine turbine blade. Secondly, based on the reflection correction model, a three-wavelength radiation temperature measurement algorithm, independent of surface emissivity, was proposed to improve the measurement accuracy of the turbine blade radiation temperature in the engine. Finally, an experimental platform was built to verify the temperature measurement method. Compared with three conventional colorimetric methods, this method achieved an improved performance on blade temperature measurement, demonstrating a decline in the maximum error from 6.09% to 2.13% and in the average error from 2.82% to 1.20%. The proposed method would benefit the accuracy in the high-temperature measurement of turbine blades.

scholarly journals Design and thermal characteristic analysis of motorized spindle cooling system

2021 ◽  
Vol 13 (5) ◽  
pp. 168781402110208
Author(s):  
Yuan Zhang ◽  
Lifeng Wang ◽  
Yaodong Zhang ◽  
Yongde Zhang
Keyword(s):  
Flow Rate ◽  
High Speed ◽  
Thermal Deformation ◽  
Cooling System ◽  
Thermal Characteristic ◽  
Water Flow Rate ◽  
Thermal Characteristics ◽  
Characteristic Analysis ◽  
Motorized Spindle ◽  
Experiment And Simulation

The thermal deformation of high-speed motorized spindle will affect its reliability, so fully considering its thermal characteristics is the premise of optimal design. In order to study the thermal characteristics of high-speed motorized spindles, a coupled model of thermal-flow-structure was established. Through experiment and simulation, the thermal characteristics of spiral cooling motorized spindle are studied, and the U-shaped cooled motorized spindle is designed and optimized. The simulation results show that when the diameter of the cooling channel is 7 mm, the temperature of the spiral cooling system is lower than that of the U-shaped cooling system, but the radial thermal deformation is greater than that of the U-shaped cooling system. As the increase of the channel diameter of U-shaped cooling system, the temperature and radial thermal deformation decrease. When the diameter is 10 mm, the temperature and radial thermal deformation are lower than the spiral cooling system. And as the flow rate increases, the temperature and radial thermal deformation gradually decrease, which provides a basis for a reasonable choice of water flow rate. The maximum error between experiment and simulation is 2°C, and the error is small, which verifies the accuracy and lays the foundation for future research.

Experimental Characterization of a Modified Airlift Pump

2014 ◽  
Author(s):  
Afshin Goharzadeh ◽  
Keegan Fernandes
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
High Speed ◽  
Water Flow Rate ◽  
High Speed Photography ◽  
Two Phase ◽  
Inner Diameter ◽  
Airlift Pump ◽  
Flow Map ◽  
Churn Flow

This paper presents an experimental investigation on a modified airlift pump. Experiments were undertaken as a function of air-water flow rate for two submergence ratios (ε=0.58 and 0.74), and two different riser geometries (i) straight pipe with a constant inner diameter of 19 mm and (ii) enlarged pipe with a sudden expanded diameter of 19 to 32 mm. These transparent vertical pipes, of 1 m length, were submerged in a transparent rectangular tank (0.45×0.45×1.1 m3). The compressed air was injected into the vertical pipe to lift the water from the reservoir. The flow map regime is established for both configurations and compared with previous studies. The two phase air-water flow structure at the expansion region is experimentally characterized. Pipeline geometry is found to have a significant influence on the output water flow rate. Using high speed photography and electrical conductivity probes, new flow regimes, such as “slug to churn” and “annular to churn” flow, are observed and their influence on the output water flow rate and efficiency are discussed. These experimental results provide fundamental insights into the physics of modified airlift pump.

scholarly journals Impacts of Water Flow Rate on Freezing Prevention of Air-Cooled Heat Exchangers in Power Plants

Energies ◽  
2018 ◽  
Vol 11 (1) ◽  
pp. 112 ◽  
Author(s):  
Yonghong Guo ◽  
Huimin Wei ◽  
Xiaoru Yang ◽  
Weijia Wang ◽  
Xiaoze Du ◽  
...  
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
Heat Exchangers ◽  
Power Plants ◽  
Water Flow Rate
Sign in / Sign up

Export Citation Format

Share Document