Novel Dynamic Numerical Microchannel Evaporator Model to Investigate Parallel Channel Instabilities

2015 ◽  
Author(s):  
Tom Saenen ◽  
John R. Thome
Keyword(s):  
Three Dimensional ◽  
Parallel Channel ◽  
Two Phase ◽  
One Dimensional ◽  
Pressure Losses ◽  
Initial Validation ◽  
Numerical Solver ◽  
The One ◽  
Flow Conservation ◽  
Stability Results

A novel fully dynamic model of a microchannel evaporator is presented. The aim of the model is to study the highly dynamic parallel channel instabilities that occur in these evaporators in more detail. The numerical solver for the model is custom-built and the majority of the paper is focused on detailing the various aspects of this solver. The one-dimensional homogeneous two-phase flow conservation equations are solved to simulate the flow. The full three-dimensional conduction domain of the evaporator is also dynamically resolved. This allows for the correct simulation of the complex hydraulic and thermal interactions between the microchannels that give rise to the parallel channel instabilities. The model uses state-of-the-art correlations to calculate the frictional pressure losses and heat transfer in the microchannels. In addition, a model for inlet restrictions is also included to simulate the stabilizing effect of these components. In the final part of the paper, initial validation results of the model are presented, in which stability results of the model are compared to existing experimental data from literature. Finally, some representative dynamic results are also given to demonstrate some of the unique capabilities of the model.

Dynamic Numerical Microchannel Evaporator Model to Investigate Parallel Channel Instabilities

2016 ◽  
Vol 138 (1) ◽  
Author(s):  
Tom Saenen ◽  
John R. Thome
Keyword(s):  
Three Dimensional ◽  
Solid Substrate ◽  
Parallel Channel ◽  
Two Phase ◽  
Pressure Losses ◽  
Stabilizing Effect ◽  
Substrate Properties ◽  
Numerical Solver ◽  
The Stability ◽  
The One

A fully dynamic model of a microchannel evaporator is presented. The aim of the model is to study the highly dynamic parallel channel instabilities that occur in these evaporators in more detail. The numerical solver for the model is custom-built and the majority of the paper is focused on detailing the various aspects of this solver. The one-dimensional homogeneous two-phase flow conservation equations are solved to simulate the flow. The full three-dimensional (3D) conduction domain of the evaporator is also dynamically resolved. This allows for the correct simulation of the complex hydraulic and thermal interactions between the microchannels that give rise to the parallel channel instabilities. The model uses state-of-the-art correlations to calculate the frictional pressure losses and heat transfer in the microchannels. In addition, a model for inlet restrictions is also included to simulate the stabilizing effect of these components. In the final part of the paper, validation results of the model are presented, in which the stability results of the model are compared with the existing experimental data from the literature. Next, a parametric study is performed focusing on the stabilizing effects of the solid substrate properties. It is found that increasing the thermal conductivity and thickness of the solid substrate has a strong stabilizing effect, while increasing the number of microchannels has a small destabilizing effect. Finally, representative dynamic results are also given to demonstrate some of the unique capabilities of the model.

Exploring the Multidimensional Facets of Authoritarianism: Authoritarian Aggression and Social Dominance Orientation

2008 ◽  
Vol 67 (1) ◽  
pp. 51-60 ◽  
Author(s):  
Stefano Passini
Keyword(s):  
Social Dominance ◽  
Factor Model ◽  
Three Dimensional ◽  
Social Dominance Orientation ◽  
Model Fit ◽  
Regression Analyses ◽  
One Dimensional ◽  
Confirmatory Factor ◽  
The One ◽  
Better Than

The relation between authoritarianism and social dominance orientation was analyzed, with authoritarianism measured using a three-dimensional scale. The implicit multidimensional structure (authoritarian submission, conventionalism, authoritarian aggression) of Altemeyer’s (1981, 1988) conceptualization of authoritarianism is inconsistent with its one-dimensional methodological operationalization. The dimensionality of authoritarianism was investigated using confirmatory factor analysis in a sample of 713 university students. As hypothesized, the three-factor model fit the data significantly better than the one-factor model. Regression analyses revealed that only authoritarian aggression was related to social dominance orientation. That is, only intolerance of deviance was related to high social dominance, whereas submissiveness was not.

On the numerical study of thermohydrodynamics and biochemistry of inland water bodies

2021 ◽  
Author(s):  
Daria Gladskikh ◽  
Evgeny Mortikov ◽  
Victor Stepanenko
Keyword(s):  
Mixed Layer ◽  
Numerical Study ◽  
Three Dimensional ◽  
Water Bodies ◽  
Dimensional Model ◽  
Three Dimensional Model ◽  
One Dimensional ◽  
Lake Model ◽  
Upper Mixed Layer ◽  
The One

<p>The study of thermodynamic and biochemical processes of inland water objects using one- and three-dimensional RANS numerical models was carried out both for idealized water bodies and using measurements data. The need to take into account seiche oscillations to correctly reproduce the deepening of the upper mixed layer in one-dimensional (vertical) models is demonstrated. We considered the one-dimensional LAKE model [1] and the three-dimensional model [2, 3, 4] developed at the Research Computing Center of Moscow State University on the basis of a hydrodynamic code combining DNS/LES/RANS approaches for calculating geophysical turbulent flows. The three-dimensional model was supplemented by the equations for calculating biochemical substances by analogy with the one-dimensional biochemistry equations used in the LAKE model. The effect of mixing processes on the distribution of concentration of greenhouse gases, in particular, methane and oxygen, was studied.</p><p>The work was supported by grants of the RF President’s Grant for Young Scientists (MK-1867.2020.5, MD-1850.2020.5) and by the RFBR (19-05-00249, 20-05-00776). </p><p>1. Stepanenko V., Mammarella I., Ojala A., Miettinen H., Lykosov V., Timo V. LAKE 2.0: a model for temperature, methane, carbon dioxide and oxygen dynamics in lakes // Geoscientific Model Development. 2016. V. 9(5). P. 1977–2006.<br>2. Mortikov E.V., Glazunov A.V., Lykosov V.N. Numerical study of plane Couette flow: turbulence statistics and the structure of pressure-strain correlations // Russian Journal of Numerical Analysis and Mathematical Modelling. 2019. 34(2). P. 119-132.<br>3. Mortikov, E.V. Numerical simulation of the motion of an ice keel in stratified flow // Izv. Atmos. Ocean. Phys. 2016. V. 52. P. 108-115.<br>4. Gladskikh D.S., Stepanenko V.M., Mortikov E.V. On the influence of the horizontal dimensions of inland waters on the thickness of the upper mixed layer // Water Resourses. 2021.V. 45, 9 pages. (in press) </p>

Experimental and Numerical Investigation of Air-Particle Two-Phase Flow in Centrifugal Separator

2000 ◽  
Author(s):  
H. J. Kang ◽  
B. Zheng ◽  
C. X. Lin ◽  
M. A. Ebadian
Keyword(s):  
Velocity Distribution ◽  
Separation Efficiency ◽  
Three Dimensional ◽  
Vertical Direction ◽  
Tangential Direction ◽  
Cylinder Surface ◽  
Centrifugal Separator ◽  
Two Phase ◽  
Dust Collection ◽  
Numerical Solver

Abstract The velocity distributions inside a centrifugal separator with outside and inside diameters of 152.4 mm (6″) and 76.2 mm (3″), respectively, have been investigated experimentally and numerically to obtain optimum separation efficiency. Two 12.7 mm (1/2-inch) holes were drilled on the external surface of the separator to measure the velocity distribution in the separator. Two direction velocities (tangential direction along the cylinder surface and axial along the vertical direction) were measured to compare with the numerical simulation results. A 6060P Pitot probe was employed to obtain the velocity distribution. The dust samples (a mixture of steel particle and dust) from the dust collection box were analyzed using a Phillips XL30 Scanning Electron Microscope. FLUENT code is used as the numerical solver for this fully three-dimensional problem. The fluid flow in the separator is assumed to be steady and incompressible turbulent flow. The standard k–ε model was employed in this study. Non-uniform, unstructured grids are chosen to discretize the entire computation domain. Almost 100,000 cells are used to discretize the whole separator. The constant velocity profile is imposed on the inlet plane. The pressure boundary condition is adopted at outlet plane. Comparing the velocity distribution and separation efficiency from the experiment and the numerical modeling shows that the experimental results and the estimated data agree fairly well and with a deviation within ±10%.

scholarly journals The three dimensional stabilization of superconductivity at 12 K in the one dimensional organic superconductor (TMTSF)2PF6 under 11 kbar

1981 ◽  
Vol 42 (19) ◽  
pp. 445-449 ◽  
Author(s):  
A. Fournel ◽  
C. More ◽  
G. Roger ◽  
J.P. Sorbier ◽  
J.M. Delrieu ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Organic Superconductor ◽  
One Dimensional ◽  
The One

scholarly journals Hydraulic modeling of combined sewers overflow integrating the results of the SWMM and CFX models.

2021 ◽  
Vol 37 (1) ◽  
Author(s):  
D. Pulgarín ◽  
J. Plaza ◽  
J. Ruge ◽  
J. Rojas
Keyword(s):  
Three Dimensional ◽  
Hydraulic Modeling ◽  
Dimensional Model ◽  
Three Dimensional Model ◽  
One Dimensional ◽  
Ansys Cfx ◽  
Combined Sewer ◽  
The One ◽  
Swmm Model

This study proposes a methodology for the calibration of combined sewer overflow (CSO), incorporating the results of the three-dimensional ANSYS CFX model in the SWMM one-dimensional model. The procedure consists of constructing calibration curves in ANSYS CFX that relate the input flow to the CSO with the overflow, to then incorporate them into the SWMM model. The results obtained show that the behavior of the flow over the crest of the overflow weir varies in space and time. Therefore, the flow of entry to the CSO and the flow of excesses maintain a non-linear relationship, contrary to the results obtained in the one-dimensional model. However, the uncertainty associated with the idealization of flow methodologies in one dimension is reduced under the SWMM model with kinematic wave conditions and simulating CSO from curves obtained in ANSYS CFX. The result obtained facilitates the calibration of combined sewer networks for permanent or non-permanent flow conditions, by means of the construction of curves in a three-dimensional model, especially when the information collected in situ is limited.

Modeling of Wall Friction for Multispecies Solid-Gas Flows

1986 ◽  
Vol 108 (4) ◽  
pp. 486-488 ◽  
Author(s):  
E. D. Doss ◽  
M. G. Srinivasan
Keyword(s):  
Shear Stress ◽  
Flow Model ◽  
Flow Characteristics ◽  
Wall Friction ◽  
Gas Flows ◽  
Two Phase ◽  
One Dimensional ◽  
Friction Models ◽  
Wall Interaction ◽  
The One

The empirical expressions for the equivalent friction factor to simulate the effect of particle-wall interaction with a single solid species have been extended to model the wall shear stress for multispecies solid-gas flows. Expressions representing the equivalent shear stress for solid-gas flows obtained from these wall friction models are included in the one-dimensional two-phase flow model and it can be used to study the effect of particle-wall interaction on the flow characteristics.

Sign in / Sign up

Export Citation Format

Share Document