Transient Performance of a Finned PCM Heat Sink

2005 ◽  
Author(s):  
V. Shatikian ◽  
G. Ziskind ◽  
R. Letan
Keyword(s):  
Phase Change ◽  
Melting Temperature ◽  
Phase Change Material ◽  
Heat Sink ◽  
Geometrical Parameters ◽  
Transient Performance ◽  
The Mean ◽  
Liquid States ◽  
Fin Thickness ◽  
Change Material

The present study explores numerically the transient performance of a heat sink based on a phase change material (PCM), during the process of melting. Heat is transferred to the sink through its horizontal base, to which vertical fins made of aluminum are attached. The phase change material is stored between the fins. Its properties, including the melting temperature, latent and sensible specific heat, thermal conductivity and density in solid and liquid states, are based on a commercially available paraffin wax. A parametric investigation is performed for melting in a relatively small system, 10mm high, where the fin thickness is 1.2mm, and the distance between the fins varies from 2mm to 8mm. The temperature of the base varies from 12°C to 24°C above the mean melting temperature of the PCM. Transient numerical simulations are performed, yielding temperature evolution in the fins and the PCM. The computational results show how the transient phase-change process, expressed in terms of the volume melt fraction of the PCM, depends on the thermal and geometrical parameters of the system, which relate to the temperature difference between the base and the mean melting temperature, and to the thickness of the PCM layer.   This paper was also originally published as part of the Proceedings of the ASME 2005 Heat Transfer Summer Conference.

Three-dimensional computational study in a corrugated pipe inserted system filled with phase change material

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ömer Akbal ◽  
Hakan F. Öztop ◽  
Nidal H. Abu-Hamdeh
Keyword(s):  
Phase Change ◽  
Phase Change Material ◽  
Computational Analysis ◽  
Computational Study ◽  
Three Dimensional ◽  
Simple Algorithm ◽  
Melting Time ◽  
Geometrical Parameters ◽  
Content Type ◽  
Change Material

Purpose The purpose of this paper is to make a three-dimensional computational analysis of melting in corrugated pipe inserted system filled with phase change material (PCM). The system was heated from the inner pipe, and temperature of the outer pipe was lower than that of inner pipe. Different geometrical ratio cases and two different temperature differences were tested for their effect on melting time. Design/methodology/approach A computational analysis through a pipe with corrugated pipe filled with PCM is analyzed. Finite volume method was applied with the SIMPLE algorithm method to solve the governing equations. Findings The results indicate that the geometrical parameters can be used to control the melting time inside the heat exchanger which, in turn, affect the energy efficiency. The fastest melting time is seen in Case 4 at the same temperature difference which is the major observation of the current work. Originality/value Originality of this work is to perform a three-dimensional analysis of melting of PCM in a corrugated pipe inserted pipe.

Thermal performance of a phase change material-based heat sink in presence of nanoparticles and metal-foam to enhance cooling performance of electronics

2022 ◽  
Vol 48 ◽  
pp. 103882
Author(s):  
Adeel Arshad ◽  
Mark Jabbal ◽  
Hamza Faraji ◽  
Pouyan Talebizadehsardari ◽  
Muhammad Anser Bashir ◽  
...  
Keyword(s):  
Phase Change ◽  
Phase Change Material ◽  
Thermal Performance ◽  
Heat Sink ◽  
Metal Foam ◽  
Cooling Performance ◽  
Change Material

Operational Time and Melt Fraction Based Optimization of a Phase Change Material Longitudinal Fin Heat Sink

2018 ◽  
Vol 10 (6) ◽  
Author(s):  
D. Jaya Krishna
Keyword(s):  
Phase Change ◽  
Phase Change Material ◽  
Heat Sink ◽  
Fluid Model ◽  
Melting Behavior ◽  
Base Temperature ◽  
Critical Temperatures ◽  
Volume Of Fluid Model ◽  
Change Material ◽  
Operational Time

Abstract In the present study, the numerical investigation has been performed for a phase change material (PCM)-based longitudinal fin heat sink. The fins are taken as an integral part of the heat sink and are made up of aluminum. The PCM considered in the study is RT44HC. Heat is transferred to the heat sink through its horizontal base. In order to simulate the melting behavior of the PCM, volume of fluid model has been used. To attain the best configuration with optimum operational time, Taguchi method has been used followed by analysis of melt fraction and maximum base temperature. The optimized heat sink configuration with maximum operational time has been obtained at the critical temperatures of 54.8 °C, 63 °C, and 72.6 °C.

Effect of Aerogel Incorporation in PCM-Containing Thermal Liner of Firefighting Garment

2018 ◽  
Vol 36 (3) ◽  
pp. 151-164 ◽  
Author(s):  
Abu Shaid ◽  
Lijing Wang ◽  
Stanley M. Fergusson ◽  
Rajiv Padhye
Keyword(s):  
Thermal Properties ◽  
Thermal Resistance ◽  
Heat Resistance ◽  
Phase Change ◽  
Phase Change Material ◽  
Protective Clothing ◽  
Ignition Time ◽  
Current Case ◽  
The Mean ◽  
Change Material

Phase change material (PCM) in firefighting garment enhances protection and comfort. Wearing a protective clothing containing PCM, while fighting the fire, is a direct risk to the wearer as most PCMs used are flammable. This article reports a solution by using aerogel. Thermal liner fabric was treated with PCM and/or aerogel and then their thermal properties were analyzed. It has been found that the mean ignition time of PCM-containing thermal liner is around 3.3 s in current case while this value significantly increased to 5.5 s when the combination of aerogel and PCM was used. Moreover, the weight of the liner fabric with aerogel decreased in comparison to PCM-containing liner. Aerogel also slowed down the spreading of flame in PCM-containing fabric. Aerogel–coated liner showed superior heat resistance and the combination of aerogel with PCM increased the thermal resistance of PCM-containing liner.

Sign in / Sign up

Export Citation Format

Share Document