The Effect of Multiple Reflow Times on Lead-Free Solder Joint Microstructure

2003 ◽  
Author(s):  
Sami T. Nurmi ◽  
Janne J. Sundelin ◽  
Eero O. Ristolainen ◽  
Toivo K. Lepisto¨
Keyword(s):  
Solder Joint ◽  
Solder Joints ◽  
Lead Free ◽  
Lead Free Solder ◽  
Solder Paste ◽  
Snagcu Solder ◽  
Silver Copper ◽  
Free Solder ◽  
Tin Silver Copper ◽  
Lead Free Solders

As environmental issues are raising more interest and are becoming crucial factors in all parts of the world, more and more environmental-friendly electronics products are emerging. Usually this means the introduction of products with lead-free solders. However, the reliability of lead-free solders is still a serious concern despite the vast research done in this field. This paper will describe the interconnect reliability of three kinds of solder joints respectively prepared with lead-free solder paste and lead-free PBGA components, lead-free solder paste and tin-lead-silver PBGA components, and tin-lead solder paste and tin-lead-silver PBGA components. Lead-free and tin-lead solders were composed of eutectic tin-silver-copper and tin-lead, respectively. In addition, the study also presents the effect of multiple reflow times. The study focuses on the microstructures of different assemblies. The particular interest is on the assemblies soldered with lead-free solder paste and tin-lead-silver PBGA components, since the SnPbAg solder on the bumps of the PBGA components were exposed to the reflow profile meant for the lead-free SnAgCu solder. Thus, these SnPbAg solder bumps were in the molten state almost twice as long as the rest of the solders. This had a notable effect on the reliability of these solder joints as we will be showing later in this paper. The test boards were temperature-cycled for 2500 cycles between −40 and +125°C (a 30-minute cycle). PBGA solder joint failures were monitored with a real time monitoring system. Optical and scanning electron microscopy was used to inspect the broken solder joints and their microstructure. The results of tests indicate that the number of reflow times can significantly affect the lifetime of PBGA solder joints. The most notable changes can be seen in the solder joints made with tin-lead-silver PBGA components and tin-silver-copper solder paste soldered with a lead-free reflow profile. The general trend was that the reliability of the solder joints increased in proportion to the number of reflow times. Mainly two factors are believed to have the major effect on the reliability of PBGA solder joints, voids, and microstructural changes in solder.

SAC–xTiO2 nano-reinforced lead-free solder joint characterizations in ultra-fine package assembly

2018 ◽  
Vol 30 (1) ◽  
pp. 1-13 ◽  
Author(s):  
Fakhrozi Che Ani ◽  
Azman Jalar ◽  
Abdullah Aziz Saad ◽  
Chu Yee Khor ◽  
Roslina Ismail ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Solder Joint ◽  
Solder Joints ◽  
Ion Beam ◽  
Lead Free ◽  
Lead Free Solder ◽  
Solder Paste ◽  
Content Type ◽  
X Ray ◽  
Free Solder

Purpose This paper aims to investigate the characteristics of ultra-fine lead-free solder joints reinforced with TiO2 nanoparticles in an electronic assembly. Design/methodology/approach This study focused on the microstructure and quality of solder joints. Various percentages of TiO2 nanoparticles were mixed with a lead-free Sn-3.5Ag-0.7Cu solder paste. This new form of nano-reinforced lead-free solder paste was used to assemble a miniature package consisting of an ultra-fine capacitor on a printed circuit board by means of a reflow soldering process. The microstructure and the fillet height were investigated using a focused ion beam, a high-resolution transmission electron microscope system equipped with an energy dispersive X-ray spectrometer (EDS), and a field emission scanning electron microscope coupled with an EDS and X-ray diffraction machine. Findings The experimental results revealed that the intermetallic compound with the lowest thickness was produced by the nano-reinforced solder with a TiO2 content of 0.05 Wt.%. Increasing the TiO2 content to 0.15 Wt.% led to an improvement in the fillet height. The characteristics of the solder joint fulfilled the reliability requirements of the IPC standards. Practical implications This study provides engineers with a profound understanding of the characteristics of ultra-fine nano-reinforced solder joint packages in the microelectronics industry. Originality/value The findings are expected to provide proper guidelines and references with regard to the manufacture of miniaturized electronic packages. This study also explored the effects of TiO2 on the microstructure and the fillet height of ultra-fine capacitors.

An Investigation of the Lead-Free Surface Mount Soldering Process: Solder Joint Evaluation and Process Optimisation

2004 ◽  
Author(s):  
Claire Ryan ◽  
Jeff M. Punch ◽  
Bryan Rodgers ◽  
Greg Heaslip ◽  
Shane O’Neill ◽  
...  
Keyword(s):  
Screen Printing ◽  
Solder Joints ◽  
Lead Free ◽  
Lead Free Solder ◽  
Solder Paste ◽  
Surface Mount ◽  
Snagcu Solder ◽  
Soldering Process ◽  
Free Process ◽  
Free Solder

A European Union ban on lead in most electrical and electronic equipment will be imposed as of July 1st 2006. The ban, along with market pressures, means that manufacturers must transfer from a tin-lead soldering process to a lead-free process. In this paper the implications on the surface mount (SMT) soldering process are presented. A set of experiments was conducted to investigate the screen-printing and reflow steps of the SMT process using a tin-silver-copper (95.5Sn3.8Ag0.7Cu) solder and a baseline of standard tin-lead (63Sn37Pb). 10×10 arrays of micro Ball Grid Array (micro-BGA) components mounted on 8-layer FR4 printed wiring boards (PWBs) were used. The screen-printing experiment addressed the deposition of the solder paste on the board. The parameters used in the investigation were print speed, squeegee pressure, snap-off distance, separation speed and cleaning interval, with the responses being measurements of paste height and volume. Optimum screen-printer settings were determined which give adequate paste volume and height and a good print definition. The reflow experiment investigated the following parameters of the temperature profile: preheat, soak, peak and cool down temperatures, and conveyor speed. The resulting solder joints were evaluated using cross-section analysis and x-ray techniques in order to determine the presence of defects. A mechanical fatigue test was also carried out in order to compare the strength of the solder joints. The overall quality of the lead-free solder joints was determined from these tests and compared to that of tin-lead. The outcome is a set of manufacturing guidelines for transferring to lead-free solder including optimum screen-printer and reflow oven settings for use with an SnAgCu solder.

Quantitative Evaluation of Voids in Lead Free Solder Joints

2015 ◽  
Vol 772 ◽  
pp. 284-289 ◽  
Author(s):  
Sabuj Mallik ◽  
Jude Njoku ◽  
Gabriel Takyi
Keyword(s):  
Solder Bump ◽  
Solder Joints ◽  
Void Formation ◽  
Lead Free ◽  
Lead Free Solder ◽  
Solder Paste ◽  
X Ray ◽  
Size And Shape ◽  
Solder Bumps ◽  
Free Solder

Voiding in solder joints poses a serious reliability concern for electronic products. The aim of this research was to quantify the void formation in lead-free solder joints through X-ray inspections. Experiments were designed to investigate how void formation is affected by solder bump size and shape, differences in reflow time and temperature, and differences in solder paste formulation. Four different lead-free solder paste samples were used to produce solder bumps on a number of test boards, using surface mount reflow soldering process. Using an advanced X-ray inspection system void percentages were measured for three different size and shape solder bumps. Results indicate that the voiding in solder joint is strongly influenced by solder bump size and shape, with voids found to have increased when bump size decreased. A longer soaking period during reflow stage has negatively affectedsolder voids. Voiding was also accelerated with smaller solder particles in solder paste.

Solder Joint Reliability of Sn-Cu and Sn-Ag-Cu Lead-Free Solder Alloys Solidified on Copper Substrates with Different Surface Roughnesses

2015 ◽  
Vol 830-831 ◽  
pp. 265-269
Author(s):  
Satyanarayan ◽  
K.N. Prabhu
Keyword(s):  
Solder Joint ◽  
Solder Matrix ◽  
Lead Free ◽  
Lead Free Solder ◽  
Solder Alloys ◽  
Cu Substrate ◽  
Cu Substrates ◽  
Free Solder ◽  
Substrate Surfaces ◽  
Lead Free Solders

In the present work, the bond strength of Sn-0.7Cu, Sn-0.3Ag-0.7Cu, Sn-2.5Ag-0.5Cu and Sn-3Ag-0.5Cu lead free solders solidified on Cu substrates was experimentally determined. The bond shear test was used to assess the integrity of Sn–Cu and Sn–Ag–Cu lead-free solder alloy drops solidified on smooth and rough Cu substrate surfaces. The increase in the surface roughness of Cu substrates improved the wettability of solders. The wettability was not affected by the Ag content of solders. Solder bonds on smooth surfaces yielded higher shear strength compared to rough surfaces. Fractured surfaces revealed the occurrence of ductile mode of failure on smooth Cu surfaces and a transition ridge on rough Cu surfaces. Though rough Cu substrate improved the wettability of solder alloys, solder bonds were sheared at a lower force leading to decreased shear energy density compared to the smooth Cu surface. A smooth surface finish and the presence of minor amounts of Ag in the alloy improved the integrity of the solder joint. Smoother surface is preferable as it favors failure in the solder matrix.

Effect of Aging on the Properties of Intermetallic Layers in SAC+Bi Solder Joints

2021 ◽  
Author(s):  
Mohammad Ashraful Haq ◽  
Mohd Aminul Hoque ◽  
Jeffrey C. Suhling ◽  
Pradeep Lall
Keyword(s):  
Solder Joints ◽  
Lead Free ◽  
Lead Free Solder ◽  
Aging Condition ◽  
Sac305 Solder ◽  
The Poor ◽  
Free Solder ◽  
Lead Free Solders ◽  
Overall Reliability ◽  
Intermetallic Layers

Abstract A major problem faced by electronic packaging industries is the poor reliability of lead free solder joints. One of the most common methods utilized to tackle this problem is by doping the alloy with other elements, especially bismuth. Researches have shown Bismuth doped solder joints to mostly fail near the Intermetallic (IMC) layer rather than the bulk of the solder joint as commonly observed in traditional SAC305 solder joints. An understanding of the properties of this IMC layer would thus provide better solutions on improving the reliability of bismuth doped solder joints. In this study, the authors have used three different lead free solders doped with 1%, 2% and 3% bismuth. Joints of these alloys were created on copper substrates. The joints were then polished to clearly expose the IMC layers. These joints were then aged at 125 °C for 0, 1, 2, 5 and 10 days. For each aging condition, the elastic modulus and the hardness of the IMC layers were evaluated using a nanoindenter. The IMC layer thickness and the chemical composition of the IMC layers were also determined for each alloy at every aging condition using Scanning Electron Microscopy (SEM) and EDS. The results from this study will give a better idea on how the percentage of bismuth content in lead free solder affects the IMC layer properties and the overall reliability of the solder joints.

Nanoindentation Characterization of Lead-free Solders and Intermetallic Compounds under Thermal Aging

2010 ◽  
Vol 2010 (1) ◽  
pp. 000314-000318
Author(s):  
Tong Jiang ◽  
Fubin Song ◽  
Chaoran Yang ◽  
S. W. Ricky Lee
Keyword(s):  
Mechanical Properties ◽  
Thermal Aging ◽  
Solder Joints ◽  
Lead Free ◽  
Small Range ◽  
Lead Free Solder ◽  
Solder Alloys ◽  
Aging Test ◽  
Free Solder ◽  
Lead Free Solders

The enforcement of environmental legislation is pushing electronic products to take lead-free solder alloys as the substitute of traditional lead-tin solder alloys. Applications of such alloys require a better understanding of their mechanical behaviors. The mechanical properties of the lead-free solders and IMC layers are affected by the thermal aging. The lead-free solder joints on the pads subject to thermal aging test lead to IMC growth and cause corresponding reliability concerns. In this paper, the mechanical properties of the lead-free solders and IMCs were characterized by nanoindentation. Both the Sn-rich phase and Ag3Sn + β-Sn phase in the lead-free solder joint exhibit strain rate depended and aging soften effect. When lead-free solder joints were subject to thermal aging, Young's modulus of the (Cu, Ni)6Sn5 IMC and Cu6Sn5 IMC changed in very small range. While the hardness value decreased with the increasing of the thermal aging time.

The Effects of Electromigration to the Solder Joint Formation: A Comparison Between 99.3Sn-0.7Cu and 96.5Sn-3.0Ag-0.5Cu Lead Free Solder

2012 ◽  
Vol 622-623 ◽  
pp. 195-199 ◽  
Author(s):  
M.A.A. Mohd Salleh ◽  
A.R. Nik Nurhidayatul Suhada ◽  
Flora Somidin ◽  
Rafezi Ahmad Khairel ◽  
C.S. Lee ◽  
...  
Keyword(s):  
Solder Joint ◽  
Room Temperature ◽  
Solder Joints ◽  
Research Work ◽  
Cathode Region ◽  
Lead Free ◽  
Lead Free Solder ◽  
Joint Formation ◽  
Current Stress ◽  
Free Solder

Electromigration effects on the solder joint formation of 99.3Sn-0.7Cu and 96.5Sn-3.0Ag-0.5Cu lead-free solder with Cu electroplated Ni layer wire were investigated. The electromigration effects on the solder joints were studied after current density stressing at 1 x 103 A/cm2 in room temperature for 0 h, 120 h, and 240 h. The research work found that intermetallic compound (IMC) formation on the joint is increases for both solders with longer period of current stress applied. Higher IMC thickness growth in 99.3Sn-0.7Cu solder joint compared to 99.3Sn-0.7Cu is detected and both anode regions of the solder joints show higher IMC thickness growth compared to cathode region. Experimental results show 99.3Sn-0.7Cu solder joint is more prone to failure under current stress compared to 96.5Sn-3.0Ag-0.5Cu solder joint with thicker IMC which translates to higher brittleness.

Thermal Cycling Reliability of Chip Resistor Lead Free Solder Joints

2003 ◽  
Author(s):  
N. Islam ◽  
J. C. Suhling ◽  
P. Lall ◽  
T. Shete ◽  
H. S. Gale ◽  
...  
Keyword(s):  
Solder Joint ◽  
Thermal Cycling ◽  
Fatigue Resistance ◽  
Solder Joints ◽  
Lead Free ◽  
Lead Free Solder ◽  
Snagcu Alloy ◽  
Temperature Ranges ◽  
Free Solder

In this study, we have examined the thermal cycling reliability of several lead free chip resistor solder joint configurations. Five sizes of resistors (2512, 1206, 0805, 0603, 0402), 2 temperature ranges (−40 to 125°C and −40 to 150°C), and five different solder types have been examined. The solders include the normal SnAgCu alloy recommended by earlier studies (95.5Sn-3.8Ag-0.7Cu), and several variations that include small percentages of Bismuth and Indium to enhance fatigue resistance. Results have been compared to data for standard 63Sn-37Pb joints.

Deformation Behavior of SAC305 Solder Joints With Multiple Grains

2020 ◽  
Author(s):  
Debabrata Mondal ◽  
Abdullah Fahim ◽  
KM Rafidh Hassan ◽  
Jeffrey C. Suhling ◽  
Pradeep Lall
Keyword(s):  
Grain Size ◽  
Solder Joint ◽  
Deformation Behavior ◽  
Thermal Loading ◽  
Solder Joints ◽  
Lead Free ◽  
External Loading ◽  
Lead Free Solder ◽  
Material Anisotropy ◽  
Free Solder

Abstract Lead-free solder joints are the most widely used interconnects in electronic packaging industries. Usually solder joints in most of the electronic devices are exposed to an environment where variation of temperature exists, which indicates cyclic thermal loading to be a very common type of external loading. Moreover, due to difference in the coefficient of thermal expansion (CTE) among dissimilar contact materials, shear stress develops in junctions under thermal loading, which significantly deteriorates the overall reliability. Hence, characterization of lead-free solder materials under thermal loading is essential to predict the performance and deformation behavior of joints in practical applications. A significant portion of the studies in this field are concerned with thermal loading of lead-free solder interconnects, each of which has a very small diameter, in sub-millimeter range. Although the solder balls have very small dimensions, most of the analyses considered them as a bulk material with homogeneous and isotropic properties. However, with the decrease of specimen dimensions, size effects and material directionality play a significant role in deformation mechanisms. Since a very few grains exist in a small specimen, individual grain properties play a vital role on overall material response. Therefore, modeling from the grain structure and orientation point of view could be an effective and more accurate way to predict solder joint deformation behavior under thermal loading. In this study, the effect of grain size and orientation of SAC305 is investigated for predicting anisotropic behavior of solder joints under thermal load. A simplified three-dimensional model of beach-ball configuration solder joint was generated and simulated using ABAQUS finite element (FE) software. Experimentally obtained directional properties such as elastic modulus and CTE were assigned to the computational geometry to create material anisotropy. The effects of material anisotropy were studied for varying grain size specimens, as well as for specimens with varying grain orientation.

Effect of Micro Structure on Fatigue Characteristics of Lead Free Solder Joints

2011 ◽  
Author(s):  
Takahiro Akutsu ◽  
Qiang Yu
Keyword(s):  
Grain Size ◽  
Fatigue Crack ◽  
Fatigue Life ◽  
Solder Joint ◽  
Crack Propagation ◽  
Solder Joints ◽  
Lead Free ◽  
Lead Free Solder ◽  
Micro Structure ◽  
Free Solder

This paper presents the influence of the micro structure on the crack propagation in lead free solder joint. The author’s group have studied the Manson-Coffin’s law for lead free solder joint by using the isothermal fatigue test and FEM analytical approaches to establish the practicable evaluation of thermal fatigue life of solder joints, for example, for the Sn-Cu-Ni solder, because this solder is attracted from the aspect of the decrease of solder leach in the flow process and material cost. However, even if the same loading is given to the solder joints of BGA test piece, there was a large dispersion in the fatigue life. Even though the effect of the shape difference has been considered, the range of the dispersion could not been explained sufficiently. In the study, the fatigue crack propagation modes in the solder joints were investigated, and an internal fatigue crack mode and an interfacial fatigue crack mode were confirmed. And the tendency of a shorter on fatigue life in the interfacial fatigue mode was confirmed. To clarify the mechanism of these fatigue crack modes, the crystal grain size in the solder joints was investigated before the fatigue test and also after the test. Furthermore, the verification of the mechanism using FEM models considering the crystal grain size was carried out. First of all, each element in FEM models matching to the average crystal grain size was made. Second, the inelastic strain ranges in each FEM models were studied. As a result, it was shown that the influence of the crude density of the crystal grain to the fatigue crack progress can be evaluated. In addition, the micro structure of the solder joint of large-scale electronic devices is observed, and FEM model was made based on the observation result. As a result, it was shown that the influence of the directionality with the crystal grain to the fatigue crack progress can be evaluated.

Sign in / Sign up

Export Citation Format

Share Document