Cooling Control Using by Emulsified Heat Transfer Medium

2009 ◽  
Author(s):  
Hiroshi Yamasaki ◽  
Kei Suzuki ◽  
Atsushi Ohashi ◽  
Yasushige Ujiie
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Silicone Oil ◽  
Heat Transfer Medium ◽  
Cooling Control ◽  
Points Of View ◽  
Oil Emulsions ◽  
The Heat Transfer Coefficient ◽  
Temperature Water

Experimental study has been conducted on the heat transfer coefficient control using by the water and silicone oil emulsions. The focus is mainly paid on the effect on the heat transfer of the ambient emulsion temperature, water content and the stirring conditions. Heat transfer on an electrically heated horizontal Pt wire was measured. It is concluded that there is the transition point in the heat transfer coefficient, which is just above the boiling point of emulsified component of water. This may be the potentially useful method for the cooling control. The mechanism of heat transfer of the emulsions has been discussed and revealed for fundamental and practical points of view.

Investigation of the Degree of Augmentation of the Mass Transfer Coefficient of the Heat Transfer Medium in a Vortex Heat Exchanger of a Gas Pressure Regulating and Metering Station Heating System

2021 ◽  
Vol 25 (1) ◽  
pp. 53-65
Author(s):  
N. P. Grigorova ◽  
P. V. Monastyrev ◽  
E. G. Pakhomova ◽  
N. Ye. Semicheva
Keyword(s):  
Heat Transfer ◽  
Mass Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Natural Gas ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Gas Pressure ◽  
Heat Transfer Medium ◽  
The Heat Transfer Coefficient

Purpose of research. is to investigate the degree of augmentation of the mass transfer coefficient of a heat transfer medium in contact with a "spot" of liquid on the surface of the vortex blade when it is bombarded with dispersed contaminants in a vortex heat exchanger in order to identify a pattern that allows obtaining design values of the heat transfer coefficient of the heat transfer medium that have the best agreement with the experimental values provided in previously published articles [4, 6, 7].Methods. A complex analysis of the degree of augmentation of the mass transfer coefficient of the heat transfer medium on the surface of the vortex blade in a vortex heat exchanger based on the known theoretical positions and equations of heat and mass transfer processes.Results. The dependence of the augmentation of the mass transfer coefficient of the heat transfer medium in contact with the "spot" of liquid on the surface of the vortex blade when it is bombarded with dispersed contaminants was obtained, which allows obtaining the best agreement of the design and experimental values of the heat transfer coefficient in the vortex heat exchanger of a gas pressure regulating and metering station.Conclusion. The values of the heat transfer coefficient of the heat transfer medium calculated using the obtained dependence of the augmentation of the mass transfer coefficient of the heat transfer medium have a satisfactory convergence with the experimental data, which allows us to use this dependence in engineering calculations of the design parameters of the vortex heat exchanger used as a heat exchanger for the heating system of the working area of the gas pressure regulating and metering station. This technical solution allows not only saving natural gas as a source of heat generation, but also reducing the negative impact on the environment, since there is no need to burn natural gas. In this case, the production of thermal energy is carried out due to a regulated pressure drop of natural gas coming from the main line to consumers.

Evaporation of lignin-lean black liquor

TAPPI Journal ◽  
2015 ◽  
Vol 14 (7) ◽  
pp. 441-450
Author(s):  
HENRIK WALLMO, ◽  
ULF ANDERSSON ◽  
MATHIAS GOURDON ◽  
MARTIN WIMBY
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Black Liquor ◽  
Salt Content ◽  
Solubility Limit ◽  
Lignin Removal ◽  
Kraft Black Liquor ◽  
Black Liquors ◽  
The Heat Transfer Coefficient

Many of the pulp mill biorefinery concepts recently presented include removal of lignin from black liquor. In this work, the aim was to study how the change in liquor chemistry affected the evaporation of kraft black liquor when lignin was removed using the LignoBoost process. Lignin was removed from a softwood kraft black liquor and four different black liquors were studied: one reference black liquor (with no lignin extracted); two ligninlean black liquors with a lignin removal rate of 5.5% and 21%, respectively; and one liquor with maximum lignin removal of 60%. Evaporation tests were carried out at the research evaporator in Chalmers University of Technology. Studied parameters were liquor viscosity, boiling point rise, heat transfer coefficient, scaling propensity, changes in liquor chemical composition, and tube incrustation. It was found that the solubility limit for incrustation changed towards lower dry solids for the lignin-lean black liquors due to an increased salt content. The scaling obtained on the tubes was easily cleaned with thin liquor at 105°C. It was also shown that the liquor viscosity decreased exponentially with increased lignin outtake and hence, the heat transfer coefficient increased with increased lignin outtake. Long term tests, operated about 6 percentage dry solids units above the solubility limit for incrustation for all liquors, showed that the heat transfer coefficient increased from 650 W/m2K for the reference liquor to 1500 W/m2K for the liquor with highest lignin separation degree, 60%.

scholarly journals Systematic heat transfer measurements in highly viscous binary fluids

2021 ◽  
Author(s):  
Ann-Christin Fleer ◽  
Markus Richter ◽  
Roland Span
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Volatile Component ◽  
Test Tube ◽  
Heat Fluxes ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Low Viscosity ◽  
The Heat Transfer Coefficient

AbstractInvestigations of flow boiling in highly viscous fluids show that heat transfer mechanisms in such fluids are different from those in fluids of low viscosity like refrigerants or water. To gain a better understanding, a modified standard apparatus was developed; it was specifically designed for fluids of high viscosity up to 1000 Pa∙s and enables heat transfer measurements with a single horizontal test tube over a wide range of heat fluxes. Here, we present measurements of the heat transfer coefficient at pool boiling conditions in highly viscous binary mixtures of three different polydimethylsiloxanes (PDMS) and n-pentane, which is the volatile component in the mixture. Systematic measurements were carried out to investigate pool boiling in mixtures with a focus on the temperature, the viscosity of the non-volatile component and the fraction of the volatile component on the heat transfer coefficient. Furthermore, copper test tubes with polished and sanded surfaces were used to evaluate the influence of the surface structure on the heat transfer coefficient. The results show that viscosity and composition of the mixture have the strongest effect on the heat transfer coefficient in highly viscous mixtures, whereby the viscosity of the mixture depends on the base viscosity of the used PDMS, on the concentration of n-pentane in the mixture, and on the temperature. For nucleate boiling, the influence of the surface structure of the test tube is less pronounced than observed in boiling experiments with pure fluids of low viscosity, but the relative enhancement of the heat transfer coefficient is still significant. In particular for mixtures with high concentrations of the volatile component and at high pool temperature, heat transfer coefficients increase with heat flux until they reach a maximum. At further increased heat fluxes the heat transfer coefficients decrease again. Observed temperature differences between heating surface and pool are much larger than for boiling fluids with low viscosity. Temperature differences up to 137 K (for a mixture containing 5% n-pentane by mass at a heat flux of 13.6 kW/m2) were measured.

Test and Analysis on the Heat Transfer Coefficient of the Mixed Plate Heat Exchanger

2014 ◽  
Vol 552 ◽  
pp. 55-60
Author(s):  
Zheng Ming Tong ◽  
Peng Hou ◽  
Gui Hua Qin
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Mixed Mode ◽  
Plate Heat Exchanger ◽  
Plate Heat ◽  
Fitting Method ◽  
Engineering Significance ◽  
The Heat Transfer Coefficient

In this article, we use BR0.3 type plate heat exchanger for experiment,and the heat transfer coefficient of the mixed plate heat exchanger is explored. Through the test platform of plate heat exchanger, a large number of experiments have been done in different mixed mode but the same passageway,and lots experimental data are obtained. By the linear fitting method and the analysis of the data, the main factors which influence the heat transfer coefficient of mixed plate heat exchanger were carried out,and the formula of heat transfer coefficient which fits at any mixed mode plate heat exchanger is obtained, to solve the problem of engineering calculation.The fact , there is no denying that the result which we get has great engineering significance

Identification of three-dimensional transient temperature fields in thick-walled elements using the inverse method

2018 ◽  
Vol 28 (1) ◽  
pp. 138-150 ◽  
Author(s):  
Magdalena Jaremkiewicz
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Inverse Method ◽  
Thermal Stresses ◽  
Computing Time ◽  
Transient Temperature ◽  
Content Type ◽  
Inner Surface ◽  
The Heat Transfer Coefficient

Purpose The purpose of this paper is to propose a method of determining the transient temperature of the inner surface of thick-walled elements. The method can be used to determine thermal stresses in pressure elements. Design/methodology/approach An inverse marching method is proposed to determine the transient temperature of the thick-walled element inner surface with high accuracy. Findings Initially, the inverse method was validated computationally. The comparison between the temperatures obtained from the solution for the direct heat conduction problem and the results obtained by means of the proposed inverse method is very satisfactory. Subsequently, the presented method was validated using experimental data. The results obtained from the inverse calculations also gave good results. Originality/value The advantage of the method is the possibility of determining the heat transfer coefficient at a point on the exposed surface based on the local temperature distribution measured on the insulated outer surface. The heat transfer coefficient determined experimentally can be used to calculate thermal stresses in elements with a complex shape. The proposed method can be used in online computer systems to monitor temperature and thermal stresses in thick-walled pressure components because the computing time is very short.

scholarly journals Comparison of Two-Equation Turbulence Models for Prediction of Heat Transfer on Film-Cooled Turbine Blades

1997 ◽  
Author(s):  
Vijay K. Garg ◽  
Ali A. Ameri
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Computer Time ◽  
Suction Surface ◽  
The Heat Transfer Coefficient

A three-dimensional Navier-Stokes code has been used to compute the heat transfer coefficient on two film-cooled turbine blades, namely the VKI rotor with six rows of cooling holes including three rows on the shower head, and the C3X vane with nine rows of holes including five rows on the shower head. Predictions of heat transfer coefficient at the blade surface using three two-equation turbulence models, specifically, Coakley’s q-ω model, Chien’s k-ε model and Wilcox’s k-ω model with Menter’s modifications, have been compared with the experimental data of Camci and Arts (1990) for the VKI rotor, and of Hylton et al. (1988) for the C3X vane along with predictions using the Baldwin-Lomax (B-L) model taken from Garg and Gaugler (1995). It is found that for the cases considered here the two-equation models predict the blade heat transfer somewhat better than the B-L model except immediately downstream of the film-cooling holes on the suction surface of the VKI rotor, and over most of the suction surface of the C3X vane. However, all two-equation models require 40% more computer core than the B-L model for solution, and while the q-ω and k-ε models need 40% more computer time than the B-L model, the k-ω model requires at least 65% more time due to slower rate of convergence. It is found that the heat transfer coefficient exhibits a strong spanwise as well as streamwise variation for both blades and all turbulence models.

Sign in / Sign up

Export Citation Format

Share Document