A Novel Dynamic Bone Stress Evaluation Method of Postoperative Proximal Femur During Gait by Using Elastic Multi Body Analysis Based on Finite Element Analysis

2017 ◽  
Author(s):  
Yukiko Nakamura ◽  
Kazuhiko Adachi ◽  
Nungna Wi ◽  
Mitsuaki Noda
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Boundary Conditions ◽  
Hip Joint ◽  
Proximal Femur ◽  
Dynamic Stress ◽  
Fe Analysis ◽  
Patient Specific ◽  
Time Varying ◽  
Multi Body

A proximal femur fracture due to osteoporosis is one of serious health care problems in aging societies. Osteosynthesis with pin or screw type of implants, such as Hansson pin (HP), Dual SC Screw (DSCS), is widely used for femoral neck fracture treatment in Japan. Unfortunately, some complications such as secondary fractures, especially peri-prosthetic fractures, may occur during postoperative rehabilitation period. In order to reveal the potential cause of the postoperative fracture from the viewpoint of the biomechanics, authors had already performed the dynamic stress analysis of the treated proximal femur based on finite element (FE) analysis. The final goal of our project is to establish the reliable postoperative bone fracture risk assessment method in response to the daily activity including mainly walking. The aim of this study is to propose a novel elastic multi body analysis method based on FE analysis for proximal femur biomechanics. Patient-specific 3D left hip joint FE model was constructed from an elderly female volunteer’s CT images. The model consists of the pelvis, proximal femur, cartilage and DSCS, as multi bodies. The dynamic loading and boundary conditions were applied to the model for simulating a gait motion. Direction and magnitude of the loads varies in response to the gait motion. The time dependent loading forces; hip contact, gluteus medius, gluteus maximus, tensor fasciae latae and adductor, acting around the hip joint was obtained by inverse dynamic analysis of a human gait using in-house lower-limb musculoskeletal model. These loading and boundary conditions for simulating the gait motion are the major technical advantages of the proposed multi body analysis comparing with the conventional static FE analysis. Time varying stress distribution during the gait was evaluated by using dynamic explicit method via ABAQUS. In order to visually demonstrate dynamic stress distribution, we examined the time varying von Mises stresses at the representative points located on the cortical surface of the proximal femur; femoral head, fracture surface and around the lateral insertion holes. The results indicate significant increase of the stresses around the proximal lateral insertion holes for DSCS treatment. Maximum stress values are good agreement with the previous static FE analysis, on the other hand, these biomechanical discussions based on the stress time histories are only obtained from the proposed method. It is indicated that the proposed method is feasible to support the better pre- and postoperative clinical decisions, which is the main contribution of this study.

Influence of Axial Excitations and of Boundary Conditions on the Parametric Instability of a Beam

1995 ◽  
Author(s):  
Régis Dufour ◽  
Alain Berlioz ◽  
Thomas Streule
Keyword(s):  
Finite Element ◽  
Boundary Conditions ◽  
Ritz Method ◽  
Parametric Instability ◽  
Experimental Tests ◽  
Time Varying ◽  
Periodic Force ◽  
Modal Reduction ◽  
Time Varying Parameter ◽  
The Stability

Abstract In this paper the stability of the lateral dynamic behavior of a pinned-pinned, clamped-pinned and clamped-clamped beam under axial periodic force or torque is studied. The time-varying parameter equations are derived using the Rayleigh-Ritz method. The stability analysis of the solution is based on Floquet’s theory and investigated in detail. The Rayleigh-Ritz results are compared to those of a finite element modal reduction. It shows that the lateral instabilities of the beam depend on the forcing frequency, the type of excitation and the boundary conditions. Several experimental tests enable the validation of the numerical results.

Numerical Study of the Effect of Geometry and Boundary Conditions on the Collapse Behaviour of Stocky Stiffened Panels

2012 ◽  
Vol 154 (A2) ◽  
Keyword(s):  
Finite Element ◽  
Boundary Conditions ◽  
Ultimate Strength ◽  
Material Properties ◽  
Finite Element Modelling ◽  
Numerical Study ◽  
Fe Analysis ◽  
Stiffened Panels ◽  
Element Modelling ◽  
Geometric Configurations

This study aims at studying different configurations of the stiffened panels in order to identify robust configurations that would not be much sensitive to the imprecision in boundary conditions that can exist in experimental set ups. A numerical study is conducted to analyze the influence of the stiffener’s geometry and boundary conditions on the ultimate strength of stiffened panels under uniaxial compression. The stiffened panels with different combinations of mechanical material properties and geometric configurations are considered. The four types of stiffened panels analysed are made of mild or high tensile steel and have bar, ‘L’ and ‘U’ stiffeners. To understand the effect of finite element modelling on the ultimate strength of the stiffened panels, four types of FE models are investigated in FE analysis including 3 bays, 1/2+1+1/2 bays, 1+1 bays and 1 bay with different boundary conditions.

Computer assisted evaluation of plate osteosynthesis of diaphyseal femur fracture considering interfragmentary movement: a finite element study

2017 ◽  
Vol 62 (3) ◽  
Author(s):  
Claudia Wittkowske ◽  
Stefan Raith ◽  
Maximilian Eder ◽  
Alexander Volf ◽  
Jan S. Kirschke ◽  
...  
Keyword(s):  
Finite Element ◽  
Plate Osteosynthesis ◽  
Computation Time ◽  
Fe Analysis ◽  
Patient Specific ◽  
Osteoporotic Bone ◽  
Computer Assisted ◽  
Efficient Computation ◽  
User Input ◽  
Patient Specific Modeling

AbstractA semi-automated workflow for evaluation of diaphyseal fracture treatment of the femur has been developed and implemented. The aim was to investigate the influence of locking compression plating with diverse fracture-specific screw configurations on interfragmentary movements (IFMs) with the use of finite element (FE) analysis. Computed tomography (CT) data of a 22-year-old non-osteoporotic female were used for patient specific modeling of the inhomogeneous material properties of bone. Hounsfield units (HU) were exported and assigned to elements of a FE mesh and converted to mechanical properties such as the Young’s modulus followed by a linear FE analysis performed in a semi-automated fashion. IFM on the near and far cortex was evaluated. A positive correlation between bridging length and IFM was observed. Optimal healing conditions with IFMs between 0.5 mm and 1 mm were found in a constellation with a medium bridging length of 80 mm with three unoccupied screw holes around the fracture gap. Usage of monocortical screws instead of bicortical ones had negligible influence on the evaluated parameters when modeling non-osteoporotic bone. Minimal user input, automation of the procedure and an efficient computation time ensured quick delivery of results which will be essential in a future clinical application.

AN ALGORITHM TO CALCULATE THE COMPONENTS OF ALL MUSCLE FORCES DURING EACH PHASES OF THE GAIT CYCLE, FOR THE PELVIC-FEMUR COMPLEX

2005 ◽  
Vol 05 (04) ◽  
pp. 539-548 ◽  
Author(s):  
SANTANU MAJUMDER ◽  
AMIT ROYCHOWDHURY ◽  
SUBRATA PAL
Keyword(s):  
Finite Element ◽  
Hip Joint ◽  
Computational Models ◽  
Gait Cycle ◽  
Muscle Force ◽  
Fe Analysis ◽  
Muscle Forces ◽  
Force Magnitude ◽  
Flexion Extension ◽  
Force Components

With the help of finite element (FE) computational models of femur, pelvis or hip joint to perform quasi-static stress analysis during the entire gait cycle, muscle force components (X, Y, Z) acting on the hip joint and pelvis are to be known. Most of the investigators have presented only the net muscle force magnitude during gait. However, for the FE software, either muscle force components (X, Y, Z) or three angles for the muscle line of action are required as input. No published algorithm (with flowchart) is readily available to calculate the required muscle force components for FE analysis. As the femur rotates about the hip center during gait, the lines of action for 27 muscle forces are also variable. To find out the variable lines of action and muscle force components (X, Y, Z) with directions, an algorithm was developed and presented here with detailed flowchart. We considered the varying angles of adduction/abduction, flexion/extension during gait. This computer program, obtainable from the first author, is able to calculate the muscle force components (X, Y, Z) as output, if the net magnitude of muscle force, hip joint orientations during gait and muscle origin and insertion coordinates are provided as input.

Flanged Acrylic Plastic Hemispherical Shells for Undersea Application

1975 ◽  
Vol 97 (1) ◽  
pp. 1-9 ◽  
Author(s):  
J. D. Stachiw ◽  
J. R. Maison
Keyword(s):  
Finite Element ◽  
Hydrostatic Pressure ◽  
Stress Distribution ◽  
Boundary Conditions ◽  
Critical Pressure ◽  
Convex Surface ◽  
Elastic Analysis ◽  
Short Term ◽  
Acrylic Plastic ◽  
Hemispherical Shells

The effects of an equatorial flange and a nonuniform wall thickness upon the critical pressure and stress distribution in acrylic plastic hemispheres have been investigated by experimental and analytical methods. Forty acrylic hemispheres were fabricated and tested to destruction under short term hydrostatic pressure applied on the convex surface. Dome apex displacements were obtained from each specimen and strains were obtained from a selected few. A finite element elastic analysis was performed on one window configuration for two different boundary conditions and the experimentally derived stresses were used to determine which boundary conditions was the best for analytical analysis.

FE Analysis and Position Accuracy Estimation of Machining System for Lens of Mobile Devices

2007 ◽  
Vol 364-366 ◽  
pp. 1197-1202
Author(s):  
Seung Yub Baek ◽  
Eun Sang Lee ◽  
Jung Hyung Lee ◽  
Min Jung Shin
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Static Analysis ◽  
Fe Analysis ◽  
Structural Behavior ◽  
Accuracy Estimation ◽  
Aspheric Lens ◽  
Industrial Manufacturing ◽  
Position Accuracy ◽  
Machining System

In order to obtain competitiveness in the field of industrial manufacturing, a reduction in the development period for the batch machining of products is required. It is essential to analyze the stress distribution and deformations of machining system which is used for manufacturing the aspheric lens using FEM software ANSYS. Finite element simulations have been performed in order to study the influence of machining system which was developed in this study on structures. It is very important to understand the structural behavior of machining system. This research investigated the static analysis and dynamic analysis of machining system for aspheric lens to predict the damage due to loading.

Need for CT-based bone density modelling in finite element analysis of a shoulder arthroplasty revealed through a novel method for result analysis

2014 ◽  
Vol 0 (0) ◽  
Author(s):  
Werner Pomwenger ◽  
Karl Entacher ◽  
Herbert Resch ◽  
Peter Schuller-Götzburg
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Bone Density ◽  
Boundary Conditions ◽  
Density Distribution ◽  
Shoulder Arthroplasty ◽  
Cumulative Distribution ◽  
Patient Specific ◽  
Element Analysis ◽  
Shoulder Complex

AbstractTreatment of common pathologies of the shoulder complex, such as rheumatoid arthritis and osteoporosis, is usually performed by total shoulder arthroplasty (TSA). Survival of the glenoid component is still a problem in TSA, whereas the humeral component is rarely subject to failure. To set up a finite element analysis (FEA) for simulation of a TSA in order to gain insight into the mechanical behaviour of a glenoid implant, the modelling procedure and the application of boundary conditions are of major importance because the computed result strongly depends upon the accuracy and sense of realism of the model. The goal of this study was to show the influence on glenoid stress distribution of a patient-specific bone density distribution compared with a homogenous bone density distribution for the purpose of generating a valid model in future FEA studies of the shoulder complex. Detailed information on the integration of bone density properties using existing numerical models as well as the applied boundary conditions is provided. A novel approach involving statistical analysis of values derived from an FEA is demonstrated using a cumulative distribution function. The results show well the mechanically superior behaviour of a realistic bone density distribution and therefore emphasise the necessity for patient-specific simulations in biomechanical and medical simulations.

scholarly journals The Influence of Pelvic Tilt on Stress Distribution in the Acetabulum: Finite Element Analysis

2020 ◽  
Author(s):  
Kazuhiro Hasegawa ◽  
Tamon Kabata ◽  
Yoshitomo Kajino ◽  
Daisuke Inoue ◽  
Jiro Sakamoto ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Hip Joint ◽  
Tilt Angle ◽  
Pelvic Tilt ◽  
Biomechanical Analysis ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Von Mises

Abstract Background Finite element analysis (FEA) has been previously applied for the biomechanical analysis of acetabular dysplasia and osteotomy. However, until now, there have been little reports on the use of FEA to evaluate the effects of pelvic tilt on stress distribution in the acetabulum. Methods We used the Mechanical Finder Ver. 7.0 (RCCM, Inc., Japan) to construct finite element models based on 3D-CT data of patients, and designed dysplasia, borderline, and normal pelvic models. For analysis, body weight was placed on the sacrum and the load of the flexor muscles of the hip joint was placed on the ilium. The pelvic tilt was based on the anterior pelvic plane, and the pelvic tilt angles were -20°, 0°, and 20°. The load of the flexor muscle of the hip joint was calculated using the moment arm equation.Results All three models showed the highest values of von Mises stress in the -20° pelvic tilt angle, and the lowest in the 20° angle. Stress distribution concentrated in the load-bearing area. The maximum values of von Mises stress in the borderline at pelvic tilt angles of -20° was 3.5Mpa, and in the dysplasia at pelvic tilt angles of 0° was 3.1Mpa. Conclusions The pelvic tilt angle of -20° of the borderline model showed equal maximum values of von Mises stress than the dysplasia model of pelvic tilt angle of 0°, indicating that pelvic retroversion of -20° in borderline is a risk factor for osteoarthritis of the hip joints, similar to dysplasia.

Biomechanical Analysis of Selected Endoprostheses of Hip Joint by Means of Finite Element Methods

2015 ◽  
Vol 226 ◽  
pp. 29-32
Author(s):  
Marcin Basiaga ◽  
Joanna Przondziono
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Boundary Conditions ◽  
Hip Joint ◽  
Biomechanical Analysis ◽  
Geometric Features ◽  
The Finite Element Method ◽  
Hip Joint Endoprosthesis ◽  
Selection Of

The main purpose of this paper was biomechanical analysis of hip joint endoprosthesis – femur systems by means of the Finite Element Method. During the analysis two endoprostheses with differential geometric features were selected. Geometric models of analysed implants were compiled on the grounds of real models like Merotan and The DePuy Proxima which were chosen from series diamensional. Afterwards the models were discretization and boundary conditions were set. Those boundary conditions with right accuracy copied a phenomena which occurred in real models - the Pauwels model. The field of analysis involved determination of the state of displacements, strains and stresses which were cut down in the of endoprosthesis – bone systems. The analysis that was carried out constitute the basics for optimisation of implant geometry and right selection of material’s mechanical properties to its production.

Sign in / Sign up

Export Citation Format

Share Document