Numerical Investigation of Effects of Non-Uniform Tip Clearance on Flow Field Inside a Turbine Cascade

2016 ◽  
Author(s):  
Hongwei Ma ◽  
Yangtao Tian
Keyword(s):  
Flow Field ◽  
Suction Side ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Pressure Side ◽  
Turbine Cascade ◽  
Leakage Loss ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Turbine Performance

In the unshrouded axial turbine, the tip clearances can result in the loss of turbine efficiency and the penalty of turbine performance. Therefore, investigating the blade tip geometry of improving the turbine performance has a great significance. This paper is to study the effects of non-uniform tip clearance on the flow field in a turbine cascade. The numerical works are performed at the incidence angle of 0 degree and the exit Reynolds number of 1.7 × 105 based on the blade chord. In the investigations, the flat tip (Basic) geometry was employed as a benchmark, and three different tip geometries, including the pressure side squealer (PSQ), suction side squealer (SSQ) and grooved tip (Grooved), were studied. The tip clearances are all specified as 1.18% of the chord. The squealer height is set to 2.94% of the chord. The endwall static pressure, tip leakage loss, flow capacity and the development of tip leakage vortex are discussed. And the numerical results show that the grooved tip which can obtain the least total pressure loss, is helpful to smooth the pressure change from pressure side to suction side and suppress the intensity of tip leakage vortex. The tip clearance flow in the pre semi-passage is mainly involved in the passage vortex, and in the post semi-passage it is added to the tip leakage vortex. Compared with the Basic, PSQ and SSQ tips, the Grooved tip contributes to reducing the tip leakage flow and the tip leakage loss. And the leakage flow can be strengthened in the middle passage for the PSQ. The difference between the area averaged streamwise coefficient and mass averaged loss is almost opposite for the SSQ and Grooved tip, which is uncertain the performance of the turbine cascade with the SSQ and Grooved tip is better than the Basic tip.

Effects of Tip Clearance on Unsteady Flow Characteristics in an Axial Turbine Stage

2009 ◽  
Author(s):  
Hao Sun ◽  
Jun Li ◽  
Zhenping Feng
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Rotor Blade ◽  
Suction Side ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Turbine Stage ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Blade Tip

The clearance between the rotor blade tip and casing wall in turbomachinery passages induces leakage flow loss and thus degrades aerodynamic performance of the machine. The flow field in turbomachinery is significantly influenced by the rotor blade tip clearance size. To investigate the effects of tip clearance size on the rotor-stator interaction, the turbine stage profile from Matsunuma’s experimental tests was adopted, and the unsteady flow fields with two tip clearance sizes of 0.67% and 2.00% of blade span was numerical simulated based on Harmonic method using NUMECA software. By comparing with the domain scaling method, the accuracy of the harmonic method was verified. The interaction mechanism between the stator wake and the leakage flow was investigated. It is found that the recirculation induced by the stator wake is separated by a significant “interaction line” from the flow field close to the suction side in the clearance region. The trend of the pressure fluctuation is contrary on both sides of the line. When the stator wakes pass by the suction side, the pressure field fluctuates and the intensity of the tip leakage flow varies. With the clearance size increasing, the “interaction line” is more far away from the suction side and the intensity of tip leakage flow also fluctuates more strongly.

PIV Maps of Tip Leakage and Secondary Flow Fields on a Low-Speed Turbine Blade Cascade With Moving End Wall

2007 ◽  
Vol 130 (1) ◽  
Author(s):  
P. Palafox ◽  
M. L. G. Oldfield ◽  
J. E. LaGraff ◽  
T. V. Jones
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Field Measurements ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Low Speed ◽  
Tip Leakage ◽  
End Wall

New, detailed flow field measurements are presented for a very large low-speed cascade representative of a high-pressure turbine rotor blade with turning of 110deg and blade chord of 1.0m. Data were obtained for tip leakage and passage secondary flow at a Reynolds number of 4.0×105, based on exit velocity and blade axial chord. Tip clearance levels ranged from 0% to 1.68% of blade span (0% to 3% of blade chord). Particle image velocimetry was used to obtain flow field maps of several planes parallel to the tip surface within the tip gap, and adjacent passage flow. Vector maps were also obtained for planes normal to the tip surface in the direction of the tip leakage flow. Secondary flow was measured at planes normal to the blade exit angle at locations upstream and downstream of the trailing edge. The interaction between the tip leakage vortex and passage vortex is clearly defined, revealing the dominant effect of the tip leakage flow on the tip end-wall secondary flow. The relative motion between the casing and the blade tip was simulated using a motor-driven moving belt system. A reduction in the magnitude of the undertip flow near the end wall due to the moving wall is observed and the effect on the tip leakage vortex examined.

PIV Maps of Tip Leakage and Secondary Flow Fields on a Low Speed Turbine Blade Cascade With Moving Endwall

2005 ◽  
Author(s):  
P. Palafox ◽  
M. L. G. Oldfield ◽  
J. E. LaGraff ◽  
T. V. Jones
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Field Measurements ◽  
Turbine Rotor ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Low Speed ◽  
Tip Leakage

New, detailed flow field measurements are presented for a very large low-speed cascade representative of a high-pressure turbine rotor blade with turning of 110 degrees and blade chord of 1.0 m. Data was obtained for tip leakage and passage secondary flow at a Reynolds number of 4.0 × 105, based on exit velocity and blade axial chord. Tip clearance levels ranged from 0% to 1.68% of blade span (0% to 3% of blade chord). Particle Image Velocimetry (PIV) was used to obtain flow field maps of several planes parallel to the tip surface within the tip gap, and adjacent passage flow. Vector maps were also obtained for planes normal to the tip surface in the direction of the tip leakage flow. Secondary flow was measured at planes normal to the blade exit angle at locations upstream and downstream of the trailing edge. The interaction between the tip leakage vortex and passage vortex is clearly defined, revealing the dominant effect of the tip leakage flow on the tip endwall secondary flow. The relative motion between the casing and the blade tip was simulated using a motor-driven moving belt system. A reduction in the magnitude of the under-tip flow near the endwall due to the moving wall is observed and the effect on the tip leakage vortex examined.

Experiment study of the winglet-cavity tip on the aerodynamic performance in a turbine cascade

2017 ◽  
Vol 231 (7) ◽  
pp. 676-685 ◽  
Author(s):  
Shaowen Chen ◽  
Zhihua Zhou ◽  
Qinghe Meng ◽  
Songtao Wang ◽  
Xun Zhou
Keyword(s):  
Flow Field ◽  
Total Pressure ◽  
Static Pressure ◽  
Aerodynamic Performance ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Passage Vortex ◽  
Side Gap

The effects of a novel winglet-cavity tip on the flow field and aerodynamic performance of a turbine blade with tip clearance have been investigated in a low-speed wind tunnel. A calibrated five-hole probe is used for the measurement of three-dimensional flows downstream of the cascade. The method of oil-flow visualization is used to show the endwall flow field structure. The distribution of endwall static pressure is measured particularly by using the special moveable endwall. The downstream results show that, compared with the flat tip and cavity tip, the winglet-cavity tip reduces aerodynamic loss in the region of tip leakage vortex and passage vortex effectively and gives a 8.5% reduction of total pressure losses at a tip clearance of τ/ H = 1.0%. Meanwhile, a more uniform flow angle is obtained with the winglet-cavity tip. Thus, the winglet-cavity tip provides better aerodynamic performance. It was found that more endwall flow enters the cavity from the front of suction side gap, combines with the flow entering the tip from the pressure side, and then separates upon the cavity. This reduces the loss of passage vortex. The endwall static pressure indicates that the winglet-cavity tip reduces the driving pressure difference and weakens the tip leakage flow. With the tip clearance increasing, the leakage flow is significantly enhanced. This strengthens the interaction between the tip leakage vortex and the passage vortex. With respect to the flat tip and cavity tip, the winglet-cavity tip obtains the lowest total pressure loss at all tested tip clearances.

An Experimental Investigation of the Effects of Grooved Tip Geometry on the Flow Field in a Turbine Cascade Passage Using Stereoscopic PIV

2017 ◽  
Author(s):  
Yangtao Tian ◽  
Hongwei Ma ◽  
Lixiang Wang
Keyword(s):  
Flow Field ◽  
Vortex Breakdown ◽  
Tracer Particle ◽  
Tip Clearance ◽  
Small Scale ◽  
Turbine Cascade ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Turbine Efficiency

In the unshrouded axial turbine, the tip clearance gap can cause the losses of turbine efficiency and the penalty of turbine performance. Based on previous investigations, changing the blade tip geometry plays an important role in improving the turbine efficiency and performance. In this paper, the Stereoscopic Particle Imaging Velocimetry (SPIV) measurements were conducted to study the effects of grooved tip geometry on the flow field inside a turbine cascade passage. During the measurements, the double-frame CCD cameras were configured at different sides of the laser light sheet. Additionally, the Diisooctyl Sebacate (DEHS) was treated as the tracer particle. The tip clearance gap of both grooved tip and flat tip was set to 1.18% of the blade chord. The groove height was specified as 2.94% of the blade chord. In this study, the flow field results of eight measured planes were presented. Some typical features of the complicated flow structures, such as tip leakage vortex formation, development, breakdown and the dissipation, the variations of turbulence intensity and Reynolds stress, the blockage characteristic, were discussed as well. The experimental results show that the tip leakage flow/vortex is weakened by the grooved tip. The blockage effect and the flow capacity of the turbine passage are also improved. The tip leakage vortex breaks down at about 70% camber line, but the pattern of leakage vortex has changed into an ellipse at 60% camber line, which is an indication of the vortex breakdown. As for the decomposed and reconstructed flow, the first modal flow is the most similar to the original flow field. And it can capture the dominant flow features in flow field. And the flow of mode 2 and mode 3 generates many eddies with small scale.

scholarly journals Influence of Tip Clearance on Flow Characteristics of Axial Compressor

Processes ◽  
2020 ◽  
Vol 8 (11) ◽  
pp. 1445
Author(s):  
Moru Song ◽  
Hong Xie ◽  
Bo Yang ◽  
Shuyi Zhang
Keyword(s):  
Flow Field ◽  
Flow Characteristics ◽  
Axial Compressor ◽  
Suction Side ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Tip Clearance Vortex

This paper studies the influence of tip clearance on the flow characteristics related to the performance. Based on full-passage numerical simulation with experimental validation, several clearance models are established and the performance curves are obtained. It is found that there exists an optimum clearance for the stable working range. By analyzing the flow field in tip region, the role of the tip leakage flow is illustrated. In the zero-clearance model, the separation and blockage along the suction side is the main reason for rotating stall. As the tip clearance is increased to the optimum value, the separation is suppressed by the tip leakage flow. However, with the continuing increasing of the tip clearance, the scale and strength of the tip clearance vortex is increased correspondingly. When the tip clearance is larger than the optimum value, the tip clearance vortex gradually dominates the flow field in the tip region, which can increase the unsteadiness in the tip region and trigger forward spillage in stall onset.

Impact of Sinusoidal Tip Gaps on Axial Compressor Rotor Performance: A Flow Field Investigation

2019 ◽  
Author(s):  
Shraman Goswami ◽  
Ashima Malhotra
Keyword(s):  
Flow Field ◽  
Axial Compressor ◽  
Field Investigation ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Stall Margin ◽  
Tip Leakage ◽  
Compressor Rotor

Abstract Performance of an axial compressor rotor depends largely on the tip leakage flow. Tip leakage flow results in tip leakage vortex which is a source of loss. This has an impact on the compressor efficiency as well as stall margin. A lot of work has been done to understand the tip leakage flow and controlling the same. Active and passive stall margin improvement methods mainly target the tip leakage vortex. In the current study, numerical investigations are carried out to understand flow fields near tip region of rotors. The blade tip designed to have a tip gap as sine and cosine waves (single and double waves). Numerical methodology is validated with NASA Rotor37 test results. The performance parameters of the rotors with modified tip gap shapes are compared with constant tip clearance rotor. A detailed flow field investigation is presented to compare the tip flow structure and its impact on overall performance of the compressor.

Numerical Simulation of Tip Clearance Control in Axial Turbine Rotor: Part 2—Passive Control of Five Different Tip Platforms

2008 ◽  
Author(s):  
Wei Li ◽  
Wei-Yang Qiao ◽  
Kai-Fu Xu ◽  
Hua-Ling Luo
Keyword(s):  
Flow Control ◽  
Passive Control ◽  
Suction Side ◽  
Turbine Rotor ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Clearance Flow

The tip leakage flow has significant effects on turbine in loss production, aerodynamic efficiency, etc. Then it’s important to minimize these effects for a better performance by adopting corresponding flow control. The active turbine tip clearance flow control with injection from the tip platform is given in Part-1 of this paper. This paper is Part-2 of the two-part papers focusing on the effect of five different passive turbine tip clearance flow control methods on the tip clearance flow physics, which consists of a partial suction side squealer tip (Partial SS Squealer), a double squealer tip (Double Side Squealer), a pressure side tip shelf with inclined squealer tip on a double squealer tip (Improved PS Squealer), a tip platform extension edge in pressure side (PS Extension) and in suction side (SS Extension) respectively. Combined with the turbine rotor and the numerical method mentioned in Part 1, the effects of passive turbine tip clearance flow controls on the tip clearance flow were sequentially simulated. The detailed tip clearance flow fields with different squealer rims were described with the streamline and the velocity vector in various planes parallel to the tip platform or normal to the tip leakage vortex core. Accordingly, the mechanisms of five passive controls were put in evidence; the effects of the passive controls on the turbine efficiency and the tip clearance flow field were highlighted. The results show that the secondary flow loss near the outer casing including the tip leakage flow and the casing boundary layer can be reduced in all the five passive control methods. Comparing the active control with the passive control, the effect brought by the active injection control on the tip leakage flow is evident. The turbine rotor efficiency could be increased via the rational passive turbine tip clearance flow control. The Improved PS Squealer had the best effect on turbine rotor efficiency, and it increased by 0.215%.

Tip Leakage Flows Near Partial Squealer Rims in an Axial Flow Turbine Stage

2003 ◽  
Author(s):  
Cengiz Camci ◽  
Debashis Dey ◽  
Levent Kavurmacioglu
Keyword(s):  
Total Pressure ◽  
Axial Flow ◽  
Suction Side ◽  
Leakage Flow ◽  
Pressure Side ◽  
Turbine Stage ◽  
Tip Leakage Flow ◽  
Edge Zone ◽  
Tip Leakage ◽  
Partial Length

This paper deals with an experimental investigation of aerodynamic characteristics of full and partial-length squealer rims in a turbine stage. Full and partial-length squealer rims are investigated separately on the pressure side and on the suction side in the “Axial Flow Turbine Research Facility” (AFTRF) of the Pennsylvania State University. The streamwise length of these “partial squealer tips” and their chordwise position are varied to find an optimal aerodynamic tip configuration. The optimal configuration in this cold turbine study is defined as the one that is minimizing the stage exit total pressure defect in the tip vortex dominated zone. A new “channel arrangement” diverting some of the leakage flow into the trailing edge zone is also studied. Current results indicate that the use of “partial squealer rims” in axial flow turbines can positively affect the local aerodynamic field by weakening the tip leakage vortex. Results also show that the suction side partial squealers are aerodynamically superior to the pressure side squealers and the channel arrangement. The suction side partial squealers are capable of reducing the stage exit total pressure defect associated with the tip leakage flow to a significant degree.

Aerodynamic Interaction Between Incoming Vortex and Tip Leakage Flow in a Turbine Cascade

2018 ◽  
Author(s):  
Kai Zhou ◽  
Chao Zhou
Keyword(s):  
Numerical Study ◽  
Aerodynamic Performance ◽  
Leakage Flow ◽  
Computational Domain ◽  
Turbine Cascade ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Swirl Generator ◽  
Swirling Vortex

In turbines, secondary vortices and tip leakage vortices develop and interact with each other. In order to understand the flow physics of vortices interaction, the effects of incoming vortex on the downstream tip leakage flow are investigated in terms of the aerodynamic performance in a turbine cascade. Experimental, numerical and analytical methods are used. In the experiment, a swirl generator was used upstream near the casing to generate the incoming vortex, which interacted with the tip leakage vortex in the turbine cascade. The swirl generator was located at ten different pitchwise locations to simulate the quasi-steady effects. In the numerical study, a Rankine-like vortex was defined at the inlet of the computational domain to simulate the incoming swirling vortex. Incoming vortices with opposite directions were investigated. The vorticity of the positive incoming swirling vortex has a large vector in the same direction as that of the tip leakage vortex. In the case of the positive incoming swirling vortex, the vortex mixes with the tip leakage vortex to form one vortex near the tip as it transports downstream. The vortices interaction reduces the vorticity of the flow near the tip, as well as the loss by making up for the streamwise momentum within the tip leakage vortex core. In contrast, the negative incoming swirling vortex has little effects on the tip leakage vortex and the loss. As the negative incoming swirling vortex transports downstream, it is separated from the tip leakage vortex and forms two vortices. A triple-vortices-interaction kinetic analytical model and one-dimensional mixing model are proposed to explain the mechanism of vortex interaction on the aerodynamic performance.

Sign in / Sign up

Export Citation Format

Share Document