Dynamic Analysis of Large Specialty Glass Panels Under Ball Drop Impact — Numerical Modeling and Measurements

2012 ◽  
Author(s):  
Satish C. Chaparala ◽  
Praveen R. Samala ◽  
Joshua M. Jacobs ◽  
Jonathan D. Pesansky
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Impact Energy ◽  
Consumer Electronics ◽  
Impact Loads ◽  
Cover Glass ◽  
Element Analysis ◽  
Glass Panels ◽  
Alumino Silicate ◽  
The Impact

Response of brittle plate-like structures to impact loads (suddenly applied loads) has been the subject of many research studies. Specifically, glass used in various household, consumer electronics applications can be subjected to different kinds of impact loads. An ion-exchanged alumino-silicate glass developed by Corning Incorporated, also called Corning® Gorilla® Glass is used as cover glass for flat-panel televisions. One of the reliability tests that may be required for this application is that a steel ball of certain diameter is dropped from certain height at different locations on the glass panel mounted onto a frame. The requirement is that the glass should survive 2 J of impact energy at the center of the glass and 0.5 J of impact energy at the edges. These reliability requirements could change depending on the application and the customer. In this study, finite element analysis is carried out to understand the impact response of such glass panels. Experiments are conducted using strain gauges to measure the panel response at the center of glass with impacts up to 3.3 J. Finite element analysis results are then validated by comparing the predicted strain response with those of measurements.

scholarly journals Finite Element Analysis of Impact Energy on Spur Gear

2018 ◽  
Vol 225 ◽  
pp. 06011 ◽  
Author(s):  
Ismail Ali Bin Abdul Aziz ◽  
Daing Mohamad Nafiz Bin Daing Idris ◽  
Mohd Hasnun Arif Bin Hassan ◽  
Mohamad Firdaus Bin Basrawi
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Impact Energy ◽  
High Speed ◽  
Impact Test ◽  
Impact Load ◽  
Gear Tooth ◽  
Test Equipment ◽  
Element Analysis ◽  
The Impact

In high-speed gear drive and power transmission, system impact failure mode always occurs due to the sudden impact and shock loading during the system in running. Therefore, study on the amount of impact energy that can be absorbed by a gear is vital. Impact test equipment has been designed and modelled for the purpose to study the impact energy on gear tooth. This paper mainly focused on Finite Element Analysis (FEA) of impact energy that occurred during simulation involving the impact test equipment modelling. The simulation was conducted using Abaqus software on critical parts of the test equipment to simulate the impact event and generate impact data for analysis. The load cell in the model was assumed to be free fall at a certain height which gives impact load to the test gear. Three different type of material for the test gear were set up in this simulation. Results from the simulation show that each material possesses different impact energy characteristic. Impact energy values increased along with the height of load drop. AISI 1040 were found to be the toughest material at 3.0m drop that could withstand up to 44.87N.m of impact energy. These data will be used to validate data in physical experiments in further study.

Response of Dolos Concrete Armor Units to Impact Loads

1991 ◽  
Vol 113 (4) ◽  
pp. 286-291 ◽  
Author(s):  
J. W. Tedesco ◽  
P. B. McGill ◽  
W. G. McDougal
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Material Properties ◽  
Concrete Strength ◽  
Impact Resistance ◽  
Nonlinear Material ◽  
Impact Loads ◽  
Model Formulation ◽  
Element Analysis ◽  
The Impact

A finite element analysis is conducted to determine the critical impact velocities for concrete dolos. The model formulation includes deformations at the contact surface and nonlinear material properties. Two dolos orientations are considered: vertical fluke seaward and horizontal fluke seaward. In both cases, the larger units fail at lower angular impact velocities. It is also shown that doubling the concrete strength increases the impact resistance by approximately 40 percent.

Simplified Method for Predicting Impact Loads of Solid-Walled Transportation Packagings for Radioactive Materials

1989 ◽  
Vol 111 (3) ◽  
pp. 316-321 ◽  
Author(s):  
W. W. Teper ◽  
R. G. Sauve´
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Impact Analysis ◽  
Impact Force ◽  
Impact Loads ◽  
Radioactive Materials ◽  
Element Analysis ◽  
Elastic Plastic ◽  
The Impact ◽  
Good Agreement

Transportation packagings for radioactive materials must withstand severe impact conditions without loss of integrity and without excessive permanent distortions in the seal regions. The compliance with the requirements may be shown either through extensive testing, elastic-plastic impact analysis, or a combination of both. Elastic-plastic finite element analysis, although less costly than testing, is usually expensive and time consuming. In this paper, simplified methods for determining the impact force are presented for the following impact cases of solid-walled casks: impact on a pin, impact on an edge, and impact on a corner. The results of the simplified methods are in good agreement with the results of elastic-plastic finite element analysis. It is shown that in each case almost the entire impact energy is dissipated by the plastic deformation of the material in the impact zone.

Experimental and numerical comparisons of ballistic impact behaviors between 3D angle-interlock woven fabric and its reinforced composite

2018 ◽  
Vol 48 (6) ◽  
pp. 1044-1058 ◽  
Author(s):  
Pibo Ma ◽  
Limin Jin ◽  
Liwei Wu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Impact Energy ◽  
Three Dimensional ◽  
Ballistic Impact ◽  
Woven Fabric ◽  
Woven Composite ◽  
Element Analysis ◽  
Reinforced Composite ◽  
The Impact

This paper compares the ballistic impact damage behaviors between the three-dimensional angle-interlock woven fabric and its reinforced composite (three-dimensional angle interlock woven composite) under various ballistic strike velocities based on experimental and numerical finite element analysis. In experiments, the residual velocities of projectiles were recorded to compare their ballistic proof properties undergoing different impact loading conditions. Furthermore, the ultimate damage morphologies of both types of materials were also compared to deduce the specific ballistic impact performance and energy absorption mechanisms between the three-dimensional angle interlock woven fabric and three-dimensional angle interlock woven composite. It was found that the three-dimensional angle interlock woven composite has absorbed more energy than the three-dimensional angle interlock woven fabric under the “high” ballistic velocities (higher than 350 m/s). And it shows the opposite phenomena under the “low” ballistic velocities (lower than 350 m/s). In finite element analysis, the simplified finite element models were established for both materials to characterize the critical importance of resin matrix in transferring and dissipating the high velocity impact energy. Especially for three-dimensional angle interlock woven composite, the impact energy was transferred to the large area during a relatively short period of time, thereby resulting in an overall bearing capacity of the composite structure, therefore absorbed most of the impact energy, which was well applied to explain the experimental results.

Response of Mild Steel Pipes Under High Mass Low Velocity Impacts

2014 ◽  
Author(s):  
Shamsoon Fareed ◽  
Ian May
Keyword(s):  
Finite Element ◽  
Mild Steel ◽  
Impact Energy ◽  
High Mass ◽  
Low Velocity ◽  
Element Analysis ◽  
Steel Pipes ◽  
Impact Tests ◽  
The Finite Element Analysis ◽  
The Impact

Accidental loads, for example, due to heavy dropped objects, impact from the trawl gear and anchors of fishing vessels can cause damage to pipelines on the sea bed. The amount of damage will depend on the impact energy. The indentation will be localized at the contact area of the pipe and the impacting object, however, an understanding of the extent of the damage due to an impact is required so that if one should occur in practice an assessment can be made to determine if remedial action needs to be taken to ensure that the pipeline is still serviceable. There are a number of parameters, including the pipe cross section and impact energy, which influence the impact behaviour of a pipe. This paper describes the response, and assesses the damage, of mild steel pipes under high mass low velocity impacts. For this purpose full scale impacts tests were carried out on mild steel pipe having diameter of 457 mm, thickness of 25.4 mm and length of 2000 mm. The pipe was restrained along the base and a 2 tonnes mass with sharp impactor having a vertical downward velocity of 3870 mm/sec was used to impact the pipe transversely with an impact energy of 16 kJ. It was found from the impact tests that a smooth indentation was produced in the pipe. The impact tests were then used for validation of the non-linear dynamic implicit analyses using the finite element analysis software ABAQUS. Deformations at the impact zone, the rebound velocity, etc, recorded in the tests and the results of the finite element analysis were found to be in good agreement. The impact tests and finite element analyses described in this paper will help to improve the understanding of the response of steel pipes under impact loading and can be used as a benchmark for further finite element modelling of impacts on pipes.

Flexible Flowline Walking Tendency on Seabed With Longitudinal Undulations and Transverse Gradients

2018 ◽  
Author(s):  
Graeme Roberts ◽  
T. Sriskandarajah ◽  
Gianluca Colonnelli ◽  
Arnaud Roux ◽  
Alan Roy ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Temperature Gradients ◽  
Radius Of Curvature ◽  
Bend Radius ◽  
Lateral Buckling ◽  
Element Analysis ◽  
Slip Tendency ◽  
Start Ups ◽  
The Impact

A method of carrying out a combined axial walking and lateral buckling assessment for a flexible flowline has been developed using finite element analysis. The method overcomes limitations of screening assessments which could be inconclusive when applied either to a flexible flowline on an undulating seabed with transverse gradients or to one that buckles during hydrotest. Flexible flowlines that were to be surface-laid on a seabed with longitudinal undulations and transverse gradients were assessed using the method. The flexible flowlines were simulated in their as-laid state, and the simulation incorporated hydrotest pressure and the pressure & temperature gradients and transients associated with multiple start-ups. The objective was to quantify the axial walking and lateral slip tendency of the flexible flowlines and the impact that walking might have on the connected end structures. The lateral buckle locations predicted by finite element analysis were compared to a post-hydrotest survey and the radius of curvature from analysis was compared to the minimum bend radius of the flexible.

scholarly journals Finite Element Analysis-Aided Performance Improvement of Circular Coil Assemblies Applied in Electric Vehicle Inductive Chargers

2021 ◽  
Author(s):  
Guodong Zhu ◽  
Dawei Gao
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Electric Vehicle ◽  
Performance Improvement ◽  
Magnetic Circuit ◽  
Element Analysis ◽  
System Parameters ◽  
Leakage Magnetic Field ◽  
Fea Simulation ◽  
The Impact

Energy efficiency and leakage magnetic field (LMF) are two important issues in inductive chargers. In this work, the maximum achievable coil efficiency and the corresponding LMF strength are formulated as functions of system parameters, and figure of merits (FOM) are proposed for assessing the efficiency and LMF performance of the coil assemblies. The target application is electric vehicle inductive chargers where the LMF is suppressed via passive shielding. The impact of the coil assembly’s geometric parameters on both FOMs is examined through a combination of finite element analysis (FEA) simulation and magnetic circuit analysis, and measures to improve the FOMs are studied Optimization of an exemplary coil assembly within given dimensional limits is conducted and the performance improvement is verified by FEA simulation results. <br>

scholarly journals Simulation and Analysis of Fluid-Solid Coupling of Wave Impact Sandcastle Based on COMSOL

2020 ◽  
Vol 3 (1) ◽  
Author(s):  
Zhen Ouyang ◽  
Ke Wang ◽  
Zihao Yu ◽  
Kaikai Xu ◽  
Qianyu Zhao ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Simulation Analysis ◽  
Coupling Model ◽  
Complex Problem ◽  
Wave Impact ◽  
Element Analysis ◽  
Quantitative Calculation ◽  
The Finite Element Analysis ◽  
The Impact

It is a complex problem to study the interaction between sand castle and flowing water, which needs to consider the complexity of seawater flow and the stress of sand castle structure. The authors use the fluid-solid coupling model to establish the connection between the fluid field and the structural mechanical field, and use the finite element analysis to complete the simulation modeling of the transient process of wave impact and sandcastle foundation deformation. This paper analyzes the stress and the first principal strain of the sand castle foundation in the direction of flow velocity when the sand castle foundation is hit by waves, as a method to judge the strength of the sand castle.The best shape: the boundary value of sand castle collapse caused by strain have been determined, so as to obtain the maximum stress that a sand castle foundation can bear before collapse, which makes it possible to use the fatigue strength calculation theory of sand castle solid to carry out the quantitative calculation of sand castle durability. At the same time, the impact of waves is abstracted as wave motion equation. Finally, the finite element analysis technology is adopted to calculate the main strain of sandcastles of different shapes under the impact of the same wave, and through the comparison of the main strain, the authors get the sandcastle shape with the strongest anti-wave impact ability, which is the eccentric circular platform body.Affected by rain: the authors considered the effect of rainwater infiltration on the sandcastle's stress, and simplified the process of rain as a continuous and uniform infiltration of rain into the sandcastle's surface. The rain changes the gravity of the sand on the castle's surface. Simulation analysis is adopted to calculate the surface stress of sand castle with different degree of water seepage and different geometry. By comparison, it has been found that the smooth cone is more able to withstand the infiltration of rain without collapse. 

Finite Element Analysis for Shock Resistance Evaluation of Cushion-Packaged Multifunction Printer Considering Internal Modules

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Se-Chang Kim ◽  
Dae-Geun Cho ◽  
Tae-Gyu Kim ◽  
Se-Hun Jung ◽  
Ja-Choon Koo ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Shock Acceleration ◽  
External Shocks ◽  
Compression Tests ◽  
Element Analysis ◽  
Dynamic Behaviors ◽  
Shock Resistance ◽  
The Impact ◽  
Multifunction Printer

Failures in IT electronics are often caused by falling or external shocks during transportation. These failures cause customers to mistrust the reliability of the products. Many manufacturers of IT electronics have not only used cushioning materials but also increased the shock resistance of their products for failure prevention. Especially in case of printer products, the design of the packaging and the product robustness are extremely important because of their substantial weight and the fragility of the internal modules. For product design, it is essential to understand the impact failure mechanism of the products. In this study, a compression test, a drop impact test, and a finite element analysis (FEA) were performed to analyze the dynamic behaviors of a packaged multifunction printer (MFP). The mechanical properties of a cushioning material were measured by compression tests. The FE models of the cushion packaging and the MFP included the physical characteristics of the internal modules, and their dynamic behaviors were obtained using the commercial software ls-dyna3d. Simulation results were also compared with drop test results to verify the proposed FE models. The shock resistance of the MFP was assessed by stress analysis and strength evaluation. We also expect our FE models will be useful for evaluating the fragility of the internal modules because the models can numerically estimate the shock acceleration profiles of the internal modules, which are difficult to measure experimentally.

Sign in / Sign up

Export Citation Format

Share Document