Thermal-Mechanical Response of Non-Uniformly Heated Nominally Flat and Curved LEU Foil Based Target

2012 ◽  
Author(s):  
Kyler K. Turner ◽  
Gary L. Solbrekken ◽  
Charlie W. Allen
Keyword(s):  
Mechanical Response ◽  
Three Dimensional ◽  
Department Of Energy ◽  
Transfer Coefficients ◽  
Technetium 99M ◽  
Plate Design ◽  
Enriched Uranium ◽  
Aluminum Plates ◽  
Sandwiched Structure ◽  
Global Threat

Technetium-99m is a radiopharmaceutical currently used in 85% of all diagnostic imaging procedures. The relative long lived parent isotope of technetium-99m is molybdenum-99, which is commonly produced by irradiating highly enriched uranium. In accordance with the Department of Energy: National Nuclear Security Administration’s Global Threat Reduction Initiative an effort is underway to develop low enriched uranium based molybdenum-99 production concepts. Achieving comparable molybdenum-99 yields in a low enriched uranium target effectively mandates the use of a high density metal low enriched uranium foil. Using a foil requires a significant modification to the current highly enriched uranium dispersion target designs. One design concept uses a low enriched uranium foil sandwiched between either two flat or curved aluminum plates. The low enriched uranium is enclosed in the sandwiched structure by welding the aluminum plates together about their edges. The plate design is inspired by low enriched uranium fuel plates with the exception that the low enriched uranium is not bonded to the aluminum plates nor is it necessary to clamp the plate edges to prevent lateral translation. The lack of bonding between the low enriched uranium foil and the plates allows easy removal of the foil after irradiation for chemically processing and separation. The un-heated edges of the plate target produce three-dimensional temperature gradients inducing deformations and stress. This paper will review the thermal mechanical response of a low enriched uranium foil based molybdenum-99 production target. This study describes the effect of various curvatures, thermal loads, and heat transfer coefficients on the thermal-induced deflection and stress.

Thermal-Mechanical Response of Non-Uniformly Heated LEU Foil Based Target

2011 ◽  
Author(s):  
Kyler K. Turner ◽  
Gary L. Solbrekken ◽  
Charlie W. Allen
Keyword(s):  
Mechanical Response ◽  
Metal Foil ◽  
Transfer Coefficients ◽  
Technetium 99M ◽  
Heat Transfer Coefficients ◽  
Plate Design ◽  
Enriched Uranium ◽  
Aluminum Plates ◽  
Sandwiched Structure ◽  
Global Threat

Technetium-99m is a diagnostic radiopharmaceutical that is currently used in 80% of the global nuclear diagnostic imaging procedures. The parent isotope for technetium-99m is molybdenum-99, most commonly obtained through the irradiation of high enriched uranium (HEU) targets. In accordance with the Department of Energy’s Global Threat Reduction Initiative (GTRI) an effort is underway to develop a process to produce molybdenum-99 using low enriched uranium (LEU) targets to maintain production yield relative to HEU targets. Conversion of targets to LEU material effectively mandates that the most efficient process is to cast LEU in the form of a metal foil as opposed to current powder based dispersion designs for HEU. Using a foil requires a significant modification to the current target design. One design concept uses an LEU foil sandwiched between two nominally flat aluminum plates. The LEU is enclosed in the sandwiched structure by welding the aluminum plates together about their edges. The plate design is inspired by high density monolithic LEU fuel plates with the exception that the LEU is not bonded to the aluminum plates nor is it necessary to clamp the plate edges to prevent lateral translation. The lack of bonding between the LEU foil and the plates allows the edges of the plate to be cut off so the foil can be removed after irradiation to be chemically processed. The un-heated edges of the plate target produce 3-D temperature gradients that induce plate deformations. This paper will review thermal mechanical response of an LEU foil based molybdenum-99 plate target geometry. This study describes the effect of various edge holding conditions, thermal loads, and heat transfer coefficients on the thermal-induced deflection and stress in the plates.

Construction of plastic contact deformation maps on ceramics: a case study on aluminum nitride

1996 ◽  
Vol 54 ◽  
pp. 636-637
Author(s):  
D. L. Callahan
Keyword(s):  
Plastic Deformation ◽  
Aluminum Nitride ◽  
Mechanical Response ◽  
Three Dimensional ◽  
Bright Field Image ◽  
Perfectly Plastic ◽  
Contrast Analysis ◽  
Deformation Patterns

Modern polishing, precision machining and microindentation techniques allow the processing and mechanical characterization of ceramics at nanometric scales and within entirely plastic deformation regimes. The mechanical response of most ceramics to such highly constrained contact is not predictable from macroscopic properties and the microstructural deformation patterns have proven difficult to characterize by the application of any individual technique. In this study, TEM techniques of contrast analysis and CBED are combined with stereographic analysis to construct a three-dimensional microstructure deformation map of the surface of a perfectly plastic microindentation on macroscopically brittle aluminum nitride.The bright field image in Figure 1 shows a lg Vickers microindentation contained within a single AlN grain far from any boundaries. High densities of dislocations are evident, particularly near facet edges but are not individually resolvable. The prominent bend contours also indicate the severity of plastic deformation. Figure 2 is a selected area diffraction pattern covering the entire indentation area.

scholarly journals D936Y and Other Mutations in the Fusion Core of the SARS-CoV-2 Spike Protein Heptad Repeat 1: Frequency, Geographical Distribution, and Structural Effect

Molecules ◽  
2021 ◽  
Vol 26 (9) ◽  
pp. 2622
Author(s):  
Romina Oliva ◽  
Abdul Rajjak Shaikh ◽  
Andrea Petta ◽  
Anna Vangone ◽  
Luigi Cavallo
Keyword(s):  
Three Dimensional ◽  
Salt Bridge ◽  
Structural Effect ◽  
Host Cells ◽  
Heptad Repeat ◽  
Genomic Sequences ◽  
Strong Interactions ◽  
Virus Infectivity ◽  
S Protein ◽  
Global Threat

The crown of the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is constituted by its spike (S) glycoprotein. S protein mediates the SARS-CoV-2 entry into the host cells. The “fusion core” of the heptad repeat 1 (HR1) on S plays a crucial role in the virus infectivity, as it is part of a key membrane fusion architecture. While SARS-CoV-2 was becoming a global threat, scientists have been accumulating data on the virus at an impressive pace, both in terms of genomic sequences and of three-dimensional structures. On 15 February 2021, from the SARS-CoV-2 genomic sequences in the GISAID resource, we collected 415,673 complete S protein sequences and identified all the mutations occurring in the HR1 fusion core. This is a 21-residue segment, which, in the post-fusion conformation of the protein, gives many strong interactions with the heptad repeat 2, bringing viral and cellular membranes in proximity for fusion. We investigated the frequency and structural effect of novel mutations accumulated over time in such a crucial region for the virus infectivity. Three mutations were quite frequent, occurring in over 0.1% of the total sequences. These were S929T, D936Y, and S949F, all in the N-terminal half of the HR1 fusion core segment and particularly spread in Europe and USA. The most frequent of them, D936Y, was present in 17% of sequences from Finland and 12% of sequences from Sweden. In the post-fusion conformation of the unmutated S protein, D936 is involved in an inter-monomer salt bridge with R1185. We investigated the effect of the D936Y mutation on the pre-fusion and post-fusion state of the protein by using molecular dynamics, showing how it especially affects the latter one.

scholarly journals Numerical simulation of variable thermal conductivity on 3D flow of nanofluid over a stretching sheet

2020 ◽  
Vol 9 (1) ◽  
pp. 233-243 ◽  
Author(s):  
Nainaru Tarakaramu ◽  
P.V. Satya Narayana ◽  
Bhumarapu Venkateswarlu
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Stretching Sheet ◽  
Three Dimensional ◽  
Variable Thermal Conductivity ◽  
Normal Velocity ◽  
Transfer Coefficients ◽  
Similarity Transformations ◽  
Frictional Coefficients ◽  
The Impact

AbstractThe present investigation deals with the steady three-dimensional flow and heat transfer of nanofluids due to stretching sheet in the presence of magnetic field and heat source. Three types of water based nanoparticles namely, copper (Cu), aluminium oxide (Al2O3), and titanium dioxide (TiO2) are considered in this study. The temperature dependent variable thermal conductivity and thermal radiation has been introduced in the energy equation. Using suitable similarity transformations the dimensional non-linear expressions are converted into dimensionless system and are then solved numerically by Runge-Kutta-Fehlberg scheme along with well-known shooting technique. The impact of various flow parameters on axial and transverse velocities, temperature, surface frictional coefficients and rate of heat transfer coefficients are visualized both in qualitative and quantitative manners in the vicinity of stretching sheet. The results reviled that the temperature and velocity of the fluid rise with increasing values of variable thermal conductivity parameter. Also, the temperature and normal velocity of the fluid in case of Cu-water nanoparticles is more than that of Al2O3- water nanofluid. On the other hand, the axial velocity of the fluid in case of Al2O3- water nanofluid is more than that of TiO2nanoparticles. In addition, the current outcomes are matched with the previously published consequences and initiate to be a good contract as a limiting sense.

Flow Past a Spinning Sphere With Surface Blowing and Heat Transfer

2005 ◽  
Vol 127 (1) ◽  
pp. 163-171 ◽  
Author(s):  
H. Niazmand ◽  
M. Renksizbulut
Keyword(s):  
Heat Transfer ◽  
Three Dimensional ◽  
Flow Regimes ◽  
Solid Sphere ◽  
Temporal Variations ◽  
Transfer Coefficients ◽  
Transfer Rates ◽  
Particle Spin ◽  
Flow Past ◽  
Angular Velocities

Computations are performed to determine the transient three-dimensional heat transfer rates and fluid forces acting on a stream-wise spinning sphere for Reynolds numbers in the range 10⩽Re⩽300 and angular velocities Ωx⩽2. In this Re range, classical flow past a solid sphere develops four different flow regimes, and the effects of particle spin are studied in each regime. Furthermore, the combined effects of particle spin and surface blowing are examined. Sphere spin increases drag in all flow regimes, while lift shows a nonmonotonic behavior. Heat transfer rates are not influenced by spin up to a certain Ωx but increase monotonically thereafter. An interesting feature associated with sphere spin is the development of a special wake regime such that the wake simply spins without temporal variations in its shape. For this flow condition, the magnitudes of the lift, drag, and heat transfer coefficients remain constant in time. Correlations are provided for drag and heat transfer.

Study on Stress and Strain of Anchorage Using Finite Element Method

2013 ◽  
Vol 325-326 ◽  
pp. 1314-1317
Author(s):  
Cong Sheng Chen ◽  
Ping He ◽  
Cheng Yong Wang ◽  
Xue Hui Chen ◽  
Lei Huang ◽  
...  
Keyword(s):  
Finite Element ◽  
Strain Distribution ◽  
Maximum Stress ◽  
Mechanical Response ◽  
Three Dimensional ◽  
Integrated Modeling ◽  
Stress And Strain ◽  
Steel Strand ◽  
Prestressed State ◽  
Stress And Strain Distribution

Three-dimensional integrated modeling method and the numerical simulation of elastoplastic finite element are adopted in the paper. The mechanical response of the five holes anchorage is analyzed in certain prestressed state. The stress and strain distribution information of the anchor ring, clip and steel strand is obtained respectively, and the structure safety is discussed by investigating on the maximum stress and strain.

Computational Insights Into Air-Side Flow and Heat Transfer in Compact Heat Exchangers

2005 ◽  
Author(s):  
D. K. Tafti
Keyword(s):  
Heat Transfer ◽  
Heat Capacity ◽  
Heat Exchangers ◽  
Three Dimensional ◽  
Computer Experiments ◽  
Transfer Coefficients ◽  
Substantial Impact ◽  
Compact Heat Exchangers ◽  
Thermal Phenomena ◽  
Side Flow

The paper describes two- and three-dimensional computer simulations which are used to study fundamental flow and thermal phenomena in multilouvered fins used for air-side heat transfer enhancement in compact heat exchangers. Results pertaining to flow transition, thermal wake interference, and fintube junction effects are presented. It is shown that a Reynolds number based on flow path rather than louver pitch is more appropriate in defining the onset of transition, and characteristic frequencies in the louver bank scale better with a global length scale such as fin pitch than with louver pitch or thickness. With the aid of computer experiments, the effect of thermal wakes is quantified on the heat capacity of the fin as well as the heat transfer coefficient, and it is established that experiments which neglect accounting for thermal wakes can introduce large errors in the measurement of heat transfer coefficients. Further, it is shown that the geometry of the louver in the vicinity of the tube surface has a large effect on tube heat transfer and can have a substantial impact on the overall heat capacity.

Experimental Characterization and Finite Element Modeling of Film Capacitors for Automotive Applications

2016 ◽  
Author(s):  
D. Croccolo ◽  
T. M. Brugo ◽  
M. De Agostinis ◽  
S. Fini ◽  
G. Olmi
Keyword(s):  
Finite Element ◽  
Mechanical Response ◽  
High Reliability ◽  
Three Dimensional ◽  
Strain Analysis ◽  
Life Time ◽  
Element Model ◽  
Image Correlation ◽  
Thermal Loads ◽  
Mechanical Shock

As electronics keeps on its trend towards miniaturization, increased functionality and connectivity, the need for improved reliability capacitors is growing rapidly in several industrial compartments, such as automotive, medical, aerospace and military. Particularly, recent developments of the automotive compartment, mostly due to changes in standards and regulations, are challenging the capabilities of capacitors in general, and especially film capacitors. Among the required features for a modern capacitor are the following: (i) high reliability under mechanical shock, (ii) wide working temperature range, (iii) high insulation resistance, (iv) small dimensions, (v) long expected life time and (vi) high peak withstanding voltage. This work aims at analyzing the key features that characterize the mechanical response of the capacitor towards temperature changes. Firstly, all the key components of the capacitor have been characterized, in terms of strength and stiffness, as a function of temperature. These objectives have been accomplished by means of several strain analysis methods, such as strain gauges, digital image correlation (DIC) or dynamic mechanical analysis (DMA). All the materials used to manufacture the capacitor, have been characterized, at least, with respect to their Young’s modulus and Poisson’s ratio. Then, a three-dimensional finite element model of the whole capacitor has been set up using the ANSYS code. Based on all the previously collected rehological data, the numerical model allowed to simulate the response in terms of stress and strain of each of the capacitor components when a steady state thermal load is applied. Due to noticeable differences between the thermal expansion coefficients of the capacitor components, stresses and strains build up, especially at the interface between different components, when thermal loads are applied to the assembly. Therefore, the final aim of these numerical analyses is to allow the design engineer to define structural optimization strategies, aimed at reducing the mechanical stresses on the capacitor components when thermal loads are applied.

The Effect of Trabecular Bone on the Mechanical Response of Human Mandible with Implant

2014 ◽  
Vol 695 ◽  
pp. 588-591
Author(s):  
Khairul Salleh Basaruddin ◽  
Ruslizam Daud
Keyword(s):  
Computed Tomography ◽  
Finite Element ◽  
Trabecular Bone ◽  
Static Analysis ◽  
Load Distribution ◽  
Mechanical Response ◽  
Three Dimensional ◽  
Fe Model ◽  
Micro Computed Tomography ◽  
Bone Specimen

This study aims to investigate the influence of trabecular bone in human mandible bone on the mechanical response under implant load. Three dimensional voxel finite element (FE) model of mandible bone was reconstructed from micro-computed tomography (CT) images that were captured from bone specimen. Two FE models were developed where the first consists of cortical bone, trabecular bone and implants, and trabecular bone part was excluded in the second model. A static analysis was conducted on both models using commercial software Voxelcon. The results suggest that trabecular bone contributed to the strength of human mandible bone and to the effectiveness of load distribution under implant load.

Sign in / Sign up

Export Citation Format

Share Document