scholarly journals Characterization of In-Pipe Acoustic Wave for Water Leak Detection

Author(s):  
Atia E. Khalifa ◽  
Rached Ben-Mansour ◽  
Kamal Youcef-Toumi ◽  
Changrak Choi

This paper presents experimental observations on the characteristics of the acoustic signal propagation and attenuation inside water-filled pipes. An acoustic source (exciter) is mounted on the internal pipe wall, at a fixed location, and produces a tonal sound to simulate a leak noise with controlled frequency and amplitude, under different flow conditions. A hydrophone is aligned with the pipe centerline and can be re-positioned to capture the acoustic signal at different locations. Results showed that the wave attenuation depends on the source frequency and the line pressure. High frequency signals get attenuated more with increasing distance from the source. The optimum location to place the hydrophone for capturing the acoustic signal is not at the vicinity of source location. The optimum location also depends on the frequency and line pressure. It was also observed that the attenuation of the acoustic waves is higher in more flexible pipes like PVC ones.

1991 ◽  
Vol 69 (3-4) ◽  
pp. 461-464 ◽  
Author(s):  
F. Guillion ◽  
A. Sachrajda ◽  
M. D'Iorio ◽  
R. Boulet ◽  
P. Coleridge

We report simultaneous magnetotransport and surface acoustic-wave attenuation measurements performed at 1.25 K on a two-dimensional electron gas (2-DEG) GaAs–AlGaAs heterojunction sample. The carrier density was varied by means of the persistent photoconductivity effect. A comparison of the conductivity deduced from the two types of measurements is used to obtain information about the homogeneity of the 2-DEG sample. For this specific sample a simple model shows that there exists a 20% variation in the carrier density at some intermediate carrier densities, while prior to illumination and after saturation with light the spread in carrier density in the sample was only a few percent.


Author(s):  
Kemining W. Yeh ◽  
Richard S. Muller ◽  
Wei-Kuo Wu ◽  
Jack Washburn

Considerable and continuing interest has been shown in the thin film transducer fabrication for surface acoustic waves (SAW) in the past few years. Due to the high degree of miniaturization, compatibility with silicon integrated circuit technology, simplicity and ease of design, this new technology has played an important role in the design of new devices for communications and signal processing. Among the commonly used piezoelectric thin films, ZnO generally yields superior electromechanical properties and is expected to play a leading role in the development of SAW devices.


2020 ◽  
Vol 67 (1) ◽  
pp. 28-34
Author(s):  
Aleksandr V. Vinogradov ◽  
Aleksey V. Bukreev

When repairing and replacing electrical wiring in enterprises, the main difficulty is the lack or poor quality of documentation, plans for conductors laying. Distinguishing wires (cables) and their cores by the color of the shells or using tags attached to the ends is difficult if the shells have the same color and there are no tags. Devices and technical solutions used to identify wires and cables do not allow recognizing conductors without breaking the electrical circuit, removing insulation, and de-energizing the network. Searching for the right conductor is a time-consuming operation. (Research purpose) The research purpose is developing a new microcontroller device for identifying wires using an acoustic signal. (Materials and methods) Literature sources has been searched for devices for conductors identifying. (Results and discussion) The article proposes a method that involves feeding an acoustic signal to a wire at one point and capturing it at another, in order to recognize the desired wire. The article presents results of comparison of the developed microcontroller device for identifying conductors using an acoustic signal with known devices and methods for conductors recognizing. (Conclusions) The article reveals the shortcomings of existing methods and means of identifying wires and cables. Authors performed a theoretical calculation of the sound pressure in the conductor at a given distance. The article presents the calculation of speed of acoustic waves in conductors with different types of insulation. Authors designed a microcontroller device for identifying conductors using an acoustic signal and tested it. It was determined that the device increases the safety of work, reduces the cost of operating internal wiring and identification time; eliminates the violation of wire insulation, the need to disable electrical receivers. The convergence of theoretical calculations and experimental data was shown.


SIMULATION ◽  
2021 ◽  
pp. 003754972199645
Author(s):  
Philippe Babilotte

Complete numerical simulations are given under SciLab® and MATLAB® coding environments, concerning propagative acoustic wavefronts, for laser picosecond ultrasonics under multiwavelength conditions. Simulations of the deformation field and its propagation into bulk material are given under different wavelength configurations for optical pump and probe beams, which are used to generate and to detect the acoustic signal. Complete insights concerning the dynamics of the acoustic waves are given, considering the absence of carrier diffusions into the material. Several numerical approaches are proposed concerning both the functions introduced to simulate the wavefront ( Heaviside or error) and the coding approach (linear/vectorized/ Oriented Object Programming), under the pure thermo-elastic approach.


Proceedings ◽  
2018 ◽  
Vol 2 (13) ◽  
pp. 902 ◽  
Author(s):  
Aurelien Mazzamurro ◽  
Abdelkrim Talbi ◽  
Yannick Dusch ◽  
Omar Elmazria ◽  
Philippe Pernod ◽  
...  

Over the last decades, the use of Surface Acoustic Waves (SAW) has emerged as a promising technology in many applications such as filters, signal processing but also sensors. We report the fabrication and the characterization of a SAW delay line magnetic field sensor using uniaxial multi-layered 14×[TbCo2(3.7nm)/FeCo(4nm)] nanostructured thin film deposited on Y36° Lithium Niobate (Figure 1a). The sensor shows an interesting dependency to a tunable bias magnetic field with different orientations relative to the easy axis. The obtained results are well explained using an equivalent piezo-magnetic model described in a previous work.


2002 ◽  
Vol 227 (9) ◽  
pp. 724-752 ◽  
Author(s):  
Corrine Welt ◽  
Yisrael Sidis ◽  
Henry Keutmann ◽  
Alan Schneyer

It has been 70 years since the name inhibin was used to describe a gonadal factor that negatively regulated pituitary hormone secretion. The majority of this period was required to achieve purification and definitive characterization of inhibin, an event closely followed by identification and characterization of activin and follistatin (FS). In contrast, the last 15–20 years saw a virtual explosion of information regarding the biochemistry, physiology, and biosynthesis of these proteins, as well as identification of activin receptors, and a unique mechanism for FS action—the nearly irreversible binding and neutralization of activin. Many of these discoveries have been previously summarized; therefore, this review will cover the period from the mid 1990s to present, with particular emphasis on emerging themes and recent advances. As the field has matured, recent efforts have focused more on human studies, so the endocrinology of inhibin, activin, and FS in the human is summarized first. Another area receiving significant recent attention is local actions of activin and its regulation by both FS and inhibin. Because activin and FS are produced in many tissues, we chose to focus on a few particular examples with the most extensive experimental support, the pituitary and the developing follicle, although nonreproductive actions of activin and FS are also discussed. At the cellular level, it now seems that activin acts largely as an autocrine and/or paracrine growth factor, similar to other members of the transforming growh factor β superfamily. As we discuss in the next section, its actions are regulated extracellularly by both inhibin and FS. In the final section, intracellular mediators and modulators of activin signaling are reviewed in detail. Many of these are shared with other transforming growh factor β superfamily members as well as unrelated molecules, and in a number of cases, their physiological relevance to activin signal propagation remains to be elucidated. Nevertheless, taken together, recent findings suggest that it may be more appropriate to consider a new paradigm for inhibin, activin, and FS in which activin signaling is regulated extracellularly by both inhibin and FS whereas a number of intracellular proteins act to modulate cellular responses to these activin signals. It is therefore the balance between activin and all of its modulators, rather than the actions of any one component, that determines the final biological outcome. As technology and model systems become more sophisticated in the next few years, it should become possible to test this concept directly to more clearly define the role of activin, inhibin, and FS in reproductive physiology.


Author(s):  
Maria Maza ◽  
Fernando Lopez-Arias ◽  
Javier L. Lara ◽  
Inigo J. Losada

Estimation of the flow energy dissipation induced by an ecosystem that accounts for its characteristics (i.e. biomechanical properties, morphology, density) and the incident hydrodynamic conditions is crucial if ecosystem-based coastal protection measurements want to be implemented. Characterization of a vegetated ecosystem by measuring leaf traits, biomechanical properties of plants and the number of individuals per unit area involves a lot of effort and is case-specific. Standing biomass can be a unique variable defining the flow energy attenuation capacity of the ecosystem. To explore its relation to the induced energy attenuation on the flow, a new set of experiments using real vegetation with contrasting morphology and biomechanical properties, and subjected to different incident flow conditions is presented. The obtained standing biomass-attenuation relationships will help to quantify the expected coastal protection provided by different vegetated ecosystems based on their standing biomass and the flow conditions.Recorded Presentation from the vICCE (YouTube Link): https://youtu.be/-qaKkBWZApk


2021 ◽  
Vol 254 ◽  
pp. 02007
Author(s):  
Vladimir Korochentsev ◽  
Сhen Wenjian ◽  
Victor Petrosyants ◽  
Tatiana Lobova ◽  
Julia Shpak

A mathematical model for elastic wave propagation in an ice cover with uneven relief (hummock) has been developed. The theoretical model is based on the application of “directed” Green’s functions. We obtained numerical results for different distances between radiating and receiving antennas installed inside the ice layer and in water medium. An information-measuring system was created to investigate elastic acoustic waves along ice surface based on electo-hydraulic generator. Experiments of high-frequency acoustic signal propagation from electro-hydraulic generator in water-ice-air system were carried out. We illustrated the model validity for the investigation of hydroacoustic wave propagation in real ice conditions.


2000 ◽  
Vol 78 (9) ◽  
pp. 803-821 ◽  
Author(s):  
B O'Neill ◽  
R Gr. Maev

Although the fundamental equations for the propagation of elastic and acoustic waves in anisotropic materials have not changed in more than a 100 years, the last few decades have seen a surge in interest in the topic. Much of this interest stems from the growing need for characterization of an increasing number of exotic materials. The intent of this paper is to review, for the benefit of beginning researchers in acoustics and ultrasonics, the fundamental phenomena related to elastic wave propagation in anisotropic media. We also present the most common and interesting theoretical methods developed over the past 20 years to model bulk wave propagation in such media. The methods discussed include plane wave superpositions, ray asymptotic theory, paraxial beams, and Green's functions. More peripheral issues, including anisotropic effects combined with various other exotic effects, are dealt with in the bibliography. PACS No.: 43.90


2021 ◽  
Vol 7 (2) ◽  
pp. 605-608
Author(s):  
Robert Ott ◽  
Alper Ö Öner ◽  
Paul Hermann Bellé ◽  
Finja Borowski ◽  
Klaus-Peter Schmitz ◽  
...  

Abstract Mitral regurgitation (MR) is the second most frequent indication for heart valve surgery and catheter interventions. According to European and US-American guidelines, transcatheter mitral valve repair in general and transcatheter edge-to-edge repair (TEER) in particular may be considered as a treatment option for selected high-risk patients. However, the biomechanical impact of TEERdevices on the mitral valve (MV) has not yet been fully understood. To address this problem, a 3D-Fluid-Structure Interaction (FSI) framework utilizing non-linear Finite Element Analysis (FEA) for the MV apparatus and Smoothed Particle Hydrodynamics (SPH) for the pulsatile fluid flow was developed and validated against in vitro data. An artificial MV-model (MVM) with a prolapse in the A2-P2 region and a custom-made TEER device implanted in the A2-P2 region were used for the in vitro investigations. In accordance with ISO 5910, projected mitral orifice areas (PMOA), flow rates as well as atrial and ventricular pressures were measured under pulsatile flow conditions before and after TEER device implantation. For the FSI-model, the MVM geometry was reconstructed by means of microcomputed tomography in a quasi-stress-free configuration. Quasi-static tensile test data was utilized for the development of linear- and hyperelastic material models of the chordae tendineae and leaflets, respectively. The fluid flow was modelled assuming an incompressible, homogenous Newtonian behaviour. Time-varying in vitro transmitral pressure loading was applied as a boundary condition. In vitro investigations show that TEER device implantation in the A2-P2 region effectively reduces the regurgitation fraction (RF) from 55 % to 13 %. Moreover, the comparison of experimental and numerical data yields a deviation of 2.09 % for the RF and a deviation of 0.40 % and 6.47 % for the maximum and minimum PMOA, respectively. The developed FSI-framework is in good agreement with in vitro data and is therefore applicable for the characterization of the biomechanical impact of different TEER devices under pulsatile flow conditions.


Sign in / Sign up

Export Citation Format

Share Document