Experimental Investigation of High-Speed Rotating Heat Pipes

2003 ◽  
Author(s):  
F. Song ◽  
D. Home ◽  
T. Robinson ◽  
D. Ewing ◽  
C. Y. Ching
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
High Speed ◽  
Heat Pipes ◽  
Theoretical Models ◽  
Test Facility ◽  
Working Fluid ◽  
Steady State Heat ◽  
Steady State Heat Transfer ◽  
Pipe Geometry

The steady state heat transfer characteristics of high-speed rotating heat pipes were measured using a newly commissioned high-speed rotating heat pipe test facility. The performance of two cylindrical and two tapered rotating heat pipes with different fluid loadings were tested for rotational speeds of 2,000 to 4,000 RPM and heat transfer rates up to 0.6 kW. The measurements were used to characterize the effects of rotational speed, working fluid loading, and heat pipe geometry on the performance of rotating heat pipes. The results were compared to previous theoretical models. There is a general agreement between test results and predictions from a model that accounts for natural convection within the liquid film at the evaporator at high accelerations. However, some results indicate that the model is not yet accounting for all the physics in a high-speed rotating heat pipe.

scholarly journals The effect of operating parameters on the heat transfer in the heat pipe

2021 ◽  
Vol 2119 (1) ◽  
pp. 012088
Author(s):  
A. A. Litvintceva ◽  
N. I. Volkov ◽  
N. I. Vorogushina ◽  
V. A. Moskovskikh ◽  
V. V. Cheverda
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Pipe ◽  
Temperature Difference ◽  
Heat Pipes ◽  
Working Fluid ◽  
Operating Parameters ◽  
Temperature Stabilization ◽  
Ir Camera ◽  
Fluid Properties

Abstract Heat pipes are a good solution for temperature stabilization, for example, of microelectronics, because these kinds of systems are without any moving parts. Experimental research of the effect of operating parameters on the heat transfer in a cylindrical heat pipe has been conducted. The effect of the working fluid properties and the porous layer thickness on the heat flux and temperature difference in the heat pipe has been investigated. The temperature field of the heat pipe has been investigated using the IR-camera and K-type thermocouples. The data obtained by IR-camera and K-type thermocouples have been compared. It is demonstrated the power transferred from the evaporator to the condenser is a linear function of the temperature difference between them.

scholarly journals An investigation on effect of EDL on heat transfer of micro heat pipe with square and triangular cross section

2020 ◽  
Vol 21 (3) ◽  
pp. 309
Author(s):  
Maryam Fallah Abbasi ◽  
Hossein Shokouhmand ◽  
Morteza Khayat
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Double Layer ◽  
Electric Double Layer ◽  
Heat Pipes ◽  
The Body ◽  
Working Fluid ◽  
Two Phase ◽  
Micro Heat Pipe ◽  
Micro Heat Pipes

Electronic industries have always been trying to improve the efficiency of electronic devices with small dimensions through thermal management of this equipment, thus increasing the use of small thermal sinks. In this study micro heat pipes with triangular and square cross sections have been manufactured and tested. One of the main objectives is to obtain an understanding of micro heat pipes and their role in energy transmission with electrical double layer (EDL). Micro heat pipes are highly efficient heat transfer devices, which use the continuous evaporation/condensation of a suitable working fluid for two-phase heat transport in a closed system. Since the latent heat of vaporization is very large, heat pipes transport heat at small temperature difference, with high rates. Because of variety of advantage features these devices have found a number of applications both in space and terrestrial technologies. The theory of operation micro heat pipes with EDL is described and the micro heat pipe has been studied. The temperature distribution have achieved through five thermocouples installed on the body. Water and different solution mixture of water and ethanol have used to investigate effect of the electric double layer heat transfer. It was noticed that the electric double layer of ionized fluid has caused reduction of heat transfer.

Effects of Surface Coating of Nanoparticles on Thermal Performance of Open Loop Pulsating Heat Pipes

2012 ◽  
Author(s):  
Mehdi Taslimifar ◽  
Maziar Mohammadi ◽  
Ali Adibnia ◽  
Hossein Afshin ◽  
Mohammad Hassan Saidi ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Surface Coating ◽  
Heat Pipes ◽  
Open Loop ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Performance Of Heat Transfer

Homogenous dispersing of nanoparticles in a base fluid is an excellent way to increase the thermal performance of heat transfer devices especially Heat Pipes (HPs). As a wickless, cheap and efficient heat pipe, Pulsating Heat Pipes (PHPs) are important candidates for thermal application considerations. In the present research an Open Loop Pulsating Heat Pipe (OLPHP) is fabricated and tested experimentally. The effects of working fluid namely, water, Silica Coated ferrofluid (SC ferrofluid), and ferrofluid without surface coating of nanoparticles (ferrofluid), charging ratio, heat input, and application of magnetic field on the overall thermal performance of the OLPHPs are investigated. Experimental results show that ferrofluid has better heat transport capability relative to SC ferrofluid. Furthermore, application of magnetic field improves the heat transfer performance of OLPHPs charged with both ferrofluids.

Thermal Characters of Mesh Structure in a Flat Heat Pipe

2003 ◽  
Author(s):  
Liang-Han Chien ◽  
Y.-C. Shih
Keyword(s):  
Heat Pipe ◽  
Inclination Angle ◽  
Mesh Size ◽  
Heat Pipes ◽  
Theoretical Models ◽  
Working Fluid ◽  
Internal Space ◽  
Mesh Structure ◽  
Horizontal Orientation ◽  
Plate Type

In this study plate type heat pipes having mesh capillaries were investigated experimentally and theoretically. A test apparatus was designed to test thermal performance of plate type copper-water heat pipe having one or two layers of #50 or #80 mesh capillary structures with 5-to-50 W heat input. The working fluid, water is charged with 25% or 33% volume of the heat pipe internal space. In addition to horizontal orientation, the heat pipes were tested with the evaporator section elevated up to 40 degree inclination angle. Temperature distribution of the heat pipe was measured, and the evaporator, adiabatic and condensation resistances of the heat pipe were calculated separated. The effects of mesh size, charge volume, and inclination angle on each thermal resistance were discussed. In general, the #80 mesh yields lower thermal resistances than the #50 mesh; inclination angle has more significant effect on condenser than evaporator. Theoretical models of evaporation and condensation in flat heat pipes were proposed to interpolate the experimental results. The present evaporation model predicts the experimental data of evaporation resistance between −20% and +30%, and the condensation model predicts most condensation resistance data within ±30%.

Circulation Effectiveness of Working Fluid in Inclined Micro Heat Pipes

2015 ◽  
Vol 789-790 ◽  
pp. 422-425
Author(s):  
Fun Liang Chang ◽  
Yew Mun Hung
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Heat Pipes ◽  
Operating Conditions ◽  
Circulation Rate ◽  
Working Fluid ◽  
High Heat Flux ◽  
Micro Heat Pipe ◽  
Micro Heat Pipes

Micro heat pipe is a two-phase heat transfer device offering effective high heat-flux removal in electronics cooling. Essentially, micro heat pipe relies on the phase change processes, namely evaporation and condensation, and the circulation of working fluid to function as heat transfer equipment. The vast applications of micro heat pipe in portable appliances necessitate its functionality under different orientations with respect to gravity. Therefore, its thermal performance is strongly related to its orientation. By incorporating solid wall conduction, together with the continuity, momentum, and energy equations of the working fluid, a mathematical model is developed to investigate the heat and fluid flow characteristics of inclined micro heat pipes. We investigate both the favorable and adverse effects of gravity on the circulation rate which is intimately related to the thermal performance of micro heat pipes. The effects of gravity, through the angle of inclination, on the circulation strength and heat transport capacity are analysed. This study serves as a useful analytical tool in the micro heat pipe design and performance analysis, associated with different inclinations and operating conditions.

Use of an Inorganic Aqueous Solution to Prevent Non-Condensable Gas Formation in Aluminum Heat Pipes

2013 ◽  
Author(s):  
Michael Stubblebine ◽  
Sean Reilly ◽  
Qi Yao ◽  
Ivan Catton
Keyword(s):  
Heat Transfer ◽  
Aqueous Solution ◽  
Heat Pipe ◽  
Heat Pipes ◽  
Solid Metal ◽  
Aluminum Surface ◽  
Working Fluid ◽  
Water Based ◽  
Inorganic Aqueous Solution ◽  
Over Time

Heat pipes are used in many applications as an effective means for transferring heat from a source to a sink. The basic heat pipe typically consists of a solid metal casing within which a working fluid is sealed inside at a given pressure. The latent heat transfer via the heat pipe’s working fluid allows it to carry a larger amount of heat energy than would normally be possible with an identically dimensioned solid metal rod. Water is often used as a working fluid due to its high heat of vaporization and suitable operating range for electronics cooling. For many applications, especially space, aluminum is desired as a casing material for its high thermal conductivity, low weight, and low cost. However, water is incompatible for use with aluminum heat pipes because it forms a non-condensable gas (NCG), hydrogen, when they contact. In this work, an inorganic aqueous solution (IAS), which has thermophysical properties similar to water, has been used as the working fluid with an aluminum alloy 5052-H2 casing. The prepared thermosiphon underwent long-term lifetime testing and the results indicate no tube failure or significant NCG formation for the duration of the 9 week study. Furthermore, the data indicate that the IAS fluid not only inhibited NCG production but also led to a reduction in heat pipe thermal resistance over time. It is believed that the chemicals in IAS react with the aluminum surface to create a compact oxide layer and electrochemical reaction which prevents hydrogen generation. A secondary, hydrophilic surface coating is also generated by the fluid on top of the first oxide (passivation) layer. This hydrophilic layer is believed to be responsible for the heat transfer enhancement which was observed during testing and the reduction in ΔT (defined as Tevap−Tcond) over time. Aluminum heat pipes used currently in practice utilize ammonia, or other non-water based working fluids, which have inferior latent heats of vaporization compared to water or an aqueous-based fluid such as IAS. The use of aluminum heat pipe casings in combination with a water-based fluid such as IAS has the potential to provide a significant increase in heat transport capability per device unit mass over traditional ammonia charged aluminum heat pipes.

Fundamental Heat Transfer Experiments of Heat Pipes for Turbine Cooling

1998 ◽  
Vol 120 (3) ◽  
pp. 580-587 ◽  
Author(s):  
S. Yamawaki ◽  
T. Yoshida ◽  
M. Taki ◽  
F. Mimura
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Cooling System ◽  
Infrared Image ◽  
Heat Pipes ◽  
Performance Criteria ◽  
Working Fluid ◽  
Steel Shell ◽  
Turbine Cooling ◽  
Start Up

Fundamental heat transfer experiments were carried out for three kinds of heat pipes that may be applied to turbine cooling in future aero-engines. In the turbine cooling system with a heat pipe, heat transfer rate and start-up time of the heat pipe are the most important performance criteria to evaluate and compare with conventional cooling methods. Three heat pipes are considered, called heat pipe A, B, and C, respectively. All heat pipes have a stainless steel shell and nickel sintered powder metal wick. Sodium (Na) was the working fluid for heat pipes A and B; heat pipe C used eutectic sodium-potassium (NaK). Heat pipes B and C included noncondensible gas for rapid start-up. There were fins on the cooling section of heat pipes. In the experiments, and infrared image furnace supplied heat to the heat pipe simulating turbine blade surface conditions. In the results, heat pipe B demonstrated the highest heat flux of 17 to 20 W/cm2. The start-up time was about 6 minutes for heat pipe B and about 16 minutes for heat pipe A. Thus, adding noncondensible gas effectively reduced start-up time. Although NaK is a liquid phase at room temperature, the startup time of heat pipe C (about 7 to 8 minutes) was not shorter than the heat pipe B. The effect of a gravitational force on heat pipe performance was also estimated by inclining the heat pipe at an angle of 90 deg. There was no significant gravitational dependence on heat transport for heat pipes including noncondensible gas.

Experimental Investigation on Nanofluids Effectiveness on Heat Transfer in Oscillating Heat Pipe

2013 ◽  
Vol 856 ◽  
pp. 98-102 ◽  
Author(s):  
Hamid R. Goshayeshi ◽  
Ali Khosravi ◽  
Mehdi Abedpour Karizaki
Keyword(s):  
Heat Transfer ◽  
Experimental Investigation ◽  
Heat Pipe ◽  
High Speed ◽  
Oscillatory Flow ◽  
Glass Tube ◽  
Heat Pipes ◽  
Oscillating Heat Pipe ◽  
Flow And Heat Transfer ◽  
Heat Loads

An experimental investigation of the oscillatory flow and heat transfer in a vertical oscillating heat pipe (OHP) was conducted. The oscillating heat pipe was made of a copper-glass tube. Flow inside the oscillating heat pipe at different heat loads was recorded by a high speed camera. Through this research, the authors investigated the effect of utilizing nanofluids on heat transfer amount in heat pipes. The employed nanofluids in this study were water-Fe2O3, water-SiO2and water-TiO2with various volumetric concentrations. The results show that after adding nanoparticles in the base fluid (here water) heat transfer rate increases significantly. It's also noteworthy, of the all applied nanofluids, water-TiO2mixture presents the best enhancement in heat transfer amount.

scholarly journals Analysis on heat transfer and start-up performance of mercury heat pipe

2021 ◽  
Vol 245 ◽  
pp. 03012
Author(s):  
Xiuxiang Zhang ◽  
Kang He ◽  
Quan Yang ◽  
Chengcai Xi
Keyword(s):  
Heat Transfer ◽  
Thermal Resistance ◽  
Heat Pipe ◽  
Saturated Vapor ◽  
Heating Power ◽  
Good Thermal Stability ◽  
Start Up ◽  
Steady State Heat ◽  
Steady State Heat Transfer ◽  
Transient Thermal

Mercury heat pipe has the advantages of good thermal stability and low saturated vapor pressure, which is the best choice for the transition from water heat pipe to liquid metal heat pipe. The effects of heating power and heat pipe structure on start-up time and steady-state heat transfer performance of mercury heat pipe were studied by using transient thermal network model. The results showed that: 1) Increasing the length of condenser is beneficial to reducing the start-up time and thermal resistance; 2) Increasing the heating power or wall thickness will reduce the thermal resistance, but increase the start-up time, and increasing the porosity of wick is just the opposite; 3) Increasing the thickness of wick can increase both the start-up time and the thermal resistance.

scholarly journals Fundamental Heat Transfer Experiments of Heat Pipes for Turbine Cooling

1997 ◽  
Author(s):  
Shigemichi Yamawaki ◽  
Toyoaki Yoshida ◽  
Masanobu Taki ◽  
Fujio Mimura
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Cooling System ◽  
Infrared Image ◽  
Heat Pipes ◽  
Performance Criteria ◽  
Working Fluid ◽  
Steel Shell ◽  
Turbine Cooling ◽  
Start Up

Fundamental heat transfer experiments were carried out for three kinds of heat pipes which may be applied to turbine cooling in future aero-engines. In the turbine cooling system with a heat pipe, heat transfer rate and start-up time of the heat pipe are the most important performance criteria to evaluate and compare with conventional cooling methods. Three heat pipes are considered, called heat pipe A, B and C, respectively. All heat pipes have a stainless steel shell and nickel sintered powder metal wick. Sodium(Na) was the working fluid for heat pipes A and B; heat pipe C used eutectic sodium-potassium(NaK). Heat pipes B and C included non-condensible gas for rapid start-up. There were fins on the cooling section of heat pipes. In the experiments, an infrared image furnace supplied heat to the heat pipe simulating turbine blade surface conditions. In the results, heat pipe B demonstrated the highest heat flux of 17 to 20 W/cm2. The start-up time was about 6 minutes for heat pipe B and about 16 minutes for heat pipe A. Thus adding non-condensible gas effectively reduced start-up time. Although NaK is a liquid phase at room temperature, the start-up time of heat pipe C (about 7 to 8 minutes) was not shorter than the heat pipe B. The effect of a gravitational force on heat pipe performance was also estimated by inclining the heat pipe at an angle of 90 degrees. There was no significant gravitational dependence on heat transport for heat pipes including non-condensible gas.

Sign in / Sign up

Export Citation Format

Share Document