Cooling of a Finned Cylinder by a Jet Flow of Air

2002 ◽  
Author(s):  
F. Gori ◽  
F. De Nigris ◽  
E. Pippione ◽  
G. Scavarda
Keyword(s):  
Heat Transfer ◽  
Cooling System ◽  
Jet Flow ◽  
Impinging Jets ◽  
Transfer Coefficients ◽  
Electric System ◽  
Heavy Trucks ◽  
Turbo Compressor ◽  
University Of Rome ◽  
The University

The paper describes a patented proposal to use jets of air in the cooling system of heavy trucks. Preliminary tests have been carried out, in the Heat Transfer Laboratory of the University of Rome “Tor Vergata”, to evaluate the heat transfer characteristics of a jet flow of air, impinging onto an externally finned cylinder. The cylinder is internally heated with an electric system. Thermocouples, located inside the cylinder, allow to measure the wall temperatures, in order to calculate the local and average convective heat transfer coefficients. A preliminary design of the practical apparatus, applied to heavy trucks, has been done in cooperation with Iveco. Nozzles are designed to be put after the fan of heavy trucks to converge air, in the form of jets, onto the tube where the charged air is flowing from the outlet of the turbo-compressor. The efficiency of the jet flow increases the cooling performances but, due to the high temperature at the outlet of the turbo-compressor, it may not be enough. The heat transfer cooling performances are enhanced if the tube to be cooled is externally finned. Some preliminary experiments have been carried out in a real scale bank test of an heavy truck engine at the Engineering Testing Laboratories Department of Iveco. Comparisons are done between the experiments and a simple theoretical model. Some conclusions are drawn about the cooling at different fluid dynamics conditions of the impinging jets.

Cooling of a Finned Cylinder by a Jet Flow of Air

2003 ◽  
Author(s):  
F. Gori ◽  
M. Borgia ◽  
A. Doro Altan
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Wall Temperature ◽  
Experimental Tests ◽  
Jet Flow ◽  
Heat Transfer Characteristics ◽  
Transfer Coefficients ◽  
Electric System ◽  
Heat Transfer Coefficients ◽  
Convective Heat Transfer Coefficients

Experimental tests have been carried out to evaluate the heat transfer characteristics on an externally finned cylinder impinged by a jet flow of air. The cylinder is internally heated with an electric system. Thermocouples located inside the cylinder allow to evaluate the wall temperature distribution, in order to calculate the local and average convective heat transfer coefficients.

Heat Transfer Characteristics of an Angled Array Impinging Jet on a Concave Duct

2012 ◽  
Author(s):  
Eui Yeop Jung ◽  
Chan Ung Park ◽  
Dong Hyun Lee ◽  
Kyung Min Kim ◽  
Ta-kwan Woo ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Cooling System ◽  
Jet Impingement ◽  
Impinging Jet ◽  
Impinging Jets ◽  
Heat Transfer Characteristics ◽  
Transfer Coefficients ◽  
Stagnation Points ◽  
Transfer Characteristics ◽  
Jet Cooling

This study investigated the heat transfer characteristics of an array jet cooling system on a concave surface. Two types of injection holes were used: one for impinging jets normal to the impingement surface, and the other for angled impinging jets. For the normal jets, the jet Reynolds number (Re) based on the hole diameter varied from 3,000 to 10,000, and the height-to-diameter ratio (H/d) was fixed at 1.0. There were 15 injection holes positioned in a staggered 3×5 array. For the angled jets, Re was set to 5,000 and H/d was also fixed at 1.0. Naphthalene sublimation method was used to determine the heat transfer coefficients on the targeted plates. For normal impinging jet cooling, separate peaks were observed at the stagnation regions due to the curvature effect. Since a crossflow was generated by air spent from the jet arrays, the crossflow effect increased as it moved downstream. Due to the interaction between the crossflow and impinging jets, the peak values at the stagnation points increased downstream. The heat transfer coefficient on the targeted plate increased with Re. The average Sh of the angled jets was higher than that of the normal jets, as the obliquely impinging jet increased the mass flow rate and mass interaction between the jet impingement points.

scholarly journals Numerical Evaluation of a HVAC System Based on a High-Performance Heat Transfer Fluid

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3298
Author(s):  
Gianpiero Colangelo ◽  
Brenda Raho ◽  
Marco Milanese ◽  
Arturo de Risi
Keyword(s):  
Heat Transfer ◽  
High Performance ◽  
Cooling System ◽  
Electrical Energy ◽  
Simulation Software ◽  
Heat Transfer Fluid ◽  
Hvac System ◽  
Dynamic Simulations ◽  
Heating And Cooling ◽  
The University

Nanofluids have great potential to improve the heat transfer properties of liquids, as demonstrated by recent studies. This paper presents a novel idea of utilizing nanofluid. It analyzes the performance of a HVAC (Heating Ventilation Air Conditioning) system using a high-performance heat transfer fluid (water-glycol nanofluid with nanoparticles of Al2O3), in the university campus of Lecce, Italy. The work describes the dynamic model of the building and its heating and cooling system, realized through the simulation software TRNSYS 17. The use of heat transfer fluid inseminated by nanoparticles in a real HVAC system is an innovative application that is difficult to find in the scientific literature so far. This work focuses on comparing the efficiency of the system working with a traditional water-glycol mixture with the same system that uses Al2O3-nanofluid. The results obtained by means of the dynamic simulations have confirmed what theoretically assumed, indicating the working conditions of the HVAC system that lead to lower operating costs and higher COP and EER, guaranteeing the optimal conditions of thermo-hygrometric comfort inside the building. Finally, the results showed that the use of a nanofluid based on water-glycol mixture and alumina increases the efficiency about 10% and at the same time reduces the electrical energy consumption of the HVAC system.

Thermal Analysis of Cooling System in a Gas Turbine Transition Piece

2011 ◽  
Author(s):  
Jun Su Park ◽  
Namgeon Yun ◽  
Hokyu Moon ◽  
Kyung Min Kim ◽  
Sin-Ho Kang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Thermal Stresses ◽  
Cooling System ◽  
Structural Information ◽  
Thermal Analyses ◽  
Thermal Design ◽  
Transfer Coefficients ◽  
Transition Piece ◽  
Inlet Conditions

This paper presents thermal analyses of the cooling system of a transition piece, which is one of the primary hot components in a gas turbine engine. The thermal analyses include heat transfer distributions induced by heat and fluid flow, temperature, and thermal stresses. The purpose of this study is to provide basic thermal and structural information on transition piece, to facilitate their maintenance and repair. The study is carried out primarily by numerical methods, using the commercial software, Fluent and ANSYS. First, the combustion field in a combustion liner with nine fuel nozzles is analyzed to determine the inlet conditions of a transition piece. Using the results of this analysis, pressure distributions inside a transition piece are calculated. The outside of the transition piece in a dump diffuser system is also analyzed. Information on the pressure differences is then used to obtain data on cooling channel flow (one of the methods for cooling a transition piece). The cooling channels have exit holes that function as film-cooling holes. Thermal and flow analyses are carried out on the inside of a film-cooled transition piece. The results are used to investigate the adjacent temperatures and wall heat transfer coefficients inside the transition piece. Overall temperature and thermal stress distributions of the transition piece are obtained. These results will provide a direction to improve thermal design of transition piece.

Experimental Investigation of Local Heat Transfer Distribution on Smooth and Roughened Surfaces Under an Array of Angled Impinging Jets

2001 ◽  
Author(s):  
Lamyaa A. El-Gabry ◽  
Deborah A. Kaminski
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Cross Flow ◽  
Local Heat Transfer ◽  
Reynolds Numbers ◽  
Local Heat ◽  
Impinging Jets ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Roughened Surface

Abstract Measurements of the local heat transfer distribution on smooth and roughened surfaces under an array of angled impinging jets are presented. The test rig is designed to simulate impingement with cross-flow in one direction which is a common method for cooling gas turbine components such as the combustion liner. Jet angle is varied between 30, 60, and 90 degrees as measured from the impingement surface, which is either smooth or randomly roughened. Liquid crystal video thermography is used to capture surface temperature data at five different jet Reynolds numbers ranging between 15,000 and 35,000. The effect of jet angle, Reynolds number, gap, and surface roughness on heat transfer efficiency and pressure loss is determined along with the various interactions among these parameters. Peak heat transfer coefficients for the range of Reynolds number from 15,000 to 35,000 are highest for orthogonal jets impinging on roughened surface; peak Nu values for this configuration ranged from 88 to 165 depending on Reynolds number. The ratio of peak to average Nu is lowest for 30-degree jets impinging on roughened surfaces. It is often desirable to minimize this ratio in order to decrease thermal gradients, which could lead to thermal fatigue. High thermal stress can significantly reduce the useful life of engineering components and machinery. Peak heat transfer coefficients decay in the cross-flow direction by close to 24% over a dimensionless length of 20. The decrease of spanwise average Nu in the crossflow direction is lowest for the case of 30-degree jets impinging on a roughened surface where the decrease was less than 3%. The decrease is greatest for 30-degree jet impingement on a smooth surface where the stagnation point Nu decreased by more than 23% for some Reynolds numbers.

Heat Transfer Measurements in an Internal Cooling System Using a Transient Technique With Infrared Thermography

2012 ◽  
Author(s):  
Christian Egger ◽  
Jens von Wolfersdorf ◽  
Martin Schnieder
Keyword(s):  
Heat Transfer ◽  
Data Analysis ◽  
Infrared Thermography ◽  
Outer Surface ◽  
Cooling System ◽  
Internal Cooling ◽  
Test Model ◽  
Cooling Channel ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

In this paper a transient method for measuring heat transfer coefficients in internal cooling systems using infrared thermography is applied. The experiments are performed with a two-pass internal cooling channel connected by a 180° bend. The leading edge and the trailing edge consist of trapezoidal and nearly rectangular cross sections, respectively, to achieve an engine-similar configuration. Within the channels rib arrangements are considered for heat transfer enhancement. The test model is made of metallic material. During the experiment the cooling channels are heated by the internal flow. The surface temperature response of the cooling channel walls is measured on the outer surface by infrared thermography. Additionally, fluid temperatures as well as fluid and solid properties are determined for the data analysis. The method for determining the distribution of internal heat transfer coefficients is based on a lumped capacitance approach which considers lateral conduction in the cooling system walls as well as natural convection and radiation heat transfer on the outer surface. Because of time-dependent effects a sensitivity analysis is performed to identify optimal time periods for data analysis. Results are compared with available literature data.

Evaluation of Numerical Methods to Predict Temperature Distributions of an Experimentally Investigated Convection-Cooled Gas-Turbine Blade

2017 ◽  
Author(s):  
E. Findeisen ◽  
B. Woerz ◽  
M. Wieler ◽  
P. Jeschke ◽  
M. Rabs
Keyword(s):  
Heat Transfer ◽  
Numerical Methods ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Gas Turbines ◽  
Cooling System ◽  
Fe Model ◽  
Gas Turbine Blade ◽  
Transfer Coefficients ◽  
Temperature Distributions

This paper presents two different numerical methods to predict the thermal load of a convection-cooled gas-turbine blade under realistic operating temperature conditions. The subject of the investigation is a gas-turbine rotor blade equipped with an academic convection-cooling system and investigated at a cascade test-rig. It consists of three cooling channels, which are connected outside the blade, so allowing cooling air temperature measurements. Both methods use FE models to obtain the temperature distribution of the solid blade. The difference between these methods lies in the generation of the heat transfer coefficients along the cooling channel walls which serve as a boundary condition for the FE model. One method, referred to as the FEM1D method, uses empirical one-dimensional correlations known from the available literature. The other method, the FEM2D method, uses three-dimensional CFD simulations to obtain two-dimensional heat transfer coefficient distributions. The numerical results are compared to each other as well as to experimental data, so that the benefits and limitations of each method can be shown and validated. Overall, this paper provides an evaluation of the different methods which are used to predict temperature distributions in convection-cooled gas-turbines with regard to accuracy, numerical cost and the limitations of each method. The temperature profiles obtained in all methods generally show good agreement with the experiments. However, the more detailed methods produce more accurate results by causing higher numerical costs.

MEMS Impinging-Jet Cooling

2000 ◽  
Author(s):  
Qiao Lin ◽  
Shuyun Wu ◽  
Yin Yuen ◽  
Yu-Chong Tai ◽  
Chin-Ming Ho
Keyword(s):  
Heat Transfer ◽  
Heat Exchangers ◽  
Jet Impingement ◽  
Impinging Jet ◽  
Impinging Jets ◽  
Measured Temperature ◽  
Transfer Coefficients ◽  
Element Analysis ◽  
Heat Transfer Coefficients ◽  
Jet Cooling

Abstract This paper presents an experimental investigation on MEMS impinging jets as applied to micro heat exchangers. We have fabricated MEMS single and array jet nozzles using DRIE technology, as well as a MEMS quartz chip providing a simulated hot surface for jet impingement. The quartz chip, with an integrated polysilicon thin-film heater and distributed temperature sensors, offers high spatial resolution in temperature measurement due to the low thermal conductivity of quartz. From measured temperature distributions, heat transfer coefficients are computed for single and array micro impinging jets using finite element analysis. The results from this study for the first time provide extensive data on spatial distributions of micro impinging-jet heat transfer coefficients, and demonstrate the viability of MEMS heat exchangers that use micro impinging jets.

Heat Transfer Enhancement by Turbulent Impinging Jets

2000 ◽  
Author(s):  
M. Kumagai ◽  
R. S. Amano ◽  
M. K. Jensen
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Stokes Equations ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Impinging Jets ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

Abstract A numerical and experimental investigation on cooling of a solid surface was performed by studying the behavior of an impinging jet onto a fixed flat target. The local heat transfer coefficient distributions on a plate with a constant heat flux were computationally investigated with a normally impinging axisymmetric jet for nozzle diameter of 4.6mm at H/d = 4 and 10, with the Reynolds numbers of 10,000 and 40,000. The two-dimensional cylindrical Navier-Stokes equations were solved using a two-equation k-ε turbulence model. The finite-volume differencing scheme was used to solve the thermal and flow fields. The predicted heat transfer coefficients were compared with experimental measurements. A universal function based on the wave equation was developed and applied to the heat transfer model to improve calculated local heat transfer coefficients for short nozzle-to-plate distance (H/d = 4). The differences between H/d = 4 and 10 due to the correlation among heat transfer coefficient, kinetic energy and pressure were investigated for the impingement region. Predictions by the present model show good agreement with the experimental data.

Recent Trends of Impingement Cooling System Enhancement for Gas Turbine

2013 ◽  
Vol 465-466 ◽  
pp. 496-499
Author(s):  
Mohd Firdaus Bin Abas ◽  
Abdullah Aslam ◽  
Hamidon bin Salleh ◽  
Nor Adrian Bin Nor Salim
Keyword(s):  
Heat Transfer ◽  
Cooling System ◽  
Turbine Blades ◽  
Impinging Jets ◽  
Target Plate ◽  
Impingement Cooling ◽  
Impingement Jet ◽  
Rib Turbulators ◽  
Recent Trends ◽  
Plate Distance

Efforts have been given to improve the turbine blades ability to withstand high temperature for a long period of time by implementing effective cooling system. There are many aspects that should be considered when implementing impingement cooling. This paper will only cover two trending aspects in impingement cooling implementation; the jet-to-target plate distance and the application of ribs in promoting better impingement cooling performance. For target plate distance to impingement jet diameter value, H/d > 1, the area-averaged Nusselt number also decreases as the H/d value increases. This may have been due to a reduction of the amount of momentum exerted by the impinging jets onto the target plate. For H/d < 1, the results have been proven otherwise. Heat transfer in impingement/effusion cooling system in crossflow with rib turbulators showed higher heat transfer rate than that of a surface without ribs because the ribs prevent the wall jets from being swept away by the crossflow and increase local turbulence of the flow near the surface. It could be concluded that both H/d ratio and ribs installation play an important role in enhancing impingement cooling systems heat transfer effectiveness.

Sign in / Sign up

Export Citation Format

Share Document