FEM/BEM Simulation of Vibroacoustics of a Fluid-Loaded, Stiffened Plate Under Combined Force-Moment Excitation

2000 ◽  
Author(s):  
H. Zheng ◽  
C. Cai ◽  
G. R. Liu ◽  
K. Y. Lam
Keyword(s):  
Numerical Simulation ◽  
Acoustic Radiation ◽  
Normal Modes ◽  
Vibration Response ◽  
Structural Vibration ◽  
Stiffened Plate ◽  
Coupled Modes ◽  
Force Moment ◽  
Surrounding Fluid ◽  
Element Method

Abstract A numerical simulation of structural vibration and acoustic radiation is presented for a finite, fluid-loaded plate reinforced with two sets of orthotropic stiffeners. The attempt is to achieve a physical understanding of the dynamic behaviour and especially the acoustic radiation of the stiffened plate under combined force and moment excitations. Finite element method (FEM) is employed for calculation of the in-vacuo normal modes of the stiffened plate. The coupled modes with a heavy fluid (water), vibration response and acoustic radiation of the plate under given force and/or moment excitation are calculated using boundary element method (BEM). Numerical simulation results are detailed to address the significance of moment in combined force-moment excitations and, more importantly, the cancelling of the combined excitation in both structural vibration response and the associated acoustic radiation into the surrounding fluid.

scholarly journals Infinite Elements and Their Influence on Normal and Radiation Modes in Exterior Acoustics

2017 ◽  
Vol 25 (04) ◽  
pp. 1650020 ◽  
Author(s):  
Lennart Moheit ◽  
Steffen Marburg
Keyword(s):  
Degrees Of Freedom ◽  
Acoustic Radiation ◽  
Computational Cost ◽  
Normal Modes ◽  
Higher Order ◽  
Infinite Elements ◽  
Odd Order ◽  
Infinite Element Method ◽  
Interpolation Polynomials ◽  
Element Method

Acoustic radiation modes (ARMs) and normal modes (NMs) are calculated at the surface of a fluid-filled domain around a solid structure and inside the domain, respectively. In order to compute the exterior acoustic problem and modes, both the finite element method (FEM) and the infinite element method (IFEM) are applied. More accurate results can be obtained by using finer meshes in the FEM or higher-order radial interpolation polynomials in the IFEM, which causes additional degrees of freedom (DOF). As such, more computational cost is required. For this reason, knowledge about convergence behavior of the modes for different mesh cases is desirable, and is the aim of this paper. It is shown that the acoustic impedance matrix for the calculation of the radiation modes can be also constructed from the system matrices of finite and infinite elements instead of boundary element matrices, as is usually done. Grouping behavior of the eigenvalues of the radiation modes can be observed. Finally, both kinds of modes in exterior acoustics are compared in the example of the cross-section of a recorder in air. When the number of DOF is increased by using higher-order radial interpolation polynomials, different eigenvalue convergences can be observed for interpolation polynomials of even and odd order.

Application of the Boundary Element Method and Modal Analysis to Tire Acoustics Problems

1993 ◽  
Vol 21 (2) ◽  
pp. 66-90 ◽  
Author(s):  
Y. Nakajima ◽  
Y. Inoue ◽  
H. Ogawa
Keyword(s):  
Finite Element ◽  
Boundary Element Method ◽  
Boundary Element ◽  
Acoustic Radiation ◽  
Traffic Noise ◽  
Noise Prediction ◽  
Prediction System ◽  
Tire Noise ◽  
Acoustic Contribution ◽  
Element Method

Abstract Road traffic noise needs to be reduced, because traffic volume is increasing every year. The noise generated from a tire is becoming one of the dominant sources in the total traffic noise because the engine noise is constantly being reduced by the vehicle manufacturers. Although the acoustic intensity measurement technology has been enhanced by the recent developments in digital measurement techniques, repetitive measurements are necessary to find effective ways for noise control. Hence, a simulation method to predict generated noise is required to replace the time-consuming experiments. The boundary element method (BEM) is applied to predict the acoustic radiation caused by the vibration of a tire sidewall and a tire noise prediction system is developed. The BEM requires the geometry and the modal characteristics of a tire which are provided by an experiment or the finite element method (FEM). Since the finite element procedure is applied to the prediction of modal characteristics in a tire noise prediction system, the acoustic pressure can be predicted without any measurements. Furthermore, the acoustic contribution analysis obtained from the post-processing of the predicted results is very helpful to know where and how the design change affects the acoustic radiation. The predictability of this system is verified by measurements and the acoustic contribution analysis is applied to tire noise control.

scholarly journals Numerical simulation on coal loading process of shearer drum based on discrete element method

2021 ◽  
pp. 014459872110135
Author(s):  
Zhen Tian ◽  
Shuangxi Jing ◽  
Lijuan Zhao ◽  
Wei Liu ◽  
Shan Gao
Keyword(s):  
Numerical Simulation ◽  
Discrete Element Method ◽  
Loading Rate ◽  
Low Cost ◽  
Element Model ◽  
Discrete Element ◽  
Helix Angle ◽  
Loading Process ◽  
Coal Particles ◽  
Element Method

The drum is the working mechanism of the coal shearer, and the coal loading performance of the drum is very important for the efficient and safe production of coal mine. In order to study the coal loading performance of the shearer drum, a discrete element model of coupling the drum and coal wall was established by combining the results of the coal property determination and the discrete element method. The movement of coal particles and the mass distribution in different areas were obtained, and the coal particle velocity and coal loading rate were analyzed under the conditions of different helix angles, rotation speeds, traction speeds and cutting depths. The results show that with the increase of helix angle, the coal loading first increases and then decreases; with the increase of cutting depth and traction speed, the coal loading rate decreases; the increase of rotation speed can improve the coal loading performance of drum to a certain extent. The research results show that the discrete element numerical simulation can accurately reflect the coal loading process of the shearer drum, which provides a more convenient, fast and low-cost method for the structural design of shearer drum and the improvement of coal loading performance.

Sign in / Sign up

Export Citation Format

Share Document