Strain Rate Effect on Dynamic Compressive Failures in Off-Axis Glass-Epoxy Composites

2000 ◽  
Author(s):  
Jialin Tsai ◽  
C. T. Sun
Keyword(s):  
Shear Modulus ◽  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
Strain Rates ◽  
Compression Tests ◽  
Hopkinson Pressure Bar ◽  
Rate Dependent ◽  
Bifurcation Buckling ◽  
Split Hopkinson ◽  
Pressure Bar

Abstract Dynamic compressive strength of off-axis S2/8552 glass-epoxy composite in the form of fiber microbuckling was studied. Based on the bifurcation buckling analysis, the microbuckling stress is approximately equal to the composite tangent shear modulus. Using a viscoplastic constitutive model to describe the composite tangent shear modulus, microbuckling stresses at various strain rates were predicted. Small angle off-axis composite specimens were tested to failure at various strain rates. For strain rates below 1/sec, the compression tests were conducted on an MTS machine, while higher strain rate tests were carried out using a Split Hopkinson Pressure Bar (SHPB). Fiber microbuckling was found to be the dominant failure mode for 5°, 10° and 15° specimens within the range of tested strain rates. Comparison of model prediction with experimental data shows that the rate-dependent microbuckling model can be used for predicting compressive strengths at strain rates up to 1100/s.

scholarly journals Study on the dynamic properties of AM-SLM AlSi10Mg alloy using the Split Hopkinson Pressure Bar (SHPB) technique

2018 ◽  
Vol 183 ◽  
pp. 04005 ◽  
Author(s):  
Bar Nurel ◽  
Moshe Nahmany ◽  
Adin Stern ◽  
Nahum Frage ◽  
Oren Sadot
Keyword(s):  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Properties ◽  
Rate Sensitivity ◽  
Strain Rate Range ◽  
Strain Rates ◽  
Hopkinson Pressure Bar ◽  
Static Mechanical ◽  
Split Hopkinson ◽  
Pressure Bar

Additive manufacturing by Selective Laser Melting of metals is attracting substantial attention, due to its advantages, such as short-time production of customized structures. This technique is useful for building complex components using a metallic pre-alloyed powder. One of the most used materials in AMSLM is AlSi10Mg powder. Additively manufactured AlSi10Mg may be used as a structural material and it static mechanical properties were widely investigated. Properties in the strain rates of 5×102–1.6×103 s-1 and at higher strain rates of 5×103 –105 s-1 have been also reported. The aim of this study is investigation of dynamic properties in the 7×102–8×103 s-1 strain rate range, using the split Hopkinson pressure bar technique. It was found that the dynamic properties at strain-rates of 1×103–3×103 s-1 depend on a build direction and affected by heat treatment. At higher and lower strain-rates the effect of build direction is limited. The anisotropic nature of the material was determined by the ellipticity of samples after the SHPB test. No strain rate sensitivity was observed.

Using Split Hopkinson Pressure Bars to Perform Large Strain Compression Tests on Neoprene at Intermediate and High Strain Rates

2013 ◽  
Vol 631-632 ◽  
pp. 458-462 ◽  
Author(s):  
Peng Duo Zhao ◽  
Yu Wang ◽  
Jian Ye Du ◽  
Lei Zhang ◽  
Zhi Peng Du ◽  
...  
Keyword(s):  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Large Strain ◽  
Rate Sensitivity ◽  
Strain Rates ◽  
Compression Tests ◽  
Hopkinson Pressure Bar ◽  
High Strain Rates ◽  
Split Hopkinson ◽  
Pressure Bar

The strain rate sensitivity of neoprene is characterized using a modified split Hopkinson pressure bar (SHPB) system at intermediate (50 s-1, 100 s-1) and high (500 s-1, 1000 s-1) strain rates. We used two quartz piezoelectric force transducers that were sandwiched between the specimen and experimental bars respectively to directly measure the weak wave signals. A laser gap gage was employed to monitor the deformation of the sample directly. Three kinds of neoprene rubbers (Shore hardness: SHA60, SHA65, and SHA70) were tested using the modified split Hopkinson pressure bar. Experimental results show that the modified apparatus is effective and reliable for determining the compressive stress-strain responses of neoprene at intermediate and high strain rates.

Studies on the Dynamic Compressive Properties of Open-Celled Aluminum Alloy Foams

2006 ◽  
Vol 306-308 ◽  
pp. 905-910 ◽  
Author(s):  
Zhi Hua Wang ◽  
Hong Wei Ma ◽  
Long Mao Zhao ◽  
Gui Tong Yang
Keyword(s):  
Yield Strength ◽  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
Strain Rates ◽  
Hopkinson Pressure Bar ◽  
Aluminum Foams ◽  
Wide Range ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
Dynamic Loading Conditions

The compressive deformation behavior of open-cell aluminum foams with different densities and morphologies was assessed under quasi-static and dynamic loading conditions. High strain rate experiments were conducted using a split Hopkinson pressure bar technique at strain rates ranging from 500 to 1 2000 − s . The experimental results shown that the compressive stress-strain curves of aluminum foams also have the “ three regions” character appeared in general foam materials, namely elastic region, collapse region and densification regions. It is found that density is the primary variable characterizing the modulus and yield strength of foams and the cell appears to have a negligible effect on the strength of foams. It also is found that yield strength and energy absorption is almost insensitive to strain rate and deformation is spatially uniform for the open-celled aluminum foams, over a wide range of strain rates.

High Strain-Rate Compressive Characteristics of Carbon/Epoxy Laminated Composites in Through-Thickness Direction

2004 ◽  
Vol 1-2 ◽  
pp. 11-16 ◽  
Author(s):  
Takashi Yokoyama
Keyword(s):  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
Laminated Composites ◽  
Fiber Direction ◽  
Strain Rates ◽  
Thickness Direction ◽  
Hopkinson Pressure Bar ◽  
Total Strain Energy ◽  
Split Hopkinson ◽  
Pressure Bar

Compressive stress-strain characteristics of carbon/epoxy laminated composites in the through-thickness direction at strain rates of over 1000/s were evaluated using the standard split Hopkinson pressure bar. Three carbon/epoxy laminated composites (i.e., unidirectional, cross-ply and woven) with almost the same thickness were tested at room temperature. Small solid cylindrical specimens were machined such that the direction of the compression loading was perpendicular to the fiber direction of the laminates. The effects of strain rate and reinforcement geometry on the secant modulus at 1% strain, ultimate compressive strength and strain, and total strain energy to failure were examined in detail.

Measurement of Mechanical Properties of St 37 Material at High Strain Rates Using a Split Hopkinson Pressure Bar

2014 ◽  
Vol 660 ◽  
pp. 562-566 ◽  
Author(s):  
Akbar Afdhal ◽  
Leonardo Gunawan ◽  
Sigit P. Santosa ◽  
Ichsan Setya Putra ◽  
Hoon Huh
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Test Specimen ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Strain Rates ◽  
Hopkinson Pressure Bar ◽  
Stress Strain ◽  
Split Hopkinson ◽  
Pressure Bar

The dynamic mechanical properties of a material are important keys to investigate the impact characteristic of a structure such as a crash box. For some materials, the stress-strain relationships at high strain rate loadings are different than that at the static condition. These mechanical properties depend on the strain rate of the loadings, and hence an appropriate testing technique is required to measure them. To measure the mechanical properties of a material at high strain rates, ranging from 500 s-1 to 10000 s-1, a Split Hopkinson Pressure Bar is commonly used. In the measurements, strain pulses are generated in the bars system, and pulses being reflected and transmitted by a test specimen in the bar system are measured. The stress-strain curves as the material properties of the test specimen are obtained by processing the measured reflected and transmitted pulses. This paper presents the measurements of the mechanical properties of St 37 mild steel at several strain rates using a Split Hopkinson Pressure Bar. The stress-strain curves obtained in the measurement were curve fitted using the Power Law. The results show that the strength of St 37 material increases as the strain rate increases.

scholarly journals Dynamic Behavior of Aluminum Alloy Aw 5005 Undergoing Interfacial Friction and Specimen Configuration in Split Hopkinson Pressure Bar System at High Strain Rates and Temperatures

Materials ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 4614 ◽  
Author(s):  
Amine Bendarma ◽  
Tomasz Jankowiak ◽  
Alexis Rusinek ◽  
Tomasz Lodygowski ◽  
Bin Jia ◽  
...  
Keyword(s):  
Dynamic Response ◽  
Split Hopkinson Pressure Bar ◽  
Strain Rates ◽  
Compression Tests ◽  
Hopkinson Pressure Bar ◽  
Element Analysis ◽  
Wide Range ◽  
Temperature Experiment ◽  
Split Hopkinson ◽  
Pressure Bar

In this paper, experimental and numerical results of an aluminum alloy’s mechanical behavior are discussed. Over a wide range of strain rates (10−4 s−1 ≤ έ ≤ 103 s−1) the influence of the loading impact, velocity and temperature on the dynamic response of the material was analyzed. The interface friction effect on the material’s dynamic response is examined using a split Hopkinson pressure bar (SHPB) in a high temperature experiment using finite element analysis (FEA). The effect of different friction conditions between the specimen and the transmitted/incident bars in the SHPB system was examined using cylinder bulk specimens and cylinder plates defined with four-layer configurations. The results of these tests alongside the presented numerical simulations allow a better understanding of the phenomenon and reduces (minimizes) errors during compression tests at high and low strain rates with temperatures ranging from 21 to 300 °C.

Experiment on Mechanical Behavior of Reinforced Concrete Subjected to Impact Loading

2012 ◽  
Vol 450-451 ◽  
pp. 523-526 ◽  
Author(s):  
Hai Feng Liu ◽  
Wei Wu Yang ◽  
Jian Guo Ning
Keyword(s):  
Reinforced Concrete ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
Peak Stress ◽  
Compression Tests ◽  
Hopkinson Pressure Bar ◽  
Rate Dependent ◽  
Split Hopkinson ◽  
Reinforced Steel ◽  
Pressure Bar

The dynamic compression tests of reinforced concrete with different reinforcement ratios are carried out by split Hopkinson pressure bar (SHPB). Reinforced steel bar is placed along longitudinal and transverse direction. Experimental results show that reinforced concrete is non-linear and rate-dependent. With the enhancement of strain rate, the peak stress of reinforced concrete increases correspondingly

scholarly journals Determination of the high-strain rate elastic modulus of printing resins using two different split Hopkinson pressure bars

2021 ◽  
Author(s):  
S. Aghayan ◽  
S. Bieler ◽  
K. Weinberg
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Properties ◽  
Compression Tests ◽  
Hopkinson Pressure Bar ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
Strain Rate Loading

AbstractThe usage of resin-based materials for 3D printing applications has been growing over the past decades. In this study, two types of resins, namely a MMA-based resin and an ABS-based tough resin, are subjected to compression tests on a split Hopkinson pressure bar to deduce their dynamic properties under high strain rate loading.Two Hopkinson bar setups are used, the first one is equipped with aluminum bars and the second one with PMMA bars. From the measured strain waves, elastic moduli at high strain rates are derived. Both setups lead to values of $E=3.4$ E = 3.4 –3.8 GPa at a strain rate of about 250 s−1. Numerical simulations support the experiments. Moreover, considering the waves gained from the two different bar setups, PMMA bars appear to be well-suited for testing resin samples and are therefore recommended for such applications.

Experimental Research on Dynamic Mechanical Properties of 5083 Aluminum Alloy

2013 ◽  
Vol 535-536 ◽  
pp. 497-500 ◽  
Author(s):  
Zhi Wu Zhu ◽  
Guo Zheng Kang ◽  
Dong Ruan ◽  
Yue Ma ◽  
Guo Xing Lu
Keyword(s):  
Aluminum Alloy ◽  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
High Strength ◽  
Dynamic Mechanical Properties ◽  
Strain Rates ◽  
Hopkinson Pressure Bar ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
5083 Aluminum Alloy

5083 aluminum alloy was investigated with respect to its uniaxial dynamic compressive properties over a range of strain rates using the split Hopkinson pressure bar (SHPB). The dynamic stress-strain curves of this alloy were obtained for strain rates from 1000 s-1 to 6000 s-1. Effects of strain rate, the samples size and anti-impact capability were analyzed. The experimental results show that under impaction loading, 5083 aluminum alloy has a remarkable strengthening response to strain rate and size; in particular, the responded stress increases with increasing strain rate, which implies that this alloy has high strength and high anti-impact capability.

Sign in / Sign up

Export Citation Format

Share Document